Huawei UPS5000-E-400K-FMS Bedienungsanleitung
1
Issue: 05
Part Number: 31509985
Date: 2022-06-20
UPS5000-E-(400 kVA-600 kVA)
Quick Guide (60 kVA Power Modules)
1Overview
Model
UPS5000
-E-400K-FMS
UPS5000
-E-400K-FMS-01
UPS5000
-E-500K-FMS
UPS5000
-E-500K-FMS-01
UPS5000
-E-600K-FMS
UPS5000
-E-600K-FMS-01
Weight (
full
configuration)
680 kg
800 kg
1025 kg
Dimensions (H x
W x D)
2000 mm x 1200 mm x 850 mm
2000 mm x 1400 mm x 850
mm
1. Before installation, read the user manual carefully to get familiar with product information
and safety precautions.
2. Use insulated tools during installation and operation.
3. Only engineers certified by the Company or its agent are allowed to install, commission, and
maintain the UPS. Otherwise, personal injury or equipment damage may occur, and the
resulting UPS faults are beyond the warranty scope.
(1) Power modules
(2) Control module
(3) Power distribution
module covers
(4) Maintenance bypass
switch
(5) Bypass module
(6) Main input switch
(7) Output switch
(8) Bypass input switch
UPS5000-E-400K-FMS
UPS5000-E-400K-FMS-01
UPS5000-E-500K-FMS
UPS5000-E-500K-FMS-01
Copyright © Huawei Digital Power Technologies Co., Ltd. 2022.
All rights reserved.
2
Determining the UPS Installation Position
2.1
The UPS can be installed on the channel steel or floor. Determine the mounting hole positions using
a marking-off template (unit: mm), drill holes, and install expansion sleeves based on site
requirements.
2Installing the UPS
UPS5000-E-600K-FMS
UPS5000-E-600K-FMS-01
(1) Power modules
(2) Control module
(3) Power distribution
module covers
(4) Maintenance
bypass switch
(5) Bypass module
(6) Main input switch
(7) Output switch
(8) Bypass input
switch
UPS5000-E-400K-SMS, UPS5000-E-500K-SMS, and UPS5000-E-600K-F600-SMS, UPS5000-E-
400K-SMS-01, UPS5000-E-500K-SMS-01, UPS5000-E-600K-SMS-01 are models in standard
configuration. A UPS in standard configuration has no mains input switch, bypass input switch,
or output switch.
3
A: Mounting holes on the channel steel B: Mounting holes on the floor
Unit: mm
400/500K Hole Dimensions
600K Hole Dimensions
Unit: mm
4
Installing the Front, Rear, Left, and Right Anchor Baffle Plates
2.3
3Installing Cables
UPS Cable Connection Reference
3.1
•Prepare cables away from the cabinets to prevent scraps from falling inside. Cable scraps
may ignite and cause personal injury or device damage.
•After cables have been installed, clean the cabinets in a timely manner. Keep the cabinets
and surrounding environment clean and tidy.
•You need to prepare terminals onsite. The stripped length of the copper wire should be the
same as that of the part of the terminal that covers the conductor.
•Floor mounting: Secure the cabinet to the floor by using eight M12x60 expansion bolts.
•Channel steel mounting: Secure the cabinet to channel steel by using eight M12x60 common
bolts.
(1)
Cabinet mounting holes (floor mounting mode)
(2)
Cabinet mounting holes (channel steel mounting mode)
Securing the UPS
2.2
5
1. Open the front door of the bypass
cabinet, and remove power distribution
covers (UPS5000-E-400K-FMS is used as
an example).
Installing Cables
3.2
The cabling route is for reference only. Connect cables based on site requirements.
3.2
2. Remove the top cover from the
cabinet based on cable routes and
dimensions.
Scenario 1: Routing Cables from the Top
6
5. Connect the mains input power cable. 6. Connect the output power cable.
3. Remove the copper bar between the mains
and bypass inputs. (Skip this step if there is
only one power source.)
4. Connect the ground cable to the UPS.
7
9. Connect signal cables.
The figure shows the signal cable routing
and is for reference only. Connect the
cable based on the actual situation.
Route a neutral wire from the middle of the
positive and negative battery strings.
Take a battery string consisting of 40 batteries as
an example. A neutral wire is routed from the
middle of positive and negative battery strings,
each consisting of 20 batteries.
7. Connect the bypass input power cable. 8. Connect the battery cable.
For the cable connection method for
the TN-C system, see the user manual.
8
(1) Switches
(2) Mains input wiring
copper bars
(3) Battery input
wiring copper bars
(4) Output wiring
copper bars
(5) Bypass input wiring
copper bars
(6) Rear of the cabinet
4Verifying the Installation
1. Check that there is no foreign matter
in the cabinet.
Scenario 2: Routing Cables from the Bottom
For the screw specifications and torque used for
connecting cables in a bottom cable routing
scenario, refer to the top cable routing scenario.
This section only shows the cable routes in the
bottom cable routing scenario.
1. Remove the cable covers from the bottom of the cabinet, drill holes in the covers, attach
grommet strips to the hole edges for protecting cables, and reinstall the cable covers.
2. Connect power cables and signal cables.
9
5Powering On and Starting the UPS
1. Before powering on the UPS, ensure that the UPS has passed all check items in the
UPS5000
Commissioning and Acceptance Report
and Chapter 4.
2. Measure the voltage and frequency of the mains and bypass inputs of the UPS, or the
voltage and frequency output from the external input power distribution cabinet (PDC) to
the UPS. Ensure that the line voltage is in the range of 138–485 V AC and the frequency is in
the range of 40–70 Hz.
Dust cover
3. After verifying the installation, reinstall all the covers.
4. Do not remove the dust cover before power-on to prevent dust from entering the UPS.
2. After routing cables and checking cable connections, use sealing putty to fill in the gap
between the cables and the cabinets. (Remove the paper protective film from the sealing putty
and retain the transparent film. When using the putty, ensure that the transparent film faces
upward.)
Sealing putty must be used as a whole and the gap can be sealed only from the top.
Paper
protective
film Sealing putty
Transparent film
10
Starting the Inverter
5.2
Powering On the UPS
5.1
Turn on the upstream bypass and mains input switches.
(For a UPS in full configuration) Turn on the UPS bypass input switch, output switch, and mains
input switch.
After the UPS is powered on, initialization begins. The MDU displays an initialization progress bar.
Download and install the Service Expert app.
After login, tap Power-on password
activation on the screen. A message is
displayed, indicating whether to start the UPS.
Tap OK.
Insert the WiFi module into the USB port on
the MDU. Enable the mobile phone WLAN,
search for the UPS_WIFI signal, and connect to
the WiFi signal. The password is Changeme.
Set the Site and Device Type as required, and
connect the device. Set IP to 192.168.0.10, Port
to 443, Username to admin, Password to
Changeme, and tap Login.
Enter Bar code and Verification code
obtained from the LCD on the Offline
Activation screen. Tap Generate PWD to
generate a startup password.
Set Site and Device Type as required,
and tap Offline Activation.
Enter the generated password in the
password textbox on the LCD to start the
UPS.
Use the app to
start the UPS
online?
Yes
No, start
the UPS
offline
On the app home screen, tap StartUp to access the Set Startup screen.
•If the UPS is powered on for the first time, you need to obtain the startup password from the
Service Expert app. Skip this step if the UPS is not powered on for the first time.
•The Service Expert app can be downloaded from HUAWEI AppGallery and can only run on
Android.
•The Settings Wizard screen may vary with versions. The parameters depend on the actual
product.
1. Obtain the startup password.
Dieses Handbuch passt für folgende Modelle
5
Inhaltsverzeichnis
Andere Huawei UPS Handbücher
Huawei
Huawei UPS5000-E Series Bedienungsanleitung
Huawei
Huawei UPS5000-E-600 kVA Bedienungsanleitung
Huawei
Huawei UPS2000-G-3K-V1-DR Bedienungsanleitung
Huawei
Huawei SmartLi Series Bedienungsanleitung
Huawei
Huawei UPS2000-H Bedienungsanleitung
Huawei
Huawei PDC-0038V4ACIOA-V2 Bedienungsanleitung
Huawei
Huawei UPS5000-A-30 kVA Bedienungsanleitung
Huawei
Huawei UPS2000-G-15KRTL Bedienungsanleitung
Huawei
Huawei PAC3000S12-T1 PSU Bedienungsanleitung
Huawei
Huawei UPS2000-G-2KRTL Bedienungsanleitung
Huawei
Huawei UPS2000-H Bedienungsanleitung
Huawei
Huawei UPS5000-E-400K Series Bedienungsanleitung
Huawei
Huawei UPS5000-E Series Bedienungsanleitung
Huawei
Huawei UPS5000-S200K-SM Bedienungsanleitung
Huawei
Huawei UPS5000-E Series Bedienungsanleitung
Huawei
Huawei UPS5000-H Series Bedienungsanleitung
Huawei
Huawei UPS5000-S Series Bedienungsanleitung
Huawei
Huawei UPS2000-A-6KTTS-S Bedienungsanleitung
Huawei
Huawei UPS5000-S-880 kVA Bedienungsanleitung
Huawei
Huawei PDU8000 Series Bedienungsanleitung
Beliebte UPS Handbücher anderer Marken
Pylontech
Pylontech Victron & Pylontech US5000 Bedienungsanleitung
Tecnoware
Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung
Mecer
Mecer ME-1000-WTU Bedienungsanleitung
Mustek
Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch
Emerson
Emerson Liebert NXL series Bedienungsanleitung
MAKELSAN
MAKELSAN BOXER SERIES Bedienungsanleitung
