HUSKY LINERS 56561 Bedienungsanleitung

PART NO. 5659 / 5656

5659_5656 Front Instr#1170E.doc

Rev: 1

FORD F-150 WITH FACTORY FENDER FLARES

FORD F-150 WITHOUT FACTORY FLARES AND WITH FACTORY RUNNING BOARD

FRONT MUD GUARD INSTALLATION INSTRUCTIONS

Install Paint Protection Film before mud guards (see other side)

Please read instructions thoroughly before installation.

Tools Required

•1/8” drill bit / Drill

•Short #2 Phillips screwdriver

•Center punch

Package Contents

•Driver & passenger side rear mud guard

•#10 screw (qty. 6)

•Washers (qty. 6)

•Paint Protection Film (1 set)

•Instruction sheet

NOTE: Turn the front wheels all the way to the left or right for mud guard installation. However, it may be necessary

to remove the wheels depending on the tools being used for installation.

F-150 with flares

1. Clean and degrease the mud guard location area on the fender before installation.

2. Using the mud guard as a template, place the mud guard against fender, mark, center punch and drill 1/8” hole at location B

(Figure 1).

3. Attach mud guard to front fender with #10 screw and washer at location B, check fit and make sure mud guard is parallel to

ground before tightening.

4. Mark, center punch and drill 1/8” holes at locations A and C (Figure 1).

5. Install #10 screws and washers at locations A and C.

F-150 without flares and with running boards

1. Clean and degrease the mud guard location area on the fender before installation.

2. Remove existing fasteners from locations B and C (Figure 2).

3. Attach mud guard to front fender with existing fasteners at locations B and C. Make sure bottom edge of mud guard is parallel to

the ground before tightening fasteners.

4. Using mud guard as a template, mark, center punch, and drill 1/8” holes at locations A and D.

Attach mud guard to fender with #10 screws and washers at locations A and D.

F-150 with flares F-150 without flares and with factory running board

PART NO. 5659 / 5656

5659_5656 Front Instr#1170E.doc

Rev: 1

PAINTING INSTRUCTIONS

1. Clean mud guard with a soap and water solution to remove dirt and other contaminates.

2. Sand painting surface with 320 grit sand paper.

3. Apply a coating of flexible primer-adhesion promoter.

4. Apply a flexible paint as directed by the paint manufacturer.

PAINT PROTECTION FILM - INSTALLATION INSTRUCTIONS

NOTE: The Paint Protection Film is a precut template of film used to protect the mud guard mounting surfaces of your

fenders against wear. The templates (left and right side) can be removed from the backing liner by folding the

liner at the center cut of the template, separating the film sides and peeling the film templates from the backing

liner.

Due to the rock guard on F-150 pickups without fender flares some trimming of the film template will be required for part no.

56561. Simply place film against fender in the mud guard contact area, place mud guard over film and mark where film

needs to be trimmed away from plastic rock guard. Trim film with scissors.

1. Position mud guard on fender to indicate placement location of paint protection film.

2. Clean the placement area of fender with a clean cotton cloth and a petroleum distillate based cleaner such as DuPonts Prep-

Sol Brand Solvent Cleaner or 3M Brand Adhesive Cleaner and dry.

3. Mix a wetting solution of 1 pint of water with 4 drops of liquid dishwashing detergent.

4. Mark correct position of film by placing mud guard against fender.

5. Remove protection film from liner and flood adhesive side of film with wetting solution (use a spray bottle or sponge).

6. Thoroughly wet film placement location of fender with wetting solution.

7. Position the adhesive side of film on fender and flood with wetting solution.

8. Check location of film with mud guard and reposition as necessary.

9. Using a sponge, squeegee any air bubbles and wrinkles from film.

10. Allow film to dry before installing mud guard.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HUSKY LINERS Autozubehör Handbücher

HUSKY LINERS

HUSKY LINERS 47111 Bedienungsanleitung

HUSKY LINERS

HUSKY LINERS X-ACT CONTOUR 53491 Handbuch

HUSKY LINERS

HUSKY LINERS 6334 Handbuch

HUSKY LINERS

HUSKY LINERS 2358 Handbuch

HUSKY LINERS

HUSKY LINERS 2590FR Handbuch

HUSKY LINERS

HUSKY LINERS 47030 Bedienungsanleitung

HUSKY LINERS

HUSKY LINERS 5600 Bedienungsanleitung

HUSKY LINERS

HUSKY LINERS 6510FR Handbuch

HUSKY LINERS

HUSKY LINERS 6147 Handbuch

HUSKY LINERS

HUSKY LINERS 3231 Handbuch

HUSKY LINERS

HUSKY LINERS 5622 Bedienungsanleitung

HUSKY LINERS

HUSKY LINERS 2107 Handbuch

HUSKY LINERS

HUSKY LINERS 6317 Handbuch

HUSKY LINERS

HUSKY LINERS 6582 Handbuch

HUSKY LINERS

HUSKY LINERS 47901 Bedienungsanleitung

HUSKY LINERS

HUSKY LINERS 5730 Bedienungsanleitung

HUSKY LINERS

HUSKY LINERS 47904 Bedienungsanleitung

HUSKY LINERS

HUSKY LINERS 47952 Bedienungsanleitung

HUSKY LINERS

HUSKY LINERS 3402 Handbuch

HUSKY LINERS

HUSKY LINERS 6102 Handbuch

HUSKY LINERS

HUSKY LINERS 5625FR Bedienungsanleitung

HUSKY LINERS

HUSKY LINERS 4713 Bedienungsanleitung

HUSKY LINERS

HUSKY LINERS 2995 Handbuch

HUSKY LINERS

HUSKY LINERS 6077FR Handbuch

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Renault

Renault 77 11 423 180 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung