Hubbell KILLARK ACCEPTOR UGR Series Bedienungsanleitung

Page 1 of 3

3940 Dr. Martin Luther King Drive

St. Louis, MO 63113

P/N 00911678 FORM NO. K1007 R9/15 ECO-7-019-15

INSTALLATION, OPERATION &

MAINTENANCE DATA SHEET

THE “ACCEPTOR®” SERIES “UGR” & “UGR…QW”

RECEPTACLES

THE “ACCEPTOR®” SERIES “UGR” &

“UGR…QW” RECEPTACLES

CAUTION:

Before installing, make sure you are compliant with area classications, failure to do so may result in bodily injury,

death and property damage. Do not attempt installation until you are familiar with the following procedures. All

installation must comply with the applicable Electrical Code.

Make sure that the circuit is de-energized before starting installation or maintenance.

Verify that the installation is grounded. Failure to ground will create electrical shock hazards, which can cause

serious injury and or death.

Technical information, advice and recommendations contained in these documents is based upon information

that Killark believes to be reliable. All the information and advice contained in these documents is intended for

use only by persons having been trained and possessing the requisite skill and know-how and to be used by

such persons only at their own discretion and risk. The nature of these instructions is informative only and does

not cover all of the details, variations or combinations in which this equipment may be used, its storage, delivery,

installation, check out, safe operation and maintenance. Since conditions of use of the product are outside of the

care, custody and control of Killark, the purchaser should determine the suitability of the product for his intended

use, and assumes all risk and liability whatsoever in connection therewith.

Page 2 of 3

3940 Dr. Martin Luther King Drive

St. Louis, MO 63113

P/N 00911678 FORM NO. K1007 R9/15 ECO-7-019-15

WARNING: Electrical power MUST BE

OFF during installation, or performing any

maintenance. Disconnect primary power

source and lock out. This device must

be installed by trained, qualied and

competent personnel. Installation must

comply with local, state and national

regulations, as well as safety practices for

this type of equipment.

CAUTION: To reduce the risk of ignition

of hazardous atmospheres, do not use

Class II, Group F locations that contain

electrically conductive dusts.

Before installing, check the carton label

and product nameplate to be sure you

have the correct type.

INSTALLATION DRAWINGS

1. DIRECTIONS FOR INSTALLATION

RECEPTACLE: The series “UGR” Receptacle

must be installed as directed below for the specic

hazardous location in which it is to be used. (Vertical

position only for Class II, Gr. F&G and/or Raintight).

For use with Killark Type “UGP” plugs and other plugs

specied on Form No. K1092, also provided with this

product.

1. Using the drawings at the left as a guide, securely

mount the outlet box in a suitable location and

install conduit. Receptacles for Class I, Group B are

provided with single gang Series “SWB” mounting

box. All conduits must be provided with a sealing

tting within 6 inches of the box. Receptacles for

Class I, Groups C&D may be provided with single

or double gang mounting boxes, or may be eld

assembled with Series “SWB” mounting boxes, Cat.

Nos. SWB-1 through SWB-12.

2. Pull supply wires through conduit system and into box.

NOTE: Use only Copper wire with this device (10, 12

or 14 AWG).

3. UGRO WIRING (for UGRO…QW Wiring, See

next page): Loop the wires and attach them to

the proper terminal screws: Green lead (Ground, if

provided) to screw at Ground strap (marked Green);

White (Neutral) lead to terminal at White mark (125V

only); Black and/or Red [Line lead(s)] to unmarked

terminal(s).

Page 3 of 3

3940 Dr. Martin Luther King Drive

St. Louis, MO 63113

P/N 00911678 FORM NO. K1007 R9/15 ECO-7-019-15

Figure 1

“QW” TERMINAL CONNECTIONS

4. Check the ange surfaces of both the box and the

receptacle cover to be sure they are clean, smooth;

free of nicks, scratches, dirt or any foreign particles

that would prevent a proper seal. Apply a light coating

of Killark “LUBG” lubricant to the anges and , after

pushing wiring into box, install cover to box, using the

(4) screws provided. Tighten the screws to 5 ft. lbs.

torque. After tightly bolting the cover assembly to the

box, the box to cover ame joint should be checked

with a 0.0015” thick feeler gauge, such that the gauge

will not enter the joint more than 1/8” at any point.

2. OPERATIONAL DATA

NOTE: UGRx receptacles WILL NOT operate with

ordinary plugs; UGP series plugs must be used. See

UGP instruction sheet K1377 for more information.

1. Lift receptacle door and insert plug all the way into the

receptacle.

2. Turn plug to clockwise limit (45°). This closes internal

contacts and completes circuit.

3. Release plug. Plug will move outward to “LOCK”

position. Check by trying to turn plug without pushing

inward; plug should not turn.

4. To remove plug, push plug inward and turn to counter-

clockwise limit (45°). Pull plug straight out.

UGRO…QW WIRING (See Figure 1) :

NOTE: Use only copper wire with this device (10, 12

or 14 AWG). Recommended wire strip length – ½

inch nominal (wire strip gauge also available on the

QW terminal cover). Loosen all (3) Terminal Contact

Screws and insert wire through the Wiring Entrance

holes, into proper terminals: Green lead (Ground)

to terminal with ground mark & Green screw head;

White (Neutral) lead to terminal with Silver screw

head (125V. only); Black and/or Red [Line lead(s)]

to terminal(s) with Brass screw head. Hand tighten

terminal screws (recommended torque 8 in.-lbs.

3. MAINTENANCE DATA

These receptacles require no maintenance other than

a periodic cleaning and a check for damage and/or

loose fasteners. These items should be performed on

a regular basis, determined by the environment and

usage.

WARNING: Disconnect and Lock Out supply circuit

before starting maintenance work.

1. To clean receptacle it is recommended that a soft,

non-metallic bristle brush be used.

2. Check tightness of all accessible screws.

3. Inspect the entire assembly for damage and/or wear.

Consult Killark factory for availability of replacement

parts and discontinue use of the equipment until

repairs are made.

Dieses Handbuch passt für folgende Modelle

Andere Hubbell Zubehör Handbücher

Hubbell

Hubbell Gear Drive Electric Cable Reels SM21 Bedienungsanleitung

Hubbell

Hubbell AFBS1R4 Series Bedienungsanleitung

Hubbell

Hubbell INSULGRIP HBL4100RS1W Betriebsanleitung

Hubbell

Hubbell KILLARK VSI30 Series Bedienungsanleitung

Hubbell

Hubbell H-MOSS ATP1274 Bedienungsanleitung

Hubbell

Hubbell LightHawk LHMT Bedienungsanleitung

Hubbell

Hubbell LightOWL LODT Handbuch

Hubbell

Hubbell Direct Drive Electric Cable Reels S-32 Bedienungsanleitung

Hubbell

Hubbell Electric Cable Reels SHO Series Bedienungsanleitung

Hubbell

Hubbell LightOWL LODT Handbuch

Hubbell

Hubbell Gear Drive Electric Cable Reels SM-28 Bedienungsanleitung

Hubbell

Hubbell NX Distributed Intelligence NXSMP-LMI Bedienungsanleitung

Hubbell

Hubbell BTSMP-HMO Bedienungsanleitung

Hubbell

Hubbell H-MOSS ATD500C Bedienungsanleitung

Hubbell

Hubbell Gear Drive Electric Cable Reels MMD21 Bedienungsanleitung

Hubbell

Hubbell NX Distributed Intelligence NXSMP-OMNI Bedienungsanleitung

Hubbell

Hubbell Gear Drive Electric Cable Reels SM32 Bedienungsanleitung

Hubbell

Hubbell Direct Drive Electric Cable Reels MMD32 Bedienungsanleitung

Hubbell

Hubbell WS2001NS Series Bedienungsanleitung

Hubbell

Hubbell Single Motor Controller 4015 Bedienungsanleitung

Hubbell

Hubbell Universal Cable Reel-Direct Drive UE24 Bedienungsanleitung

Hubbell

Hubbell H-MOSS Bedienungsanleitung

Hubbell

Hubbell Direct Drive Electric Cable Reels S-16 Bedienungsanleitung

Hubbell

Hubbell PIR 10 Series Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung