Husqvarna DS 500 Bedienungsanleitung
DS 500
EN Operator's manual 2-14
ES-MX Manual del usuario 15-27
FR-CA Manuel d’utilisation 28-40
Contents
Introduction..................................................................... 2
Safety..............................................................................3
Assembly........................................................................ 6
Installation.......................................................................7
Operation...................................................................... 10
Maintenance................................................................. 10
Transportation and storage...........................................11
Technical data.............................................................. 13
Service..........................................................................13
Warranty....................................................................... 14
Introduction
Product description
The Husqvarna DS 500 is a drill stand for Husqvarna
drill motors.
• The stand is for drilling in ceilings, walls and floors.
• The drill stand is stable and can be used to drill
dimensions of a maximum diameter of 500 mm.
• The column can be tilted 0-90°.
• The drill stand has a quick mounting plate for the drill
motor.
• The feed lever can be used to set the column tilt and
to lock the quick mounting.
• It is possible to use a 2 m long column (accessory)
on the drill stand.
Product overview
5
6
3
14
13
12
7
9
8
15
17
16
19
18
21
2
1
20
11 10
24
22
23
4
1. Operator's manual
2. Wrench, 24-32 mm
3. Level indicator
4. End stop
2922 - 004 - 27.09.2019
5. Hole for jack screw (accessory)
6. Feed lever
7. Carriage lock
8. Lock screw, column tilt
9. Support
10. Hinge bracket
11. Bottom plate
12. Level adjustment screws
13. Drill column
14. Gear rack
15. Lock clamp, quick mounting
16. Lock screw, lock clamp
17. Carriage
18. Drill column, 2 m (accessory)
19. Transport wheels (accessory)
20. Adapter, quick spacer (accessory)
21. AD bracket (accessory)
22. Connection for vacuum pump
23. Level adjustment screws
24. Gasket, bottom vacuum suction
Symbols on the product
WARNING: This product can be dangerous
and cause serious injury or death to the
operator or others. Be careful and use the
product correctly.
Read the operator's manual carefully and
make sure that you understand the
instructions before you use the product.
Use approved hearing protection.
Note: Other symbols/decals on the product refer to
special certification requirements for some markets.
Product liability
As referred to in the product liability laws, we are not
liable for damages that our product causes if:
• the product is incorrectly repaired.
• the product is repaired with parts that are not from
the manufacturer or not approved by the
manufacturer.
• the product has an accessory that is not from the
manufacturer or not approved by the manufacturer.
• the product is not repaired at an approved service
center or by an approved authority.
Safety
Safety definitions
Warnings, cautions and notes are used to point out
specially important parts of the manual.
WARNING: Used if there is a risk of injury or
death for the operator or bystanders if the
instructions in the manual are not obeyed.
CAUTION: Used if there is a risk of damage
to the product, other materials or the
adjacent area if the instructions in the
manual are not obeyed.
Note: Used to give more information that is necessary in
a given situation.
Always use common sense
WARNING: Under no circumstances should
you modify the original design of the
machine without approval from the
manufacturer. Always use original spare
parts. Unauthorized modifications and/or
accessories may lead to serious injury or
death to the user or others.
It is not possible to cover every conceivable situation
you can face when using a drilling machine. Always
exercise care and use your common sense. Avoid all
situations which you consider to be beyond your
capability. If you still feel uncertain about operating
procedures after reading these instructions, you should
consult an expert before continuing.
Do not hesitate to contact your dealer if you have any
more questions about the use of the machine. We will
willingly be of service and provide you with advice as
well as help you to use your machine both efficiently and
safely.
Let your Husqvarna dealer check the drilling machine
regularly and make essential adjustments and repairs.
All information and all data in the operator’s manual
were applicable at the time the operator’s manual was
sent to print.
Safety instructions for operation
WARNING: Read all safety warnings,
instructions, illustrations and specifications
provided with this power tool. Failure to
follow all instructions listed below may result
in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
922 - 004 - 27.09.2019 3
WARNING: There is always a risk of injuries
when you do work with products that contain
moving parts. Wear protective gloves to
prevent body injuries.
• Use personal protective equipment. Always wear
eye protection. Protective equipment such as a dust
mask, non-skid safety shoes, hard hat or hearing
protection used for appropriate conditions will reduce
personal injuries.
• Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose
control.
• Remove all unwanted materials from the work area
and keep it good illuminated before you start. If the
areas are not cleaned and not illuminated there are
more risks of accidents.
• Do not operate power tools in explosive
atmospheres, such as flammable liquids, gases or
dust. Power tools can make sparks which can set
fire to the dust or fumes.
• Sudden appearance of persons and animals can
make you decrease in control of the product.
Because of this, always concentrate and focus on
the task.
• Do not use the product in bad weather, such as fog,
rain, strong winds, intense cold and equivalent
conditions. Dangerous conditions, such as slippery
surfaces, can occur because of bad weather.
• Examine the work are before you use the product.
Look out for obstacles with risk of sudden and
harmful movement. Make sure that no material can
become loose and fall or cause injury during
operation.
• Always examine the rear side of the surface where
the drill bit will go through the surface. Make the area
safe and put a mark that shows the work area. Make
sure that no injury can occur to persons or material
damaged.
• Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result
in serious personal injury.
• Prevent unintentional starting. Ensure the switch is in
the OFF-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch
or energising power tools that have the switch on
invites accidents
• The product can cause objects to eject, which can
cause injury to the operator. Remove the adjusting
key and wrench before you start the product.
• Do not let familiarity gained from frequent use of
tools allow you to become complacent and ignore
tool safety principles. A careless action can cause
severe injury within a fraction of a second.
• Make sure that all operators, that use the product,
have read and understood the contents of the
operators manual.
• Dress properly. Do not wear loose clothing or
jewellery. Keep your hair and clothing away from
moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts. .
• Dangerous accidents can occur if the concrete core
stay in the drill bit when you pull out the drill motor
from the floor or wall.
• Stay at a distance from the drill bit when the motor is
running.
• Make sure that no pipes or electrical cables are put
in the area where the hole will be made.
• Do not go away from the product when the motor is
running.
• Do not overreach. Keep correct foothold and balance
at all times. This enables better control of the power
tool in unexpected situations.
• Make sure that there is always one more person
close at hand when you use the product. If an
accident occurs, you can receive help when
necessary.
• Do not use a product with defective safety
equipment.
• Do the safety checks, maintenance and service as
given in this manual. Some maintenance and service
measures must only be done by approved service
agents. See the section
Safety devices on the
product on page 5
• Inspection and/or maintenance must be done with
the motor stopped and the plug disconnected from
the power outlet.
• Do not use a product that has been changed from its
factory specification.
• Disconnect the plug from the power source and/or
remove the battery pack, if detachable, from the
power tool before making any adjustments, changing
accessories, or storing power tools. Such preventive
safety measures reduce the risk of starting the
power tool accidentally.
• Keep handles and grasping surfaces dry, clean and
free from oil and grease. Slippery handles and
grasping surfaces do not allow.
• Do not overload the product. If you overload the
product, it can be damaged.
• Keep all parts in good condition and make sure that
all fixtures are correctly tightened.
Personal protective equipment
WARNING: Read the warning instructions
that follow before you use the product.
• Always use correct personal protective equipment
when you operate the product. The personal
protective equipment does not erase the risk of
injury. The personal protective equipment decreases
4922 - 004 - 27.09.2019
the grade of injury if an accident occurs. Let your
dealer help you select the right equipment.
• Use approved eye protection while you operate the
product.
• Use heavy-duty slip-resistant boots with steel toe-
caps.
• Use clothing that is close-fitting but does not limit
your movements.
• Regularly do a check of the condition of the personal
protective equipment.
• Use approved heavy duty protective gloves.
• Use rubber protective gloves to prevent skin irritation
from wet concrete.
• Use an approved protective helmet.
• Always use approved hearing protection while you
operate the product. Noise for a long period can
cause noise-induced hearing loss.
• The product causes dust and fumes that is bad for
your health. Use an approved respiratory protection.
• Make sure that you have a first aid kit near.
• Sparks can occur when you operate the product.
Make sure that you have a fire extinguisher near.
• Do not use loose clothing, jewelry or other items that
can get caught in moving parts. Put your hair up
safely above shoulder level.
Safety devices on the product
WARNING: Read the warning instructions
that follow before you use the product.
• Do not use a product with defective safety devices.
• Do a check of the safety devices regularly. If the
safety devices are defective, speak to your
Husqvarna service agent.
To do a check of the carriage lock
1. Turn the knob to lock the motor carriage.
2. Feel by hand that the carriage is locked to the drill
column.
To do a check of the end stop of the drill column
1. Push the stop plate into the correct position.
2. Make sure that the drill motor carriage stops when it
touches the stop plate.
Safety instructions for maintenance
WARNING: Inspection and/or maintenance
should be carried out with the motor
switched off and the plug disconnected.
• Maintain the product and accessories. Check for
misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the
operation of the product. If damaged, have the
product repaired before use.
• Have your product serviced by a Husqvarna service
dealer using only identical replacement parts.
922 - 004 - 27.09.2019 5
Assembly
Introduction
This section describes how to assemble and adjust the
product.
WARNING: Before you assemble the
product, read the safety chapter and the
assembly instructions.
To attach the wheel kit (accessory)
1. Attach the wheel kit on the rear side of the bottom
plate.
2. Tighten the screw.
To attach the drill motor
WARNING: Always pull out the plug from the
outlet socket before cleaning, maintenance
or assembly.
1. Unlock the drill motor carriage (A).
2. Attach the drill motor in the track (B) on the drill
motor carriage.
3. Lock the drill motor carriage (A).
A
B
Quick spacer (accessory)
Use a quick spacer to drill large hole diameters. To
select the correct quick spacer, refer to
Maximum drill
diameter on page 13
. Assemble the quick spacer on
the drill motor before you attach the drill motor to the drill
stand.
To replace the drill stand column
(assessory)
1. Push the stop plate to open position. Remove the
drill motor carriage.
6922 - 004 - 27.09.2019
2. Fold the drill stand column fully rearward. Refer to
To adjust the angle of the drill column on page 10
.
3. Remove the 4 bolts from the hinge bracket.
4. Remove the drill stand column.
5. Install the drill stand column in the opposite
sequence.
Installation
Procedures for drill stand installation
There are 3 procedures that can be used to attach the
drill stand before a drill operation:
• With an expander bolt.
• With a vacuum plate.
• With a rod that has a thread, a washer and a locknut
To attach the drill stand with an expander bolt
WARNING: When drilling ceilings and walls,
only expander or anchor suitable for
surfaces exposed to tensile forces should be
used. Use only expander or anchor which is
approved for current application.
1. Make a hole for the expander bolt. Refer to
To attach
the expander bolt on page 8
. Measure a distance
(A) of 335 mm (13.2 in.) from the center of the hole
that you will drill. If you use the quick spacer
(assessory), the distance changes. Refer to
Quick
spacer (accessory) on page 6
.
A
2. Attach the bottom plate with an expander bolt.
3. Make sure that the drill stand is tightened correctly.
922 - 004 - 27.09.2019 7
4. If it is necessary, adjust the bottom plate. Use the
level adjustment screws to adjust the bottom plate to
the surface.
To attach the expander bolt
1. Drill a hole for the expander bolt. Make sure that the
depth is sufficient. The socket must be put below the
surface.
2. Use the mandrel and a hammer to install the
expander.
3. Install the anchor screw.
8922 - 004 - 27.09.2019
4. Install the drill stand with the nut.
To attach the product with a Husqvarna
vacuum plate
WARNING: Do not use the product in
combination with the vacuum plate when
you drill in walls or ceilings.
WARNING: The support surface must be flat
and of good quality. The product can
become loose if the vacuum plate cannot
seal fully against the surface.
WARNING: Use of vacuum plate is only
recommended together with these
Husqvarna drill motors: DM 200, DM 220,
DM 230, DM 280, DM 340, DM 400. Use of
other drill motors can cause the product to
become loose.
1. Attach the product to the vacuum plate with the bolt.
2. Loosen the level adjustment screws. They must be
above the bottom of the vacuum plate.
3. Connect the vacuum hose and start the pump.
CAUTION: The minimum pressure must
be -0.85 bar to seal the vacuum plate
tightly to the surface.
4. Tighten the level screws until you feel pressure on
the screw.
WARNING: The level adjustment screws
must touch the surface when when you
use the vacuum plate. If not, the vacuum
plate can come loose.
To attach the drill stand with a rod that has a
thread
Use an all through rod if it is not possible to attach the
drill stand to the wall or ceiling with an expander bolt.
Use washers and nuts to tighten the all through rod.
922 - 004 - 27.09.2019 9
Operation
Before you operate the product
WARNING: This machine is designed for
and intended for drilling concrete, brick and
different stone materials. All other use is
improper.
WARNING: Before drilling, check that all
locking screws are tightened well. Serious
accidents can occur if the concrete core
remains in the drill when backing out the drill
motor/drill from the floor, wall or ceiling.
WARNING: When drilling ceilings, always
use a water collector that is approved for
your drill motor, or use a hydraulic drill
motor. There is a risk that the drilling
machine and the stand become live if water
leaks into the machine.
WARNING: Make sure end stop is fitted and
functional.
1. Read the operator's manual carefully and make sure
that you understand the instructions.
2. Keep the work area clean and bright to prevent
accidents.
3. Do daily maintenance. Refer to
Daily maintenance of
the drill stand on page 10
.
4. Use personal protective equipment. Refer to
Personal protective equipment on page 4
.
To adjust the angle of the drill column
1. Loosen the lock screw that locks the drill column and
set the applicable drill angle.
2. Use the angle indicator for approximate adjustment.
If higher precision is necessary, use alternative
methods to measure.
3. Tighten the lock screw of the drill column. Use the
feed lever. The drill column can be tilted 0-90°.
Maintenance
Introduction
WARNING: Read and understand the safety
chapter before you do maintenance on the
product.
WARNING: To prevent injury, disconnect the
power cord before you do maintenance.
Daily maintenance of the drill stand
• Make sure that the nuts and screws are tight.
• Clean the external surface of the drill stand.
• Make sure that the feed lever moves without
resistance.
• Make sure that the gears move easily and do not
cause a noise.
• Examine the drill column, look for wear or damage.
• Make sure that the drill motor carriage moves easily
and that there is no play against the drill column.
To clean and lubricate the drill stand
CAUTION: If you do not clean the drill stand,
it can become damaged.
1. Remove the drill motor.
2. Clean the drill stand with a high pressure washer
and then remove remaining water with a dry cloth.
3. Lubricate the moving parts on the drill stand. Apply
grease to the contact surfaces to prevent corrosion.
10 922 - 004 - 27.09.2019
Andere Handbücher für DS 500
2
Inhaltsverzeichnis
Sprachen:
Andere Husqvarna Andere Handbücher
