Hunter Set & Save 47300A Bedienungsanleitung

Owner’s Manual Model 47300A

Programmable Thermostat

TEMP

41665-01.pmd 9/30/03, 4:52 PM1

Introduction

CONGRATULATIONS!

Your new Hunter electronic thermostat will provide

years of reliable service. By saving energy, your ther-

mostat will pay for itself during its first season of

use. Thank you for buying a Hunter product!

Please read this manual for complete instructions on

installing and operating your thermostat.

If you require further assistance, call Hunter Techni-

cal Support at 1-866-268-1936 from 8 a.m. to 5 p.m.

Central Time.

Model Information:

Model Number ___________________________________________

Serial Number____________________________________________

Date Purchased __________________________________________

Where Purchased _________________________________________

47300A

41665-01.pmd 9/30/03, 4:52 PM2

Table of Contents

Read This Before Installing Thermostat 5

Features 7

What You Need 8

Remove Old Thermostat 8

Wire Labeling 9

Mount Wallplate and Thermostat 11

Connect Wires and Mount Thermostat Cover to Wall Plate 12

Selector Switches 13

Setting Time and Day 14

Default Programs 16

Personal Program Schedule 17

Manual Programming 18

Weekday / Weekend Programming 19

7-Day Programming 21

Reviewing Programs 22

Reviewing the Current Temperature Setting 23

System Selector Switch 24

Fan Switch 24

Temporary Manual Override 25

INTRODUCTION

INSTALLATION

PROGRAMMING

OPERATIONS

(continued)

41665-01.pmd 9/30/03, 4:52 PM3

Permanent Manual Override 26

Vacation Override (Programmable Hold) 27

Home Today 28

Energy Monitor 30

Filter Monitor 31

Auto Recovery 32

SPAN Setting Mode 34

Low Battery Warning 36

Error Mode 37

Auto Cut-Off 37

Problems & Solutions 38

Technical Support 39

Heat / Cool Systems 40

Single-Stage Heat Pump Systems 41

Heat Only / Cool Only Systems 41-42

Table of Contents (continued)

OPERATIONS

(continued)

SAFETY FEATURES

TROUBLESHOOTING

WIRING DIAGRAMS

41665-01.pmd 9/30/03, 4:52 PM4

Read This Before Installing Thermostat

IMPORTANT

1Read the entire installation section of this

Owner’s Manual thoroughly before you begin

to install or operate your Hunter Thermostat.

REMOVE THE MYLAR LABEL FROM THE LCD DISPLAY

WINDOW.

INSTALLATION

2All installation is normally performed at your

thermostat.

ARMCHAIR PROGRAMMING

3You can program your thermostat before

installation by inserting the batteries and following

the instructions starting on page 16.This can be done

while you relax in your favorite chair and is a very

good way to familiarize yourself with all the functions

of your Hunter Thermostat.

OPERATION

4Your Thermostat is designed to operate with

most gas, oil, electric or 2-wire hot water heating

and air conditioning systems. It will also operate

single-stage heat pumps that do not have auxiliary

or emergency heat. These have 24-volt or millivolt

control systems and represent most central heating,

air conditioning, or space heating units in use in the

United States.

This Hunter Thermostat will NOT control multi-

stage heat pumps or 110/220 Volt systems.

COMPRESSOR PROTECTION

5The thermostat provides a 3.5 minute delay after

shutting off the heating or cooling system before

it can be restarted. This feature will prevent damage

to your compressor caused by rapid cycling. Note

that this delay also applies to the heating system

control. It does not prevent a rapid compressor re-

start due to short power outages.

TEMPERATURE RANGE

6Your thermostat can be programmed between

4°C and 35°C (45°F and 95°F). However, it will

display room temperatures from 0°C and 37°C (32°F

to 99°F). “HI” will be displayed if the temperature is

higher than 37°C (99°F), and “LO” will be displayed

if the temperature is lower than 0°C (32°F).

This thermostat will automatically cut off in Heat

mode if the temperature rises above 35°C (95°F),

and automatically cut off in cool mode if the tem-

perature drops below 7°C (45°F).

41665-01.pmd 9/30/03, 4:52 PM5

Read This Before Installing Thermostat (continued)

POWER FAILURE

7Whenever the main power is interrupted or fails,

the battery power retains the programs and cur-

rent time.

AUTO RECOVERY

8Your thermostat is set from the factory to gradually

recover the room temperature from an energy sav-

ing program to your comfort program.Therefore, the

thermostat may turn your system on several minutes

prior to your programmed time. This operation is nor-

mal, but can be turned off. Refer to the Selector

Switches information on page 24.

BATTERY WARNING

9Fresh alkaline batteries should provide over one

year of service. However, when the batteries be-

come drained, the Low Battery indicator will flash on

the display. When this message occurs, install 2 new

AA batteries. You have approximately 1 minute to

change the batteries and keep thermostat’s clock and

program settings. Once the batteries have become too

low to ensure proper operation, your system will be

turned Off, and the display will be cleared except for

the Low Battery indicator flashing on the LCD display.

CAUTION:

Once the Low Battery only display oc-

curs, the thermostat is shut down, and your sys-

tem will no longer operate. In this condition,

there is no temperature control of your dwelling.

NOTE:

If you plan to be away from the premises

over 30 days, we recommend that you replace

the old batteries with new alkaline batteries

prior to leaving.

ENERGY STAR®Partner

As an ENERGY STAR®Partner, Hunter Fan Co. has

determined that this programmable thermostat meets

the ENERGY STAR®guidelines for energy efficiency.

41665-01.pmd 9/30/03, 4:52 PM6

Features

energy

home

today

fan

auto

system

heat

cool

off

reset day/time

prog day

program

filter

hold

/return

HEAT TEMP

LCD Display: Shows time, day, temperature, program

number, and other feature information as required.

Reset: Press with a paper clip to reset the

thermostat and return to power-up settings. Program Day Key: Selects the day

or days to review or change in the

Program mode.

Energy: Measures and

displays heating and

cooling system

operating time for

Today, Yesterday, This

Week, Last Week, or

Total. By monitoring

your energy usage, you

can program the

thermostat to optimize

energy savings.

System Switch:

Selector switch for

Heat, Cool, and Off

Fan Switch: Fan

switch for Automatic

or Continuous fan

operation.

Battery Release Lever:

Push to pop batteries loose.

Hold / Return Key: Used for

setting a permanent or vacation

hold, and for returning to the

normal display from Day & Time

setting, Programming, or Span

setting modes.

Day / Time Key: Used for

entering the Clock setting mode.

Use with the Up and Down keys

to set the time and day.

Filter Key: Resets Filter Change

counter to zero.

Program Key: Used for entering

and modifying Programs. Use

with the Up and Down keys to

set times and temperatures.

Press when in Clock setting

mode to select between 12 and

24 hour clock modes.

Up and Down Keys: Keys for changing

the Temperature setting. Also used for

increasing and decreasing selections in

the Time, Program, and Span functions.

Home Today: Overrides

energy-saving program

temperatures while you are

home for the day.

41665-01.pmd 9/30/03, 4:52 PM7

INSTALLATION

What You Need

This thermostat includes two #8 screws and two wall

anchors for mounting. To install your thermostat, you

should have the following tools and materials.

■Phillips and Slotted Screwdrivers

■Hammer

■Electric drill and 3/16" bit

■Two 1.5 V (AA) size alkaline batteries

Remove Old Thermostat

CAUTION:

Do not remove any wiring from exist-

ing thermostat before reading the instructions

carefully. WIRES MUST BE LABELED PRIOR TO

REMOVAL.

■IMPORTANT! Turn off the power to the furnace at

the main power panel or at the furnace.

■Remove existing thermostat cover. See Figure 1.

Some thermostats will have screws or other lock-

ing devices that must first be removed. Once wall

mounting plate is exposed, look for wires.

If wires are not visible, they may be connected to the

back of the wallplate. Again, look for screws, tabs,

etc. Some models have doors that open to expose

wires and mounting screws. (See Figure 1).

TYPICAL HOME THERMOSTATS

Figure 1

Wall Mounting Plate Thermostat Cover

41665-01.pmd 9/30/03, 4:52 PM8

Wire Labeling

■

Each wire coming from the wall to the existing

thermostat is connected to a terminal point on

that thermostat. Each of these terminal points is

usually marked with a code letter as shown in

Table A on the next page.

■Note that this thermostat has multiple function

terminals that allow Single-Stage Heat Pump ca-

pability. Standard systems use: Rh, Rc, G, W.

[Single-Stage Heat Pumps use: Rh, Y1, G, and O or

B.] Table A below shows the multiple functions of

the terminals. Use the terminals that match your

system.

■The number of wires in your system can be as few

as two (for heat only systems), as many as eight,

or any number in between. If you follow the label-

ing procedures correctly, you do not have to be

concerned about how many wires there are.

■There is often no ter-

minal marking on the

existing thermostat of

two wire, heat only

systems. Just connect

either of the wires to

the RH terminal, then

connect the other wire

to the W terminal to

complete the circuit.

■IMPORTANT! BEFORE DISCONNECTING ANY

WIRES, APPLY THE SELF-ADHESIVE LABELS PRO-

VIDED TO THE WIRE AS SHOWN IN TABLE A ON

THE NEXT PAGE. (For example, attach the label

marked W to the wire that goes to the W or H

terminal on your existing thermostat.) IGNORE

THE COLOR OF THE WIRES since these do not

always comply with the standard.

■After labeling wires, disconnect them from the

existing thermostat terminals.

■Remove existing wallplate. To make sure wires do

not fall back into wall opening, you may want to

tape them to the wall.

■If hole in wall is larger than necessary for wires,

seal this hole with insulating material so that no

hot or cold air can enter the back of the thermo-

stat from the wall.This air could cause a false

thermostat reading.

WGYRH

(continued)

41665-01.pmd 9/30/03, 4:52 PM9

INSTALLATION

Table A

NOTE:

Do not connect a “Common” wire (sometimes labeled “C”) to any terminal on this thermostat.

Tape up the wire and do not use. This wire provides electricity to non-battery powered thermostats.

W/B

Y/O

RH, R,VR or 4

24 Volt

RC, VC

24 Volt Cool

G or F

Fan

Y, C or M

Air Conditioning Compressor

- or -

Reversing Valve operating in Cool mode.

(Single Stage Heat Pumps ONLY.)

If the code letter on your

existing thermostat is then mark the wire

with label shown and connect to thermostat

terminal shown

W or H

Heating

- or -

Reversing Valve operating in Heat mode.

(Single Stage Heat Pumps ONLY.)

Heat Pump compressor

(Single Stage Heat Pumps ONLY.)

Y/O

W/B

41665-01.pmd 9/30/03, 4:52 PM10

Inhaltsverzeichnis

Andere Hunter Thermostat Handbücher

Hunter

Hunter 40120 Konfigurationshandbuch

Hunter

Hunter Auto Temp 44402 002 Bedienungsanleitung

Hunter

Hunter 42205 Bedienungsanleitung

Hunter

Hunter Internet Thermostat Montageanleitung

Hunter

Hunter 40120 Bedienungsanleitung

Hunter

Hunter 44155C Bedienungsanleitung

Hunter

Hunter Set & Save 47350A Bedienungsanleitung

Hunter

Hunter 47377 Bedienungsanleitung

Hunter

Hunter 44260 Bedienungsanleitung

Hunter

Hunter 44008-01 Bedienungsanleitung

Hunter

Hunter 47905 Bedienungsanleitung

Hunter

Hunter 42122 Bedienungsanleitung

Hunter

Hunter 44860 Bedienungsanleitung

Hunter

Hunter 42122 Bedienungsanleitung

Hunter

Hunter 40170 Bedienungsanleitung

Hunter

Hunter 47132 Bedienungsanleitung

Hunter

Hunter 40170 Bedienungsanleitung

Hunter

Hunter 44300 Bedienungsanleitung

Hunter

Hunter 42122 Benutzerhandbuch

Hunter

Hunter 44132 Bedienungsanleitung

Hunter

Hunter 44259 Bedienungsanleitung

Hunter

Hunter 44272 Bedienungsanleitung

Hunter

Hunter 42711-01 Bedienungsanleitung

Hunter

Hunter 40135 Konfigurationshandbuch

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung