Icom IC-F1721 Bedienungsanleitung

INSTRUCTION MANUAL

Icom Inc

This model is IC-F1821/D

or IC-F2821/D

This device complies with Part 15 of the FCC Rules.

Operation is subject to the condition that this device

does not cause harmful interference.

UHF MOBILE TRANSCEIVER

iF2821/D

iF2721/D

VHF MOBILE TRANSCEIVER

iF1821/D

iF1721/D

!IC-F1721D.qxd 04.9.15 9:43 AM Page a (1,1)

EXPLICIT DEFINITIONS

RWARNING! NEVER connect the transceiver to an

AC outlet. This may pose a ﬁre hazard or result in an electric

shock.

NEVER connect the transceiver to a power source of more

than 16 V DC such as a 24 V battery. This connection will ruin

the transceiver.

NEVER cut the DC power cable between the DC plug and

fuse holder. If an incorrect connection is made after cutting,

the transceiver might be damaged.

NEVER place the transceiver where normal operation of

the vehicle may be hindered or where it could cause bodily

injury.

NEVER allow children to touch the transceiver.

NEVER expose the transceiver to rain, snow or any liquids.

USE the specified microphone only. Other microphones

have different pin assignments and may damage the trans-

ceiver.

DO NOT use or place the transceiver in areas with tem-

peratures below –30°C (–22°F) or above +60°C (+140°F), or

in areas subject to direct sunlight, such as the dashboard.

PRECAUTION

WORD DEFINITION

RWARNING Personal injury, ﬁre hazard or electric shock

may occur.

CAUTION Equipment damage may occur.

NOTE If disregarded, inconvenience only. No risk

of personal injury, ﬁre or electric shock.

READ ALL INSTRUCTIONS carefully and com-

pletely before using the transceiver.

SAVE THIS INSTRUCTION MANUAL— This

instruction manual contains important operating instructions

for the IC-F1721/D, F1821/D, F2721/D and F2821/D VHF/

UHF MOBILE TRANSCEIVERS.

IMPORTANT

Icom, Icom Inc. and the logo are registered trademarks of Icom

Incorporated (Japan) in the United states, the United Kingdom, Germany,

France, Spain, Russia and/or other countries.

All other products or brands are registered trademarks or trademarks of their

respective holders.

!IC-F1721D.qxd 04.9.15 9:43 AM Page i (1,1)

AVOID operating the transceiver without running the vehi-

cle’s engine. The vehicle’s battery will quickly run out if the

transceiver transmits while the vehicle’s engine OFF.

AVOID placing the transceiver in excessively dusty envi-

ronments.

AVOID placing the transceiver against walls. This will

obstruct heat dissipation.

AVOID the use of chemical agents such as benzine or

alcohol when cleaning, as they damage the transceiver sur-

faces.

BE CAREFUL! The transceiver will become hot when

operating continuously for long periods.

For U.S.A. only

CAUTION: Changes or modifications to this transceiver, not ex-

pressly approved by Icom Inc., could void your authority to operate

this transceiver under FCC regulations.

ABOUT APCO PROJECT 25

This device made under license under one or more of the fol-

lowing US patents: #4,590,473, #4,636,791, #5,148,482,

#5,185,796, #5,271,017, #5,377,229.

The IMBE™ voice coding Technology embodied in this prod-

uct is protected by intellectual property rights including patent

rights, copyrights and trade secrets of Digital Voice Systems,

Inc. This voice coding Technology is licensed solely for use

within this Communications Equipment. The user of this

Technology is explicitly prohibited from attempting to decom-

pile, reverse engineer, or disassemble the Object Code, or in

any other way convert the Object Code into a human-readable

form. U.S. Pat. Nos. #5,870,405, #5,826,222, #5,754,974,

#5,701,390, #5,715,365, #5,649,050, #5,630,011, #5,581,656,

#5,517,511, #5,491,772, #5,247,579, #5,226,084, #5,195,166.

!IC-F1721D.qxd 04.9.15 9:43 AM Page ii (1,1)

iii

TABLE OF CONTENTS

IMPORTANT ....................................................................................... i

EXPLICIT DEFINITIONS .................................................................... i

PRECAUTION .................................................................................... i

ABOUT APCO PROJECT 25 ............................................................. ii

TABLE OF CONTENTS .................................................................... iii

1 PANEL DESCRIPTION .............................................................. 1–7

■Front panel .................................................................................. 1

■Function display .......................................................................... 2

■Programmable function keys ...................................................... 3

2 BASIC OPERATION ................................................................ 8–13

■Turning power ON ....................................................................... 8

■Channel selection ....................................................................... 8

■Call procedure ............................................................................ 9

■Receiving and transmitting ......................................................... 9

DTransmitting notes .................................................................. 10

DTX code channel selection ..................................................... 10

DTX code number edit .............................................................. 11

DIndividual ID code selection.................................................... 12

DTalkgroup ID code selection ................................................... 12

DDTMF transmission ................................................................ 12

■User set mode .......................................................................... 13

■Scrambler function .................................................................... 13

3 BIIS OPERATION ................................................................... 14–24

■Default setting ........................................................................... 14

■Receiving a call ......................................................................... 14

DIndividual call.......................................................................... 14

DGroup call ............................................................................... 15

DDisplaying the received call record......................................... 15

■Transmitting a call ..................................................................... 16

DUsing call memory.................................................................. 16

DCalling back from the queue channel ..................................... 16

DDirect code entry .................................................................... 17

■Receiving a message ............................................................... 18

DReceiving a status message .................................................. 18

DReceiving an SDM (Short Data Message) ............................. 18

DReceived message selection.................................................. 19

■Transmitting a status ................................................................. 20

DGeneral................................................................................... 20

DTransmitting a status .............................................................. 20

■Transmitting an SDM (Short Data Message) ............................. 21

DGeneral................................................................................... 21

DTransmitting an SDM.............................................................. 21

DProgramming an SDM memory.............................................. 22

■Position data transmission ........................................................ 23

■Printer connection ..................................................................... 23

■Digital ANI ................................................................................. 23

■Auto emergency transmission ................................................... 23

■Stun function ............................................................................. 24

■BIIS indication ........................................................................... 24

■Priority A channel selection ....................................................... 24

■Horn output ............................................................................... 24

4 CONNECTION AND MAINTENANCE ................................... 25–29

■Rear panel connection .............................................................. 25

■Supplied Accessories ................................................................ 26

■Mounting the transceiver ........................................................... 27

■Optional UT-111 installation ...................................................... 27

■Optional UT-109 or UT-110 installation ..................................... 28

■Optional OPC-617 installation ................................................... 28

■Antenna...................................................................................... 29

■Fuse replacement ..................................................................... 29

■Cleaning .................................................................................... 29

■Options ..................................................................................... 29

5 SAFETY TRAINING INFORMATION ........................................... 30

!IC-F1721D.qxd 04.9.15 9:43 AM Page iii (1,1)

PANEL DESCRIPTION

Icom Inc

yoruti

qe*w

IC-F1721/D

IC-F1821/D

F2721/D

F2821/D

■Front panel

qAF VOLUME CONTROL KNOB

Rotate the knob to adjust the audio output level.

•Minimum audio level is pre-programmed.

wFUNCTION DISPLAY (p. 2)

Displays a variety of information, such as an operating

channel number/name, 5-tone code, DTMF numbers and

audible condition, etc.

eDIAL or UP/DOWN KEYS

•IC-F1721/D, F2721/D: DIAL

Rotate to select an operating channel, etc.

•IC-F1821/D, F2821/D: UP/DOWN Keys

Push to select an operating channel, etc.

*The desired function can be assigned by your dealer. (p. 3)

r10-KEYPAD (IC-F1821/D or IC-F2821/D only)

The keypad allows you to enter digits to:

•Select memory channels, tone channels and DTMF codes

(when in the DTMF code channel selection mode)

•Set TX codes and BIIS status number

•Input text message for SDM operation

•Start up with a password

•Input the Individual ID code for digital operation.

tBUSY INDICATOR

Lights green while receiving a signal, or when the squelch

is open.

!IC-F1721D.qxd 04.9.15 9:43 AM Page 1 (1,1)

1PANEL DESCRIPTION

yPOWER SWITCH [POWER]

Push to turn the power ON and OFF.

•The following functions are available at power ON as options:

- Automatic scan start

- Password prompt

- Set mode

uTRANSMIT INDICATOR

Lights red while transmitting.

iDEALER-PROGRAMMABLE KEYS

Desired functions can be programmed independently by

your dealer. (p. 3)

In this instruction manual, these keys are from the left,

called [P0]/[P1]/[P2]/[P3]/[P4].

oMICROPHONE CONNECTOR

Connect the supplied microphone or optional DTMF micro-

phone.

NEVER connect non-specified microphones. The pin

assignments may be different and the transceiver may

be damaged.

DDMICROPHONE

The supplied microphone has a PTT switch and a hanger

hook.

•The following functions are available when the microphone is on or

off hook:

- Automatic scan start when on hook.

- Automatic priority channel selection when off hook.

- Sets to ‘Inaudible’condition (mute condition) when on hook.

- Sets to ‘Audible’condition (unmute condition) when off hook.

■Function display

qSIGNAL STRENGTH INDICATOR

Indicates relative signal strength level.

wLOW POWER INDICATOR

Appears when low output power is selected.

eAUDIBLE INDICATOR

➥Appears when the channel is in the ‘audible’(unmute)

condition.

➥Appears when the specified 2/5-tone/BIIS code is

received.

rCOMPANDER INDICATOR

Appears when the compander function is activated.

tSCRAMBLER INDICATOR

Appears when the voice scrambler function is activated.

136.1 Nar

q w e r t y uio

!IC-F1721D.qxd 04.9.15 9:43 AM Page 2 (1,1)

PANEL DESCRIPTION

yBELL INDICATOR

Appears/blinks when the specific 2/5-tone/BIIS code is

received, according to the pre-programming.

uCALL CODE MEMORY INDICATOR

Appears when the call code memory is selected.

iSCROLL INDICATOR

Appears when a received SDM including more than 12

characters is displayed.

oSDM INDICATOR

Appears when an SDM is received, or a transmit SDM is

selected.

!0 ALPHANUMERIC DISPLAY

Displays an operating channel number, channel name, Set

mode contents, DTMF code, etc.

The indication mode can be selected from 1 line or 2 lines.

Ask your dealer for details.

In this instruction manual, the LCD illustration is described

using the 2 lines indication mode.

!1 ACTIVATED KEY INDICATOR

Appears above the key assigned as [DIGITAL] key when

that key has been activated.

■Programmable function keys

The following functions can be assigned to [DIAL]*, [UP],

[DOWN], [P0], [P1], [P2], [P3] and [P4] programmable func-

tion keys.

Consult your Icom dealer or system operator for details con-

cerning your transceivers programming.

If the programmable function names are bracketed in the fol-

lowing explanations, the speciﬁc key is used to activate the

function depends on the programming.

*The functions you can assign to [DIAL] are limited.

(Only functions marked with ✩can be assigned.)

✩CH UP AND DOWN KEYS

➥Push (or Rotate)* to select an operating channel.

➥Push (or Rotate)* to select a transmit code channel after

pushing [TX Code CH Select].

➥Push (or Rotate)* to select a DTMF channel after pushing

[DTMF Autodial].

➥Push (or Rotate)* to select a scan group after pushing and

holding [Scan A Start/Stop]/[Scan B Start/Stop].

➥Push (or Rotate)* to select a BIIS code, status number or

SDM after pushing [Digital].

➥Push (or Rotate)* to select an Individual ID code or

Talkgroup ID code after pushing [Individual] or [Talkgroup].

*Rotate when this function is assigned to [DIAL].

✩ZONE UP AND DOWN KEY (This function is for [DIAL] only)

Rotate to select the desired zone.

!IC-F1721D.qxd 04.9.15 9:43 AM Page 3 (1,1)

1PANEL DESCRIPTION

ZONE SELECT KEY

Push this key, then select the desired zone using [CH Up]/

[CH Down].

What is “zone”?—The desired channels are assigned

into a zone according to the intended use. For example,

‘Staff A’and ‘Staff B’are assigned into a “Business”zone,

and ‘John’and ‘Cindy’are assigned into a “Private”zone.

SCAN A KEY

➥This key’s operation depends on the Power ON Scan setting.

When the power ON scan function is turned OFF;

Push to start and cancel scanning operation. In case of

transmission during scan, cancels scanning.

When the power ON scan function is turned ON;

Push to pause scanning. Scanning resumes after a speci-

ﬁed time period has passed. In case of transmission during

scan, pauses scanning. Scanning resumes after a speciﬁed

time period has passed after the transmission is ﬁnished.

➥Push and hold this key for 1 sec. to indicate the scan group,

then select the desired group using [CH Up]/[CH Down].

SCAN B KEY

➥Push to start and cancel scanning operation. In case of

transmission during scan, pauses scanning. Scanning

resumes after a speciﬁed time period has passed after the

transmission is ﬁnished.

➥Push and hold this key for 1 sec. to indicate the scan

group, then select the desired group using [CH Up]/

[CH Down].

SCAN TAG KEY

Push to add or delete the selected channel to/from the scan

group.

PRIORITY CHANNEL KEYS

➥Push to select Priority A or Priority B channel.

➥Push and hold [Prio A (Rewrite)] to rewrite the Prio A chan-

nel.

MR-CH 1/2/3/4 KEYS

Push to select an operating channel directly.

MONITOR KEY

➥Mute and release the CTCSS (DTCS) or 2-tone squelch

mute. Open any squelch/deactivate any mute while push-

ing this key. (LMR operation only)

➥Activates one of (or two of) the following functions on each

channel independently: (PMR or BIIS PMR operation only)

•Push and hold to un-mute the channel (audio is emitted; ‘Audible’

condition).

•Push to mute the channel (sets to ‘Inaudible’only).

•Push to un-mute the channel (sets to ‘Audible’only).

•Push after the communication is ﬁnished to send a ‘reset code’.

NOTE: The un-mute condition (‘Audible’condition) may

automatically return to the mute condition (‘Inaudible‘con-

dition) after a speciﬁed period depending on programming.

!IC-F1721D.qxd 04.9.15 9:43 AM Page 4 (1,1)

PANEL DESCRIPTION

PUBLIC ADDRESS KEY

While in the hailer mode, push this key for the audio output

via the hailer ampliﬁer. Ask your dealer for details.

While in the normal mode, the audio output via the cable can

be controlled from the transceiver separately from [VOL] con-

trol knob when an optional OPC-617

ACC CABLE

is installed.

•This audio output can be used as a ‘public address’function when

an external audio ampliﬁer and speaker are connected additionally.

•Push this key, then speak into the microphone while pushing the

PTT switch.

•[CH Up]/[CH Down] allow you to set the audio output level from min-

imum to maximum.

RX SPEAKER KEY

While in the hailer mode, the external speaker drive function

is also available simultaneously when the external connec-

tions are made for the ‘public address’function. The received

audio can be heard via the external speaker when this key is

pushed.

•This function is useful when you are out of the vehicle.

•The audio output level is linked to the transceiver’s volume control.

LIGHT KEY

Push to turn the transceiver’s backlight ON temporarily when

the backlight function is turned OFF in user set mode.

LOCK KEY

Push and hold to electronically lock all programmable keys

except the following:

[Call] (incl. Call A and Call B), [Moni(Audi)] and [Emergency].

OUTPUT POWER SELECTION KEY

Push to select the transmit output power temporarily or per-

manently, depending on the pre-setting.

•Ask your dealer for the output power level for each selection.

