IBM 5147-084 Bedienungsanleitung

IBM ESS expansion

Version 5.1

Installation and User Guide - Model

084

SC27-4628-01

IBM

Note

Before using this information and the product it supports, read the following information:

vThe general information in “Notices” on page 57

vThe information in the “Safety and environmental notices” on page ix

vThe information in the IBM Environmental Notices and User Guide (provided on a DVD)

This edition applies to IBM ESS expansion Model 084 and is valid until replaced by new editions.

US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract

with IBM Corp.

Contents

Figures ............... v

Tables ............... vii

Safety and environmental notices ... ix

Safety notices .............. ix

Environmental notices .......... xiv

Support information ......... xv

Chapter 1. Appliance safety precautions 1

Introduction .............. 1

Damage ................ 1

Handling ............... 1

Operation ............... 3

Electrical safety ............. 5

Rack system safety precautions ........ 7

Electrostatic discharge (ESD) precautions ..... 8

Regional safety ............. 8

Chapter 2. System overview ...... 9

Chassis ................ 9

The enclosure core product ......... 10

Enclosure Chassis ............ 11

Power supply unit (PSU) .......... 15

Cooling module ............. 16

SBB I/O module............. 17

Enclosure management .......... 18

Chapter 3. Installation ........ 19

Preparation .............. 19

Installation .............. 20

Power cord connection .......... 22

Grounding checks ............ 23

System Configurations........... 23

Data security .............. 23

Chapter 4. Operation......... 25

Before you begin ............ 25

Power on ............... 25

Ops panel LEDs ............. 26

Unit identification number ......... 26

Normal Power down ........... 27

Locking drawers............. 27

Chapter 5. Troubleshooting ...... 29

Initial start-up problems .......... 29

LEDs ................ 29

Thermal sensors ............. 35

Troubleshooting ............. 35

Dealing with hardware faults ........ 36

Firmware Updates ............ 36

Chapter 6. Module replacement .... 37

Overview ............... 37

General procedures ............ 37

Replacing a disk drive in carrier (DDIC)..... 39

Replacing a cooling module ......... 42

Replacing a power supply unit (PSU)...... 44

Replacing an SBB I/O module ........ 46

Appendix A. Technical specifications 49

Dimensions .............. 49

Weights................ 49

Components (fully populated) ........ 49

Thermal ............... 50

Temperature and humidity ......... 50

Cooling modules ............ 50

SBB I/O module............. 50

Power supply unit (PSU) .......... 50

Supported drives ............ 51

Shock and vibration tolerance ........ 51

Appendix B. Standards and regulations 53

EMC qualification ............ 53

Safety ................ 54

Environmental and Recycling ........ 54

Acoustics ............... 56

AC power cords ............. 56

Potential for radio frequency interference .... 56

Notices .............. 57

Trademarks .............. 58

Electronic emission notices ......... 59

Federal Communications Commission Statement 59

Industry Canada Compliance Statement .... 59

Australia and New Zealand Class A Statement 59

European Union Electromagnetic Compatibility

Directive .............. 59

Germany Electromagnetic Compatibility Directive 60

People's Republic of China Class A Statement .. 61

Taiwan Class A Statement ........ 61

Taiwan Contact Information ........ 61

Japan Electronics and Information Technology

Industries Association (JEITA) Notice ..... 61

Japan Voluntary Control Council for Interference

(VCCI) Notice ............ 62

Korean Communications Commission Class A

Statement .............. 62

Russia Electromagnetic Interference Class A

Statement .............. 63

Homologation statement .......... 63

iv Installation and User Guide - Model 084

Figures

1. Chassis label (FCC compliance) ...... 2

2. Module bay caution label ........ 3

3. Compliance label with safety warning label 5

4. Drawer caution label .......... 5

5. Enclosure: front view.......... 9

6. Enclosure: rear view ......... 10

7. Module locations........... 11

8. Drawer LEDs (left side only)....... 12

9. A disk drive in carrier (DDIC) ...... 13

10. Enclosure operator’s panel ....... 14

11. 2800W PSU ............ 15

12. PSU LEDs ............. 16

13. Cooling module ........... 17

14. 6Gb/s SAS EBOD module ....... 18

15. Unpacking the system ......... 20

16. Mounting the system into a rack (left rail only) 21

17. Rear enclosure mounting ........ 22

18. PSU Power Switch and LEDs ...... 25

19. Ops panel LEDs ........... 26

20. Anti-tamper locks .......... 28

21. PSU LEDs ............. 30

22. Cooling module LEDs ......... 31

23. Operator’s panel LEDs......... 32

24. Drawer LEDs (left sideplane only) ..... 33

25. Drive Fault LED ........... 34

26. SBB I/O module LEDs ......... 34

27. Anti-tamper locks (shown disengaged) 38

28. Opening the bottom drawer ....... 38

29. Drawer latch ............ 39

30. Drive location plan .......... 40

31. Removing a DDIC .......... 41

32. Installing a DDIC .......... 41

33. Latch position of a correctly inserted drive 42

34. Cooling module LEDs ......... 43

35. Removing a Cooling Module (1) ..... 43

36. Removing a Cooling Module (2) ..... 44

37. Removing a PSU module (1) ....... 45

38. Removing a PSU Module (2) ....... 45

39. SBB I/O module LEDs ......... 46

40. Removing a module (1). (6Gb/s SAS EBOD

module shown) ........... 47

41. Removing an I/O module (2) ...... 47

vi Installation and User Guide - Model 084

Tables

1. Ops panel LEDs ........... 26

2. PSU LED states ........... 30

3. Cooling module LED descriptions ..... 31

4. Ops panel LED descriptions ....... 32

5. Drawer LED descriptions ........ 33

6. 6Gb/s SAS EBOD I/O Module LED

Descriptions ............ 34

7. Alarm Conditions .......... 35

8. Enclosure dimensions ......... 49

9. Component weights.......... 49

10. Components ............ 49

11. Thermal specifications ......... 50

12. Temperature and humidity limits ..... 50

13. PSU specifications .......... 50

14. Supported drives for enclosure ...... 51

15. Shock and vibration tolerance ...... 51

16. Power cord specifications ........ 56

viii Installation and User Guide - Model 084

Safety and environmental notices

Review the safety notices, environmental notices, and electronic emission notices for IBM ESS expansion

(5147-106) before you install and use the product.

Suitability for telecommunication environment: This product is not intended to connect directly or

indirectly by any means whatsoever to interfaces of public telecommunications networks.

Here are examples of a caution and a danger notice. Numbers in parentheses refer to message numbers

in the IBM Safety Notices publication G229-9054, which is included with your product.

CAUTION:

A caution notice indicates the presence of a hazard that has the potential of causing moderate or

minor personal injury. (C001)

DANGER

A danger notice indicates the presence of a hazard that has the potential of causing death or serious

personal injury. (D002)

Safety notices

Required safety notices for this product.

Familiarize yourself with the IBM Safety Notices publication G229-9054, which is included with your

product.

DANGER

When working on or around the system, observe the following precautions:

Electrical voltage and current from power, telephone, and communication cables are hazardous. To

avoid a shock hazard:

vIf IBM®supplied the power cord(s), connect power to this unit only with the IBM provided

power cord. Do not use the IBM provided power cord for any other product.

vDo not open or service any power supply assembly.

vDo not connect or disconnect any cables or perform installation, maintenance, or reconfiguration

of this product during an electrical storm.

vThe product might be equipped with multiple power cords. To remove all hazardous voltages,

disconnect all power cords.

vConnect all power cords to a properly wired and grounded electrical outlet. Ensure that the outlet

supplies proper voltage and phase rotation according to the system rating plate.

vConnect any equipment that will be attached to this product to properly wired outlets.

vWhen possible, use one hand only to connect or disconnect signal cables.

vNever turn on any equipment when there is evidence of fire, water, or structural damage.

vDo not attempt to switch on power to the machine until all possible unsafe conditions are

corrected.

vAssume that an electrical safety hazard is present. Perform all continuity, grounding, and power

checks specified during the subsystem installation procedures to ensure that the machine meets

safety requirements.

vDo not continue with the inspection if any unsafe conditions are present.

vDisconnect the attached power cords, telecommunications system, networks, and modems before

you open the device covers, unless instructed otherwise in the installation and configuration

procedures.

vConnect and disconnect cables as described in the following procedures when installing, moving,

or opening covers on this product or attached devices.

To disconnect:

1. Turn off everything (unless instructed otherwise).

2. Remove the power cords from the outlets.

3. Remove the signal cables from the connectors.

4. Remove all cables from the devices.

To connect:

1. Turn off everything (unless instructed otherwise).

2. Attach all cables to the devices.

3. Attach the signal cables to the connectors.

4. Attach the power cords to the outlets.

5. Turn on the devices.

vSharp edges, corners and joints may be present in and around the system. Use care when

handling equipment to avoid cuts, scrapes and pinching. (D005)

xInstallation and User Guide - Model 084

Inhaltsverzeichnis

Andere IBM Netzwerkspeicherserver Handbücher

IBM

IBM J15 Bedienungsanleitung

IBM

IBM SAN512B-6 Handbuch

IBM

IBM x Series 200 Betriebsanleitung

IBM

IBM 2073-700 Bedienungsanleitung

IBM

IBM TotalStorage DS4500 Bedienungsanleitung

IBM

IBM N3700 A20 Handbuch

IBM

IBM TotalStorage DS4400 Bedienungsanleitung

IBM

IBM TotalStorage FAStT600 Bedienungsanleitung

IBM

IBM DS3500 Bedienungsanleitung

IBM

IBM TotalStorage NAS Gateway 300 Programmierhandbuch

IBM

IBM TotalStorage DS4100 Betriebsanleitung

IBM

IBM SAN256B-6 Handbuch

IBM

IBM Storwize V7000 Bedienungsanleitung

IBM

IBM TotalStorage FAStT700 Bedienungsanleitung

IBM

IBM SAN06B-R Handbuch

IBM

IBM 9370 Bedienungsanleitung

IBM

IBM TotalStorageFAStT900 Bedienungsanleitung

IBM

IBM TotalStorage FAStT600 Bedienungsanleitung

IBM

IBM TotalStorage DS4300 Turbo Bedienungsanleitung

IBM

IBM totalstorage 200 Handbuch

IBM

IBM 7979A1U Bedienungsanleitung

IBM

IBM TotalStorage DS4300 Turbo Betriebsanleitung

IBM

IBM 220 Betriebsanleitung

IBM

IBM TOTALSTORAGE NAS 200 Bedienungsanleitung

Beliebte Netzwerkspeicherserver Handbücher anderer Marken

HP NetStorage 6000 Bedienungsanleitung

Seagate

Seagate U10 ST320423A Bedienungsanleitung

Synology

Synology RackStation RS816 Handbuch

D-Link

D-Link ShareCenter Pro DNS-1200-05 Bedienungsanleitung

Avid Technology

Avid Technology VideoRAID ST Sicherheitsleitfaden

Western Digital

Western Digital My Cloud Home Duo Bedienungsanleitung

PrimeArray

PrimeArray 4xxx Bedienungsanleitung

Buffalo

Buffalo TeraStation WSS WSH5010N6 Bedienungsanleitung

Planex

Planex MZK-NAS01SG Bedienungsanleitung

Intel

Intel SS4000-E - Entry Storage System NAS Server Bedienungsanleitung

Synology

Synology RS2212+ Bedienungsanleitung

Allnet

Allnet ALL69000 Bedienungsanleitung

Adaptec

Adaptec 5325301580 Bedienungsanleitung

Motorola

Motorola EXORdisk II Bedienungsanleitung

Sony

Sony XDAAI1PK Bedienungsanleitung

Cisco

Cisco Linksys NAS200 Original Betriebsanleitung

Sans Digital

Sans Digital MR4UT6G Bedienungsanleitung

AIC

AIC FB128-LX Bedienungsanleitung