Huawei OptiX PTN Series Bedienungsanleitung

HUAWEI TECHNOLOGIES CO., LTD.

OptiX PTN 960 Packet Transport Platform of PTN Series

Quick Installation Guide

Issue: 08

Date: 2016-01-15

No part of this document may be reproduced or transmitted in any form or by any means without prior

written consent of Huawei Technologies Co., Ltd.

Trademarks and Permissions

and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.

All other trademarks and trade names mentioned in this document are the property of their respective

holders.

Notice

The purchased products, services and features are stipulated by the contract made between Huawei and

the customer. All or part of the products, services and features described in this document may not be

within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements,

information, and recommendations in this document are provided "AS IS" without warranties, guarantees or

representations of any kind, either express or implied.

The information in this document is subject to change without notice. Every effort has been made in the

preparation of this document to ensure accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute a warranty of any kind, express or implied.

Huawei Technologies Co., Ltd.

Address:

Huawei Industrial Base

Bantian, Longgang

Shenzhen 518129

People's Republic of China

Website:

http://www.huawei.com

Email:

[email protected]

Precautions

Page 1

Tools for Installation

Introduction to the Chassis

Installing and Routing

Cables

Checking the Insatllation

Powering On the

Equipment

End

Start

Check Fiber Connection

Powering on the

Equipment

Preparation for

Installation

Installing the Chassis

Checking Cable

Connectivity

Common Cables for the

Chassis

Installing the Protection

Grounding Cable

(Mandatory)

Installing Power Cable

(Mandatory)

Installing the E1 Cable

Installing the Ethernet

Service Cable

Installing Fibers

Installing the NM

Cable

Page 2

Page 3

Pages

4-7

Pages

8-12

Page 14

Page 13

Page 15

Pages

16-17

Page 8

Pages

9-10

Page 10

Page 8

Page 16

Page 17

Expected Effect of

Installation in a 19-Inch

Cabinet

Installing the External

Clock/Time Cable

Page 11

Page 12

Installing the Chassis in a

19-Inch Cabinet

Page 4

Page 5 Installing the Chassis in an

ETSI Cabinet

Installing the Chassis in

an open rack

Page 6

Installing the Chassis

into the indoor mini box

mounted on the wall

Page 7

Installation Flow

Certain operations are optional. Before performing an optional operation, consult with the engineering

supervisor or software debugging engineer to decide whether to perform the operation. The other

operations are mandatory.

After you finish the installation, send the information about the bar code to Huawei Headquarters

according to the Tabulation for the Feedback of Bar Codes of Equipment at Stations.

Precautions

NOTE

Bundling cables

CAUTION

This document provides simple and distinctive guidelines for quick hardware installation of the PTN 950.

This document does not describe pre-delivery assembly. This document only describes procedures for onsite

installation.

Electrostatic Discharge

Always wear an anti-static ESD wrist strap when handling the equipment or sensitive components to prevent

electrostatic discharge causing possible bodily injury or damage to the equipment or sensitive components. Ensure

that the other end of the ESD wrist strap is properly grounded.

Binding intervals between cable ties or optical fiber binding straps inside the cabinet cannot exceed 250 mm.

(Binding intervals cannot exceed 200 mm for user cables).

Binding intervals between cable ties for all cables and corrugated pipes outside the cabinet are determined based on

the distance between the two horizontal beams. If the cable trough does not contain any beams, the binding intervals

between cable ties cannot exceed 250 mm.

Verify that the equipment room, power supply, ground cables and optical cables are ready for installation. Start the

installation according to the engineering design documents after confirming that conditions are met. Refer to the

Installation Guide for information about specific operational requirements and technical specifications.

Pre-Installation Check

CAUTION

The PTN 960 supports indoor and outdoor installation. Ensure that the requirements on device operating

environments are met before installation. Using the outdoor cabinets IMB network box, APM30H, and R01S200 can

moderately improve the device operating environments. You can use the ETP4830 external AC power system to

supply power to the network boxes and outdoor cabinets. If you need to use an outdoor cabinet other than the IMB

network box, APM30H, and R01S200 for the PTN 960, contact Huawei to determine whether the outdoor cabinet

meets requirements of Huawei devices on the device operating environments.

Tape measure Philips screwdriver

(M2-M6) Flathead screwdriver

(M2-M6) Adjustable wrench

Level bar

Ratchet crimp tool Cable cutter

Wire stripper Network cable crimping

pliers Diagonal pliers

Crimping tool Sharp-nose pliers

Bayonet wrench

Paper knife

Marker pen

Electric iron

Heat gun

Multimeter

Antistatic gloves

Binding strap Insulation tape

Antistatic wrist strap

Punching wire pliers

Cleaner

Tools for Installation

Coax stripper Cable tester

Optical power meter BER tester

1Introduction to Interfaces

Introduction to the Chassis

Installation holes for N63E/19-inch

cabinet and open rack

Installation holes for T63 cabinet

2Introduction to Installation Holes on Both Sides of the Chassis

Alarm interface PGND point (19-inch

cabinet)

Power interface

Ethernet service interface

Clock and time interface

10GE Optical interface

Antistatic jack interface

FE\GE Optical interface

NM interface

E1 interface

•The interface shown in the figure is for reference only. The front view is subject to the real PTN 960 equipment.

•The U-shaped slots help you tighten the chassis conveniently.

OptiX

PTN960

The PTN 960 is available in two models: common chassis and extended chassis, which are 2 U and 3 U

high, respectively. Installation modes of the two types of chassis are basically the same; therefore, the

common chassis is used as an example to describe the installation of the PTN 960 in this document. For

information about the installation of the extended chassis, refer to the Appendix.

Installing the chassis

1Scenario I: Installing the Chassis in a 19-Inch Cabinet

Installing the chassis in the cabinet

bInstalling the PGND cable

Introduction to the cable guiding frame Fixing the floating nuts

2.0±0.2 N·M

Part 1(for a 19-inch cabinet, an

ETSI cabinet, a T63 cabinet or

an open rack)

Mark the position that captive nuts are to be installed to

ensure that captive nuts are correctly installed, and

install four captive nuts on both sides of the rack.

Part 1 cable

guiding frame

2. Place the chassis's

mounting ears and

cabling rack U-shaped

slots over the screws,

tighten the screws at the

bottom.

1.Hang the screws of

the mounting ears on

the chassis to the rack

loosely.

3. use screws to tighten

the top of the chassis. 1.4±0.14 N·M

3.0±0.3 N·M

2. use the removed screw to tighten the

PGND cable.

1.Remove one screw for installing PGND cable before

installing the chassis in the cabinet.

The U-shaped slots help

you tighten the cabling rack

using screws.

Bridging

mounting ears

2Scenario II: Installing the Chassis in an ETSI Cabinet

Fixing the floating nuts

aInstalling the mounting ears

Installing the PGND cable

cInstalling the chassis in the cabinet

To the grounding point on the

rear rack column of the cabinet

Part 1 cable

guiding frame

M6 screw assembly with flat

washers

Before installing the chassis in an ETSI cabinet, adjust

the mounting holes according to the cabinet type.

3.0±0.3 N·M

2.0±0.2 N·M

1.4±0.14 N·M

Mark the position that captive nuts are to be installed to

ensure that captive nuts are correctly installed, and

install four captive nuts on both sides of the rack.

3Scenario III: Installing the Chassis in an Open Rack

Fixing the floating nuts

Installing the chassis in the open rack

bInstalling the PGND cable

2.0±0.2 N·M

To the ground points in the indoor ground bar

If the rack is with round holes,

captive screws can be

fastened without requiring any

captive nuts.

2. Place the chassis's

mounting ears and

cabling rack U-shaped

slots over the screws,

tighten the screws at the

bottom.

1.Hang the screws of

the mounting ears on

the chassis to the rack

loosely.

3. use screws to tighten

the top of the chassis.

PTN 960 Horizontally installed

4Scenario IV: Installing the Chassis into the indoor mini box

mounted on the wall

Installing the indoor mini box (IMB) on the wall

(a) Right-side-

mounted on the wall (b) Left-side-

mounted on the wall

(

c) Back-mounted on

the

wall

•1. PTN 960 can be installed in the IMB mounted on the wall.

•2. For details about the installation in scenario IV, see "Equipment Installation Guidelines (IMB

Network Cabinet)" in the Installation Guide.

Installing the chassis in the network cabinet of the customer

OptiX

PTN960

PTN 960 vertically installed

Ventilation

OptiX

PTN960

Ventilation

The modes of installing the PTN 960 in the network cabinet of the customer vary with the specifications for

the network cabinet of the customer. The following section describes two common modes to serve as a

guide for installation.

Andere Handbücher für OptiX PTN Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Huawei Netzwerk-Router Handbücher

Huawei

Huawei B2368 Bedienungsanleitung

Huawei

Huawei S6700 Series Leitfaden

Huawei

Huawei B593s-931 Technische Daten

Huawei

Huawei B315 Series Bedienungsanleitung

Huawei

Huawei AR2200 Series Bedienungsanleitung

Huawei

Huawei Quidway S9300 Bedienungsanleitung

Huawei

Huawei UR-LPUF Handbuch

Huawei

Huawei SmartAX MT882 Bedienungsanleitung

Huawei

Huawei Quidway S9300 Bedienungsanleitung

Huawei

Huawei HG531s Bedienungsanleitung

Huawei

Huawei Quidway NetEngine80E Bedienungsanleitung

Huawei

Huawei Quidway S6500 Series Montageanleitung

Huawei

Huawei SmartAX MT882 Bedienungsanleitung

Huawei

Huawei B593 Produktinformationsblatt

Huawei

Huawei NetEngine5000E Bedienungsanleitung

Huawei

Huawei EchoLife EG8041V5 Bedienungsanleitung

Huawei

Huawei LTE CPE B593 Bedienungsanleitung

Huawei

Huawei OptiXstar EG8010Hv6-10 Bedienungsanleitung

Huawei

Huawei EchoLife HG8240 Bedienungsanleitung

Huawei

Huawei B681-54 Bedienungsanleitung

Huawei

Huawei NT3BB-4PVWN-147 Bedienungsanleitung

Huawei

Huawei EchoLife EG8245H5 Bedienungsanleitung

Huawei

Huawei AOLYNK S1505L Bedienungsanleitung

Huawei

Huawei Aolynk VDR824 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise