Huawei UPS5000-E Series Bedienungsanleitung

Issue: 04

Part Number: 31508115

Date: 2019-06-20

UPS5000-E-(25 kVA–125 kVA)-FM

Quick Guide

1Overview

UPS Model Capacity Configuration Weight (Full

Configuration) Dimensions (H x W

x D)

UPS5000-E-125K-FM 25 kVA, 50 kVA, 75 kVA,

100 kVA, 125 kVA 330 kg 2000 mm x 600 mm

x 850 mm

(1) Mains input switch

(2) Bypass input switch

(3) Surge protective

module (optional)

(4) Control module

(5) Bypass module

(6) Power modules

(7) Monitor display

module (MDU)

(8) Output switch

(9) Maintenance

bypass switch

1. Before installation, read the user manual carefully to get familiar with product information and

safety precautions.

2. Use insulated tools when installing the equipment.

3. Only engineers certified by Huawei or its agent are allowed to install, commission, and maintain

the UPS. Otherwise, personal injury or equipment damage may occur, and the resulting UPS

faults are beyond the warranty scope of Huawei.

Installation Process

2(Optional) Installing the Top Outlet Kit

1. Remove the top cover from the UPS cabinet, and secure the top outlet kit using four M5 x 10

tapping screws.

2. Remove the rear cover from the UPS cabinet.

3. Connect the power cable and signal cable to the top outlet kit.

Connect the signal cable to the J33 terminal on the parallel board, and connect the power cable

to the W and N bars.

4. After cables have been connected, turn the fan switch to ON, and install the fan cover

on the top of the cabinet using four M5x10 tapping screws.

5. Install the rear baffle plate on the rear cover of the cabinet, and then install the rear cover on the

cabinet.

3Installing the UPS

1. Determine the mounting holes based on

the marking-off template, drill holes, and

install expansion sleeves.

3. Remove the rear cover from the cabinet,

open the cabinet front door, and remove

the four rubber plugs from the bottom of

the cabinet.

5. Reinstall the rear cover for the cabinet.

2. Adjust the anchor bolts and ensure that the

anchor bolts touch the floor. Then level the

UPS.

4. Secure the UPS.

4Connecting Cables

•Prepare cables away from the cabinets to prevent scraps from falling inside. Cable scraps may

ignite and cause personal injury or device damage.

•After cables have been installed, clean the cabinets in a timely manner. Keep the cabinets and

surrounding environment clean and tidy.

•You need to prepare terminals onsite. The stripped length of the copper wire should be the

same as that of the part of the terminal that covers the conductor.

UPS Cable Connection Reference

4.1

The cabling route is for reference only. Connect cables based on site requirements.

NOTE

Installing Cables

4.2

Scenario 1: Routing Cables from the Top

1. Remove filler panels from the power

distribution subrack, and remove covers

from the top of the cabinet based on the site

requirements.

2. (Skip this step if the mains input and bypass

input share a power source.) Remove the

copper bars between the mains input and

bypass input.

3. Connect the ground cable, power cable, and signal cable. There is no need to connect the

bypass input power cable if the mains input and bypass input share a power source.

Signal cable

Port

Description Bolt

Specifications Torque

Mains input M10x30 26 N•m

Bypass input M10x30 26 N•m

Battery input M12x35 46 N•m

Output M10x30 26 N•m

PE M10x30 26 N•m

NOTE

The wire routed from the middle point of positive

and negative battery strings is the neutral wire.

Take a battery string consisting of 40 batteries for

example. The battery neutral wire is routed from

the middle between positive and negative battery

strings, each consisting of 20 batteries.

Scenario 2: Routing Cables from the Bottom

1. Remove filler panels from the

front of the cabinet. 2. Switch the top covers and beam with the

bottom covers.

In bottom cable routing scenarios, a cable entry cabinet is required only if the cross-sectional

area of cables is greater than 150 mm2.

NOTE

3. Remove cable covers based on site requirements.

4. (Skip this step if the mains input and bypass input share a power source.) Remove the copper

bars between the mains input and bypass input.

5. Connect the ground cable, power cable, and signal cable. There is no need to connect the

bypass input power cable if the mains input and bypass input share a power source.

Signal cable

5Verifying the Installation

1. Check that there is no foreign matter at the top and bottom of the cabinet, copper bars, switches,

and the rear of modules.

2. After verifying the installation, reinstall all

the covers.

3. (Remove the paper protective film from the

sealing putty.) After routing cables and

verifying cable connections, seal the gap

between cables and the cabinet using

sealing putty.

Dustproof cover

4. Do not remove the dustproof cover before

power-on to prevent dust inside the UPS.

Sealing putty

Sealing putty must be used as a whole and

the gap can be sealed only from the top.

Paper

protective film

6Powering On and Starting the UPS

1. Before powering on the UPS, ensure that the UPS has passed all check items in the UPS5000

Commissioning and Acceptance Report and Chapter 5.

2. Measure the voltage and frequency of the UPS upstream input switch. The line voltage range is

138–485 V AC, and the frequency range is 40–70 Hz.

Powering On the UPS

6.1

Close the upstream input switch.

Close the UPS bypass input switch, output switch, and mains input switch.

After the UPS is powered on, initialization begins. The MDU displays the Huawei logo and an

initialization progress bar.

Battery

Specifications

Number of

Batteries

Connected in

Series

Number of Battery

Strings Connected

in Parallel to the

UPS

Number of

Cells

Battery Capacity

100 Ah/12 V

32 x 6 = 192

100 Ah + 100 Ah = 200

100 Ah/2 V

192

192 x 1 = 192

100 Ah + 100 Ah = 200

100 Ah/12 V

40 x 6 = 240

100 Ah + 100 Ah + 100

Ah = 300 Ah

100 Ah/2 V

240

240 x 1 = 240

100 Ah + 100 Ah + 100

Ah + 100 Ah = 400 Ah

•

Number of cells indicates the number of 2 V DC batteries in a battery string connected to the

UPS.

•If multiple UPSs share battery strings, the battery capacity of each UPS is the total capacity of the

battery strings.

Setting Key Parameters

6.2

Andere Handbücher für UPS5000-E Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Huawei UPS Handbücher

Huawei

Huawei UPS5000-H-600 kVA-FT Bedienungsanleitung

Huawei

Huawei PDU8000 Series Bedienungsanleitung

Huawei

Huawei UPS5000-A-400 kVA Bedienungsanleitung

Huawei

Huawei UPS2000-H Bedienungsanleitung

Huawei

Huawei UPS2000-G-6KRTLL Bedienungsanleitung

Huawei

Huawei UPS5000-A-30 kVA Bedienungsanleitung

Huawei

Huawei UPS5000-E-60K-F60 Bedienungsanleitung

Huawei

Huawei PDU8000 Series Bedienungsanleitung

Huawei

Huawei UPS5000-E Series Bedienungsanleitung

Huawei

Huawei UPS5000-E Series Bedienungsanleitung

Huawei

Huawei UPS5000 Bedienungsanleitung

Huawei

Huawei UPS5000-E Series Bedienungsanleitung

Huawei

Huawei UPS5000-A-600K-SC Bedienungsanleitung

Huawei

Huawei UPS5000-S-1200 kVA Bedienungsanleitung

Huawei

Huawei UPS5000-E-180 kVA Bedienungsanleitung

Huawei

Huawei UPS5000-H Series Bedienungsanleitung

Huawei

Huawei UPS5000-E-25K-SM Bedienungsanleitung

Huawei

Huawei UPS5000-S Series Bedienungsanleitung

Huawei

Huawei UPS2000-G-2KRTL Bedienungsanleitung

Huawei

Huawei UPS5000-A-400K-FTS Bedienungsanleitung

Huawei

Huawei UPS5000-A-300K-FT Bedienungsanleitung

Huawei

Huawei UPS5000-S-400K-SM Bedienungsanleitung

Huawei

Huawei UPS5000-E-25 kVA-BF Bedienungsanleitung

Huawei

Huawei UPS5000-S-600 Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mecer

Mecer ME-1000-WTU Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

Eaton

Eaton 3S Montageanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung