Hytronik HMW32 Bedienungsanleitung

Daylight Harvest with Remote Control

IP65 High Bay HF Motion Sensor

IP65RED

Stand-by power

EMC standard (EMC)

Safety standard (LVD)

Radio Equipment (RED)

Resistive

EN55015, EN61000

Semko, CB, CE , EMC, RED, RCM

EN60669-1, EN60669-2-1

Model No.HMW32

120 ~277VAC 50/60Hz

Mains voltage

Load ratings:

EN300440, EN301489-1,

EN62479

<1W

Input Characteristics

Safety and EMC

400VA@120V; 800VA@220 -277V

800W@120V; 1600W@220 -277V

Capacitive

Sensor Data

HMW32

Operation temperature

Ta: -20

C ~ +70

Environment

IP65

IP rating

Model No.

<0.2mW

5.8GHz +/- 75MHz

High Frequency (microwave)Sensor principle

Operation frequency

Transmission power

Detection range

Detection angle

Max. ( Ox H) 10m x 15m

20sWarming-up

Technical Data

360 O

Mechanical Structures and Installations

For more details, please refer to user manual.

A. Ceiling mount

Sensor module

Photocell

LED indicator

Infrared receiver

Rotary switch Cable entry

Installation rack

91.5

59.3

57.3

47.5

4.1

80.7

4.1

66.6

81.5

Inf

Intelligent Photocell (daylight detection prior to motion detection)

The built-in photocell will also automatically turn o the light when the ambient natural light exceeds the programmed lux level for

stays at

dimmed level during absence.

switches on the light automatically when

presence is detected.

does not switch on when presence is

detected.

The sensor switches o the light when

presence.

Functions and Features

C. Attach to the shade by clamp

B. Screw to the Luminaire by conduit

Photocell

Sensor module

Photocell

LED indicator

Infrared receiver

Rotary switch

Angle adjustment

Luminaire clamp

Sensor module

LED indicator

Infrared receiver

Rotary switch

Cable entry

59.6

66.6

89.9

0.825”

59.3

57.3

35.2

47.5

84.5

59.3

47.5

66.6 80

146.6

ht, the li

es notswitchonwhen presence

ht, the

itches on thelight automatically

he sensor switches o the li

Daylight Harvest

Light will not switch on

when natural light is

motion detected.

The light switches on

automatically with

presence when natural

The light turns on at full or dims to maintain the lux level. The light output

regulates accroding to the level of natural light available.

The light dims to stand-by

period after hold-time and

stays on selected minimum

dimming level.

The light switches o when

the ambient natural light is

The light switches o

completely after the

stand-by period.

Note:

The Light automatically dims down and

eventually turns o if the natural light lux

level exceeds the daylight threshold.

However, if the stand-by period is preset

but dim to minimum level, even the

zero-cross point

Alternating current

Zero-cross Relay Operation

Designed in the software, sensor switches on/o the

load right at the zero-cross point, to ensure that the

in-rush current is minimised, enabling the maximum

lifetime of the relay.

A rotary switch is built inside the sensor for scene

selection / fast programming. Total 16 channels

are available:

Rotary switch preset

Rotary Switch Preset

Note: settings can also be changed by remote control

HRC-11.The last action controls.

0 5s100% Disable

nim11 100% 50Lux

nim52 100% 50Lux

nim53 100% 75Lux

nim54 100% 100Lux

nim55 100% 200Lux

nim016 100% 50Lux

nim017 100% 75Lux

nim018 100% 100Lux

nim019 100% 200Lux

nim02A 100% 100Lux

nim02B 100% 200Lux

C 30min100% 100Lux

nim03D 100% 200Lux

E30min100% 400Lux

F5s100%

10%

30%

10%

30%

10%

30%

10%

30%

50%

10%100Lux

10s

5min

10min

+∞

30min

+∞

10s

Detection

range

Channel Hold-time Stand-by

time

Stand-by

dim level

Daylight

sensor

1. Press button “Shift”, the red LED is on for indication.

2. Press button “Sensor o”, the function of movement detection is disabled.

Settings (Remote Control HRC-11)

HRC-11

Press button “RESET”, all settings go back to rotary switch settings.

Reset Settings

Permanent ON/OFF function

Press button “ON/OFF” to select permanent ON or permanent OFF mode.

* Press button “AUTO”, “RESET” to quit this mode.

ON/

OFF

Sensor o (Daylight harvest without occupancy)

Press the buttons to select light output at 80% (at initial 10,000 hours) or 100%.

Note: “Twilight” function is disabled.

Power output

Load Indication:

receiving the commamd from the

remote control successfully.

AUTO mode

Press button “AUTO” to initiate automatic mode. The sensor starts working and all

settings remain as before the light is switched ON/OFF.

Note: “Semi-auto” function is disabled.

Press the buttons to adjust the light brightness to reset the target lux level.

Brightness +/-

Scene program - 1-key commissioning

Detection range

Press buttons in zone “Detection range” to set detection range at 100% / 75% / 50% / 10%.

1. Press button “Start” to program.

2. Select the buttons in “Detection range”, “Daylight threshold”, “Hold-time”, “Stand-by time”, “Stand-by dimming level” to setall

parameters.

3. Press button “Memory” to save all the settings programmed in the remote control.

4. Press button “Apply” to set the settings to each sensor unit(s).

For example, to set detection range 100%, daylight threshold Disable, hold-time 5min, stand-by time +∞, stand-by dimming level 30%, the steps should be:

Press button“Start”, button ”100%”, “Disable”, “Shift”,“5min”, “Shift”, “+∞”, “30%”,“Memory”. By pointing tothe sensor unit(s) and pressing “Apply”, all

settings are passed on the sensor(s).

Press button “Shift”, the LED on the top left corner is on to indicate mode selection.

All values / settings in RED are valid for 20 seconds.

Shift Button

Press buttons in zone“ Daylight threshold” to set daylight sensor / target lux level at 50Lux / 100Lux / 300Lux / 500Lux / Disable.

Note: 2lux / 10lux are disabled.

Daylight threshold

2. Press button “Ambient”, the surrounding lux level is sampled and set as the new daylight threshold / target lux level.

Ambient daylight threshold

Hold-time

Press buttons in zone “hold-time” to set the hold-time at 2s / 30s / 1min / 5min / 10min / 15min / 20min / 30min.

2. 2s is for testing purpose only, stand-by period and daylight sensor settings are disabled in this mode.

*To exit from Test mode, press button “RESET” or any button in “Hold-time”.

Dual tech & RF mode

Stand-by dimming level

Stand-by time (corridor function)

Press buttons in zone “stand-by time” to set the stand-by period at 0s / 10s / 1min / 5min / 10min / 30min / 1h / +∞.

at thestand-by dimming level

whenno presence after motion hold-time.

Press the button in zone “stand-by dimming level” to set the stand-by dimming level at 10% / 20% / 30% / 50%.

All buttons are disabled.

Wiring Diagram

Detection Pattern

Ceiling mounted height(m)

10%

30%

75%

50%

HMW32

Brown

LED driver

1-10V+

1-10V

Blue

Grey

Red

Black

2. Select a time period and the sensor will do light level measurement and determine/save the lowest light level (commission line)

with 100% light on, so as to set the target lux level automatically.

Note: 1. Make sure the light level measurement covers the night time.

Inhaltsverzeichnis

Andere Hytronik Zubehör Handbücher

Hytronik

Hytronik HC005S/BT Kurzanleitung

Hytronik

Hytronik HMW38/RF Bedienungsanleitung

Hytronik

Hytronik HN020-01V Bedienungsanleitung

Hytronik

Hytronik HCD418/I Bedienungsanleitung

Hytronik

Hytronik DUAL SENSE HIM11 Kurzanleitung

Hytronik

Hytronik DUAL Sense HIM13 Kurzanleitung

Hytronik

Hytronik HIM32 Kurzanleitung

Hytronik

Hytronik HIR28 Kurzanleitung

Hytronik

Hytronik HC404VRC-KD Bedienungsanleitung

Hytronik

Hytronik HMW30 Bedienungsanleitung

Hytronik

Hytronik HC403VRC-KD/I Bedienungsanleitung

Hytronik

Hytronik HC019V/DH Bedienungsanleitung

Hytronik

Hytronik HC005S/I Kurzanleitung

Hytronik

Hytronik Dual Sense HIM11 Bedienungsanleitung

Hytronik

Hytronik HMW23 Bedienungsanleitung

Hytronik

Hytronik HMW31 Kurzanleitung

Hytronik

Hytronik HIM30 Bedienungsanleitung

Hytronik

Hytronik HBIR30/CA Kurzanleitung

Hytronik

Hytronik HIM38/RF Bedienungsanleitung

Hytronik

Hytronik HEC9025/I Kurzanleitung

Hytronik

Hytronik HMW12 Kurzanleitung

Hytronik

Hytronik HC407VDS Bedienungsanleitung

Hytronik

Hytronik SensorDIM HEC7030 Bedienungsanleitung

Hytronik

Hytronik HIM32 Kurzanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung