Hussmann SPECIALTY TY3-3X4.5E-R Bedienungsanleitung

/SPECIALTY

TY3/4 ISLAND

MERCHANDISER

USER MANUAL

042023

TY3 ‐TY3‐3X4.5E‐R

‐TY3‐3X5.5E‐R

‐TY3‐3X4.5E‐S

‐TY3‐3X4.5E‐S

TY4 ‐TY4‐3X4.5E‐R

‐TY4‐3X5.5E‐R

1. General Instructions

A publication of HUSSMANN®Chino

13770 Ramona Avenue • Chino, California 91710

(909) 628-8942 FAX

(909) 590-4910

(800) 395-9229

www.hussmann.com

This Booklet Contains Information on:

TY3W COLD ISLAND SELF SERVICE CASE

A Multi-deck, spot merchandisers designed for medium temperature applications such

as: Deli/Dairy/Beverage. They are available as either remote type models, which require

separate condensing unit connections, or self-contained models. Each self-contained

model will have it’s own condensing unit, factory installed beneath the display area of

the case ready for operation on when electrical service is connected.

Shipping Damage

All equipment should be thoroughly examined for shipping damage before and during

unloading.

This equipment has been carefully inspected at our factory and the carrier has assumed

responsibility for safe arrival. If damaged, either apparent or concealed, claim must

be made to the carrier.

Apparent Loss or Damage

If there is an obvious loss or damage, it must be noted on the freight bill or express

receipt and signed by the carrier’s agent; otherwise, carrier may refuse claim. The

carrier will supply necessary claim forms.

Concealed Loss or Damage

When loss or damage is not apparent until after equipment is uncrated,aclaimfor

concealed damage is made. Make request in writing to carrier for inspection within 15

days, and retain all packaging. The carrier will supply inspection report and required

claim forms.

Shortages

Check your shipment for any possible shortages of material. If a shortage should exist

and is found to be the responsibility of Hussmann Chino, notify Hussmann Chino.If

such a shortage involves the carrier, notify the carrier immediately, and request an

inspection. Hussmann Chino will acknowledge shortages within ten days from receipt

of equipment.

Hussmann Chino Product Control

The serial number and shipping date of all equipment has been recorded in Hussmann’s

files for warranty and replacement part purposes. All correspondence pertaining to

warranty or parts ordering must include the serial number of each piece of equipment

involved, in order to provide the customer with the correct parts.

Keep this booklet with the case at all times for future reference.

2.Table of Contents

1. General Instructions...............................................................2

2. Table of Contents ...................................................................3

3. Warning ...................................................................................4

4. Cut and Plan View ..................................................................5

5. Notice.......................................................................................6

6. Installation...............................................................................7

7. Electrical …………………………………………………………12

8. Wiring Diagram Index............................................................13

9. Wiring Diagrams ………………………………………………..15

10. Spec Sheet ...........................................................................56

11. Parameter Report ................................................................58

12. Danfoss Controller…….......................................................60

13. Dixell Controller …………………………………………….…61

14. Troubleshooting Guide .......................................................62

15. Maintenance..........................................................................66

16. Appendices ..........................................................................67

3. Warning

Please read these instructions completely

before beginning case installation

1. Do not push, pull, adjust or manipulate the merchandiser

by any glass component.

• Doing so will result in severe damage to such compo-

nents.

• Glass or acrylic breakage may result in serious

injury.

• See lifting and transport instructions for proper

moving technique ref. pg 10.

2. Never stand on the merchandiser top, deck, or any

shelves for any reason. These surfaces are not steps and

are not designed to support such loads.

• Misusing these surfaces as steps will result in dam

age to the case and or serious injury to the user

• These surfaces are intended for the storage and

merchandising of food products

• Use a ladder or designed structure to work above

the case (Do not lean on case)

IMPORTANT

INFORMATION

Shelves - optional

Angled Shelf Insert

-optional

321/2 (826)

281/2 (724)

361/8 (918)

381/8 (968)

10 (254)

113/4

(298)

241/4

(616)

201/4

(514)

575/8

(1464)

273/8

(695)

291/8

(740)

Shelves - optional

Angled Shelf Insert

-optional

321/2 (826)

281/2 (724)

361/8 (918)

381/8 (968)

10 (254)

113/4

(298)

341/4

(870)

201/4

(514)

675/8

(1718)

273/8

(695)

291/8

(740)

base close-off

34 (864)

max

46 (1168)

max

6min

(152)

19 max

(483) 661/2 (1689)

“B”

“A”

“A” 541/2 (1384)

4.5' 5.5'

(25)

281/2

(724)

361/8

(918)

381/8

(968)

open to floor

4. Cut and Plan Views

5. Notice

NOTICE

Do NOT remove Foam Blocks from shelves

and glass until the merchandisers are

positioned for installation. Shelves or

merchandising glass may be damaged.

Loose

Items

Warning

Labels

Foam Blocks

in place Boards

fastened

Case is to arrive at store as was shipped form factory. See

reference above for proper shipment referencing. (Not

actual case)

Receiving Case

Upon receiving your new Hussmann Case all equipment

should be thoroughly examined for shipping damage be-

fore and during unloading. This equipment has been care-

fully inspected at our factory. Any claim for loss or damage

must be made to the carrier. The carrier will provide any

necessary inspection reports or claim form.

If there is obvious loss or damage, it must be noted on the

freight bill or express receipt and signed by the carrier’s

agent; otherwise carrier may refuse claim.

6. Installation

Do Not Install the Vented Panels of the

self-contained model against a wall or

other storage fixture.

Located in the lower front and rear of the self-contained

models are vented panels. These panels allow air circulation

to the condensing unit. Blocking or restricting air circulation

through these panels can cause poor performance and

damage the refrigeration system.

Exterior Loading

These models have not been structurally designed to support

excessive external loading. Do not walk on their tops;

This could cause serious personal injury and damage to

the fixture.

It is the contractor’s responsibility to install

case(s) according to local construction and

health codes.

ATTENTION

INSTALLER

Levelling

A LEVEL CASE IS NECESSARY TO INSURE

PROPER OPERATION AND WATER DRAINAGE.

Note: To avoid removing concrete flooring, begin

lineup leveling from the highest point of the store

floor.

Store Conditions

• Case is designed to operate at temperatures at either

75°F at 55% relative humidity or 80°F at 55% relative

humidity. Case must be kept in that environment to

ensure case performance and product safety.

• Do not position the case near an HVAC vent.

• Do not position the case near an entrance door. Outside

ambient conditions may have an adverse affect on the

refrigeration performance, a minimum of 15’ clearance is

required from doors.

• Do not position the case tight against a ceiling or soffit.

A minimum clearance 10” above the unit is required for

proper compressor discharge air flow.

• Do not block case front panel vent (supplies critical

intake air flow to the compressor)

BEFORE SERVICING

ALWAYS DISCONNECT ELECTRICAL

POWER AT THE MAIN DISCONNECT

WHEN SERVICING OR REPLACING ANY

ELECTRICAL COMPONENT.

This includes (but not limited to) Fans, Heaters

Thermostats, and Lights.

Uncrating the Stand

Place the fixture as close to its permanent position as

possible. Remove the top of the crate. Detach the walls from

each other and remove from the skid. Unbolt the case from

the skid. The fixture can now be lifted off the crate skid. Lift

only at base of stand!

Minimum Clearances for Self-Contained cases are to be

followed as instructed for proper placement inside store

locations.

• Intake and exhaust clearances are to be a minimum of

8’ when placed next to a solid wall.

• Height clearance measured from floor follows as a

minimum of 10’ vertically.

• Minimum of 36” clearance if near an open aisle is

required for proper cycle ventilation. (Assumed 8’

clearance from solid wall)

8’ clearance

Installation (Cont’d)

Condensate Pan Setup and Maintenance Clearances

Setup:

There are two condensate evaporator pans on this unit. The

drain pipes from the case feed into the Condensate Pan.

This condensate pan will turn on when the float switch level

is triggered. If the volume of water is above the capacity of

this pan, excess water will flow into the “Secondary Con-

densate Pan”. Both the Primary and Secondary conden-

sate pans are placed into a metal receiver. The metal

receiver is there to collect excess water that may overspill

in case of (a) failure of the condensate pans or (b) store

conditions being above design specification causing more

condensate water to be formed than expected.

Maintenance:

Care must be taken to ensure that the condensate pans

operate properly at the store. These units are designed to

operate at either 75°F ambient and 55% RH or 80°F ambi-

ent and 55% RH. If stores are operating above this condi-

tion, case performance will be severely affected. If such a

condition is noted, the metal receiver under the condensate

pans must be checked periodically to see if excess water is

being collected. If water has accumulated, water must be

siphoned out of the receiver. Care must be taken while per-

forming this step. Unit power should be shut off for electrical

safety. Once water has been removed and metal receiver is

dried out, unit power can be turned back on.

Condensate Pan

Close-off Removal

The side close-off panels are held in place by upper and

lower tabs located on the underside of the tub and bottom

base channel near the bottom of the case. See image

below for exact close-off tab locations.

Closeoff Tabs

Slide bottom of close-off in upward motion to remove

close-off panel slots from lower close-off tabs.

Step 2

Pull Close-off in outward then downward motion to com-

pletely remove side panel close-off

BEFORE SERVICING

ALWAYS DISCONNECT ELECTRICAL

POWER AT THE MAIN DISCONNECT

WHEN SERVICING OR REPLACING ANY

ELECTRICAL COMPONENT.

This includes (but not limited to) Fans, Heaters

Thermostats, and Lights.

Once Close-off panel is removes, this now provides ac-

cess to internals such as condensing unit, evap pan and

electrical junctions.

To replace close-off panels, simply reverse the listed steps.

Installation (Cont’d)

Step 1

Installation (Cont’d)

Entyce Lifting and Transporting Instructions

Lift Zone (Approximate)

J-Bar

Lift Point

J-Bar

Lift Point

J-Bar

Lift Point

J-Bar

Lift Point

J-Bar

Lift Point

J-Bar

Lift Point

1. The Entyce can be lifted by a forklift only at the specified location in the diagram

Improper placement of forks may damage

drainage piping. Use a spotter when placing forks.

Make sure that piping will not be damaged.

Use J-Bars or Jacks if Forks cannot be used safely

2. Remove close-offs and lower body panels before lifting with a fork. Serious damage will occur if the body panels are not

removed.

• Remove the end case lower and bottom panels first

• Then remove the side case lower and bottom panels

3. Make sure that fork spacing and width will not damage drain, piping, or electrical lines.

4. Be sure that the forks are long enough to support beyond the center of the case. Check for proper balance before

moving. A minimum fork length of 36” is recommended for 68” wide cases.

5. The Entyce can be raised at one end with a forklift to allow the placement of rollers or dollies.

6. Never drag or push the Entyce by ANY COMPONENT including ANY GLASS COMPONENT. This will result in damage

to the base, and possibly damage to other components.

7. Evenly support the entire base structure on rollers or dollies before attempting to move. Each Base Leg must have its

own dollie to properly support the case.

WARNING

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hussmann Kaufmann Handbücher

Hussmann

Hussmann IMPACT D5RRI Bedienungsanleitung

Hussmann

Hussmann Impact Excel M5EP Bedienungsanleitung

Hussmann

Hussmann IMPACT D5NLE Bedienungsanleitung

Hussmann

Hussmann Q1-SS Betriebsanleitung

Hussmann

Hussmann Elite Series Bedienungsanleitung

Hussmann

Hussmann M62 Bedienungsanleitung

Hussmann

Hussmann SGB Bedienungsanleitung

Hussmann

Hussmann C2NX-XLGE Bedienungsanleitung

Hussmann

Hussmann C2X-XEP Bedienungsanleitung

Hussmann

Hussmann Impact Excel M5X Handbuch

Hussmann

Hussmann RID Betriebsanleitung

Hussmann

Hussmann Impact Excel M1X-E Bedienungsanleitung

Hussmann

Hussmann IMPACT M4G Bedienungsanleitung

Hussmann

Hussmann G5 Bedienungsanleitung

Hussmann

Hussmann RCD Betriebsanleitung

Hussmann

Hussmann GSVM4060F Bedienungsanleitung

Hussmann

Hussmann SMG Bedienungsanleitung

Hussmann

Hussmann SMBV Bedienungsanleitung

Hussmann

Hussmann CGDM Bedienungsanleitung

Hussmann

Hussmann ISFGG Kurzanleitung

Hussmann

Hussmann C2XEC-XE Bedienungsanleitung

Hussmann

Hussmann FNGSC-A Bedienungsanleitung

Hussmann

Hussmann C6L-EP Bedienungsanleitung

Hussmann

Hussmann Specialty ProductsCR3FO Bedienungsanleitung

Beliebte Kaufmann Handbücher anderer Marken

FRIGOGLASS

FRIGOGLASS Flex 20 HC Bedienungsanleitung

EPTA

EPTA COSTAN RHINO MULTI Bedienungsanleitung

CASCO

CASCO Nano Cube Bedienungsanleitung

True

True GDIM-26 Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis Mobile Series Montageanleitung

Haussmann

Haussmann RL Bedienungsanleitung

Howard McCray

Howard McCray R-CDS32E-4 Bedienungsanleitung

EPTA

EPTA iarp Cool Emotions Delight Lite Bedienungsanleitung

VALERA

VALERA BC 85 Bedienungsanleitung

HL Display

HL Display 3eBin Bedienungsanleitung

Dixie Narco

Dixie Narco DNCB 501E Bedienungsanleitung

APW Wyott

APW Wyott Racer DMXD-30H Bedienungsanleitung

Hoshizaki

Hoshizaki KD-90C Bedienungsanleitung

Summit

Summit SCR1006 Bedienungsanleitung

Delfield

Delfield Shelleyspeed SPM-28E Bedienungsanleitung

EPTA

EPTA iarp Cool Emotions GLEE 40 Bedienungsanleitung

Kysor/Warren

Kysor/Warren GranBering KW Leitfaden

Crane

Crane BevMAX Refresh 6 Media Bedienungsanleitung