Hussmann Impact M1GLE-93 Bedienungsanleitung

All equipment should be thoroughly examined for

shipping damage before and during unloading.

This equipment has been carefully inspected at

our factory. Any claim for loss or damage must

be made to the carrier. The carrier will provide

any necessary inspection reports and/or claim

forms.

Every effort is made to ship all parts for the kit.

The Hussmann Service Center can be reached by

calling

• from U.S. & Canada 1-800-922-1919 •

• from Mexico 1-800-522-1900 •

Merchandisers

M1GLE-93

Joining

Back-to-Back

PARTS LIST

(One Joining Kit per Two M1GLE-93)

Item Quantity Description

1. 6 Screw – Phillips Head – #8-18 x 1/2

2. 2 Gasket Tape 1 x 1/2 x 180

3. 2 Cap Screw 5/16 -18 x 3 1/2in.

4. 8 Flat Washer 5/16

5. 4 Lock Washer 5/16

6. 4 Hex Nut 5/16 -18

7 2 Cap Screw 5/16 -18 x 5 1/2in.

8. 1 Silicone Sealer

9. 1 Top Trim – 10 1/2in. x 84-in.

10. 2 Top Rail Trim

11. 2 Bumper – Top (CUT TO FIT)

12. 2 Bumper – Bottom (CUT TO FIT)

13. 8 Bracket — End Splashguard

14. 20 Screw – SM Hex Head – TEK2 – #8-18 x 1/2

15. 2 Splashguard Support

P/N 0503478_A

April 2008

U.S. & CANADA 1-800-922-1919 • MEXICO 1-800-522-1900 • WWW.HUSSMANN.COM

JOINING BACK-TO-BACK

Joining two end case requires

different parts and procedures

than are used to join an end

case to a line-up. Please follow

these instructions to assure

satisfactory performance, fit

and finish.

1On the back of each case,

replace screws and

remove studs.

Replace all 1/4in. Hex

head screws on the back

of each case with

Phillips Head Screws – 1

supplied.

Remove (or cut flush) the

studs used in normal case

joining.

2Position first case.

All cases must be level to

ensure correct operation.

Place the first case in

position, then check for

level front-to-back and

side-to-side. Use the

provided metal shims to

level the case. Place shims

under front and back rail

at cross-members.

Figure 1 — Remove Studs and Replace Screws

P/N 0503478_A

2U.S. & Canada 1-800-922-1919 • Mexico 1-800-522-1900 • WWW.HUSSMANN.COM

Figure 2 — Position and Level First Case

Levels

Serial Plate

3Remove the honeycomb

as shown in Figure 3.

4Lift up and out to remove

the interior back panels.

Refer to Figure 4 for

location.

M1LGE-93 Joining P/N 0503478_A

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. • WWW.HUSSMANN.COM

Figure 4 — Remove Interior Back Panels

Interior

Back Panels

Figure 3 — Remove Honeycomb

Honeycomb

5Insert Alignment Pins

Each case ships with

alignment pins that are

inserted in end frames or

other mating surfaces to

facilitate positioning.

Refer to Figure 5 for

correct placement.

6Apply Gasket

Apply Gasket – 2 as

indicated in Figure 5.

Gasket should be inset

1/4-in from edge, and

extend up the sides to the

glass.

The same gasket arrange-

ment is used both cases.

Assure good adhesion of

gaskets by wiping the end

frame with rubbing alcohol

to remove any accumulated

dust and oils.

Apply silicone sealant

above gasket as shown in

Detail

Remove paper backing

before proceeding to next

step.

P/N 0503478_A

4U.S. & Canada 1-800-922-1919 • Mexico 1-800-522-1900 • WWW.HUSSMANN.COM

Figure 5 — Apply Gaskets

1 in. Gasket

(24 mm) Insert

Alignment Pins

Insert

Alignment

Pins

Apply Gasket up to

Glass onEach Side

IMPORTANT

• Do not stretch gasket, especially around corners.

• Do not butt gaskets; always overlap them as shown.

• Remove paper backing after gasket has been applied.

• Perimeter gasket required by NSF.

A continuous bead of

silicone sealant/ caulk

may be used in addition

to gaskets on mating

surfaces but must not be

used in lieu of gaskets.

Detail

7Position Second Case

Alignment pins guide the

mating of the frames.

Insert Cap Screw – 3

through Flat Washer – 4,

then through frame

into nut retainer.

Add Flat Washer –- 4,

Lock Washer –- 5 and

Hex Nut – 6. Tighten to

draw side frames together.

8From the front of one case,

use a long (10 1/2in.) bit to

drill a 3/8in. hole in each

end frame behind honey-

comb. Drill through both

cases. On each side, insert

Cap Screw – 7 through

Flat Washer –- 4, then

through both frames.

Add Flat Washer –- 4,

Lock Washer –- 5 and

Hex Nut – 6. Tighten to

draw frames together only

until space between PTM

measures 10 1/4inches.

ANYTHING LESS THAN

10 1/4 INCHES WILL

DAMAGE THE CASES.

M1LGE-93 Joining P/N 0503478_A

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. • WWW.HUSSMANN.COM

Figure 7 — Location of Cap Screws in Side Frames

Figure 8 — Drill Holes in Back Frame

Figure 6 — Move Second Case

Cap Screw

Metal

Washer

Lock

Washer

Nut

Metal

Washer

Case

Frames

31/2-inch

51/2-inch

Minimum 10 1/4inches between PTM

10 1/4

8Use Silicone Sealer – 8

inside to seal the 1-inch

gap between end frames

as shown in Figure 9.

Apply Silicone Sealer – 8

over Cap Screws – 3, over

Cap Screws – 5, and over

Hex Nuts – 7.

9Adjust color panels on

each side to minimize

any gaps.

P/N 0503478_A

6U.S. & Canada 1-800-922-1919 • Mexico 1-800-522-1900 • WWW.HUSSMANN.COM

Figure 9 — Apply Silicone

10 From one side, slide

Top Trim – 9 under

price tag moldings on top

of cases to cover gap as

shown in Figure 10.

11 Remove the protective

film from the stainless

steel top rail, then install

the Top Rail Trim – 10

on each side as shown in

Figure 12.

M1LGE-93 Joining P/N 0503478_A

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. • WWW.HUSSMANN.COM

Figure 10 — Install Top Trim

Figure 11 — Install Top Rail Trim

Top Rail Trim

Top Trim

Top Rail Trim

13 The top and bottom

bumpers should be

kept inside a cooler or

refrigerated case for at

least six (6) hours. This

will allow the bumper to

contract.

Remove all remaining

shipping braces. Measure

and cut Top Bumper – 11

and Bottom Bumper – 12.

Use a miter box and fine-

tooth saw to cut bumpers

to length. Install the top

and bottom bumpers.

Remove protective film

from the bumpers once

installation is complete.

14 Replace interior back

panels.

Replace honeycomb and

retainers as shown in

Figure 15.

P/N 0503478_A

8U.S. & Canada 1-800-922-1919 • Mexico 1-800-522-1900 • WWW.HUSSMANN.COM

Figure 13 — Remove Braces and Install Bumpers

Honeycomb

Figure 15 — Replace Honeycomb

Figure 14 — Remove Protective Film

Miter Box

Bumper

Shipping

Braces

Shipping

Braces

15 Attach the Splashguard

Brackets – 13 to side of

legs using Screws – 14.

Attach Splashguard Joint

Supports – 15 using

Screws – 14. Refer to

Figure 16.

16 Install splashguards.

Adjust to minimize

any gap at joint.

1. Check to be sure that all

splashguard brackets are

level with the floor.

2. Position top of splashguard

over the top edge of the

bracket as shown below.

3. Push the lower edge of the

splashguard toward the bot-

tom of the bracket until it

snaps into place.

M1LGE-93 Joining P/N 0503478_A

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. • WWW.HUSSMANN.COM

Figure 16 — Install Splashguard Brackets

Joint Support

Screw

Splashguard

Brackets

Figure 17 — Install Splashguards

Splashguard

Bracket Base of

Case

Splashguard

Andere Handbücher für Impact M1GLE-93

Inhaltsverzeichnis

Andere Hussmann Kaufmann Handbücher

Hussmann

Hussmann IMPACT M4NE Bedienungsanleitung

Hussmann

Hussmann Impact Excel C2X-LGEP Bedienungsanleitung

Hussmann

Hussmann IMPACT D5RRI Kurzanleitung

Hussmann

Hussmann LN Bedienungsanleitung

Hussmann

Hussmann C2XEC-XE Bedienungsanleitung

Hussmann

Hussmann IMPACT RL Bedienungsanleitung

Hussmann

Hussmann IMPACT M1CIMP-4B Bedienungsanleitung

Hussmann

Hussmann LBN Kurzanleitung

Hussmann

Hussmann ARV-570 Bedienungsanleitung

Hussmann

Hussmann VBL Bedienungsanleitung

Hussmann

Hussmann IMPACT Elite E2V Bedienungsanleitung

Hussmann

Hussmann G5 Kurzanleitung

Hussmann

Hussmann SI3E Bedienungsanleitung

Hussmann

Hussmann BCH Bedienungsanleitung

Hussmann

Hussmann CGDM Bedienungsanleitung

Hussmann

Hussmann FWEG Bedienungsanleitung

Hussmann

Hussmann EVM Kurzanleitung

Hussmann

Hussmann PWE Bedienungsanleitung

Hussmann

Hussmann RGSSFP Bedienungsanleitung

Hussmann

Hussmann IMPACT Elite E1S Bedienungsanleitung

Hussmann

Hussmann Impact Excel C6X-LE Bedienungsanleitung

Hussmann

Hussmann RCD Bedienungsanleitung

Hussmann

Hussmann Impact C2-LGEP Bedienungsanleitung

Hussmann

Hussmann IMPACT ED1 Bedienungsanleitung

Beliebte Kaufmann Handbücher anderer Marken

FRIGOGLASS

FRIGOGLASS Flex 20 HC Bedienungsanleitung

EPTA

EPTA COSTAN RHINO MULTI Bedienungsanleitung

CASCO

CASCO Nano Cube Bedienungsanleitung

True

True GDIM-26 Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis Mobile Series Montageanleitung

Haussmann

Haussmann RL Bedienungsanleitung

Howard McCray

Howard McCray R-CDS32E-4 Bedienungsanleitung

EPTA

EPTA iarp Cool Emotions Delight Lite Bedienungsanleitung

VALERA

VALERA BC 85 Bedienungsanleitung

HL Display

HL Display 3eBin Bedienungsanleitung

Dixie Narco

Dixie Narco DNCB 501E Bedienungsanleitung

APW Wyott

APW Wyott Racer DMXD-30H Bedienungsanleitung

Hoshizaki

Hoshizaki KD-90C Bedienungsanleitung

Summit

Summit SCR1006 Bedienungsanleitung

Delfield

Delfield Shelleyspeed SPM-28E Bedienungsanleitung

EPTA

EPTA iarp Cool Emotions GLEE 40 Bedienungsanleitung

Kysor/Warren

Kysor/Warren GranBering KW Leitfaden

Crane

Crane BevMAX Refresh 6 Media Bedienungsanleitung