C.TONE CHANNEL ENTER KEY

Push to select the continuous tone channel using [CH Up]/

[CH Down] to change the tone frequency/code setting after

pushing this key. The selected channel remains set as the

continuous tone channel until another channel is designated

as such.

TALK AROUND KEY

Turn the talk around function ON and OFF.

•The talk around function equalizes the transmit frequency to the

receive frequency for transceiver-to-transceiver communication.

WIDE/NARROW KEY

Push to toggle the IF bandwidth between wide and narrow.

•The wide passband width can be selected from 25.0 or 20.0 kHz

using the CS-F1700

CLONING SOFTWARE

. (PMR or BIIS PMR opera-

tion only) Ask your Dealer for details.

DTMF AUTODIAL KEY

➥Push to enter the DTMF channel selection mode. Then

select the desired DTMF channel using [CH Up]/[CH Down].

➥After selecting the desired DTMF channel, push this key to

transmit the DTMF code.

!IC-F1721D.qxd 04.9.15 9:43 AM Page 5 (1,1)

1PANEL DESCRIPTION

DTMF RE-DIAL KEY

Push to transmit the last-transmitted DTMF code.

CALL KEYS

Push to transmit a 2/5-tone/BIIS ID code.

•Call transmission is necessary before calling another station

depending on your signalling system.

•[Call A] and/or [Call B] may be available when your system employs

selective ‘Individual/Group’calls. Ask your dealer which call is

assigned to each key.

EMERGENCY KEYS

➥Push and hold to transmit an emergency call.

➥When [Emergency Single (Silent)] or [Emergency Repeat

(Silent)] is pushed, an emergency call is transmitted without

a beep emission and LCD indication change.

•If you want to cancel the emergency call, push (or push and

hold) the key again before transmitting the call.

•The emergency call is transmitted one time only or repeatedly

until receiving a control code depending on the pre-setting.

TX CODE ENTER KEY (PMR or BIIS PMR operation only)

Push to enter the ID code edit mode directly, for both 5-tone

and MSK. Then set the desired digit using [CH Up]/

[CH Down] or 10-keypad*. (p. 11)

*IC-F1821/D or IC-F2821/D only

TX CODE CHANNEL SELECT KEY

➥Push to enter the ID code channel selection mode directly.

Then set the desired channel using [CH Up]/[CH Down].

(p. 10)

➥During ID code channel selection mode, push for 1 sec. to

enter the ID code edit mode for 5-tone and MSK. Then set

the desired digit using [CH Up]/[CH Down] or 10-keypad*.

(p. 11)

*IC-F1821/D or IC-F2821/D only

✩TX CODE CHANNEL UP/DOWN KEYS

Push (or Rotate)* to select a TX code channel directly.

*Rotate when this function is assigned to [DIAL].

ID MEMORY READ KEY (PMR or BIIS PMR operation only)

➥Recalls detected ID codes.

•Push this key, then select the ID code using [CH Up]/[CH Down].

•Up to 5 ID’s are memorized.

➥Push and hold to erase the selected ID’s.

VOICE SCRAMBLER FUNCTION

Push to toggle the voice scrambler function ON and OFF.

COMPANDER KEY

Push to toggle the compander function ON and OFF.

The compander function reduces noise components from the

transmitted audio to provide clear communication.

!IC-F1721D.qxd 04.9.15 9:43 AM Page 6 (1,1)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Icom Transceiver Handbücher

Icom

Icom IC-M4A Bedienungsanleitung

Icom

Icom IC-F3162T Bedienungsanleitung

Icom

Icom IC-F9011B Bedienungsanleitung

Icom

Icom iF3200DEX series Bedienungsanleitung

Icom

Icom IC-7000 Bedienungsanleitung

Icom

Icom IC-A14 Bedienungsanleitung

Icom

Icom IC-W2A Bedienungsanleitung

Icom

Icom IC-M423GE Bedienungsanleitung

Icom

Icom IC-F15 Bedienungsanleitung

Icom

Icom IC-7300 Bedienungsanleitung

Icom

Icom IC-F620 Bedienungsanleitung

Icom

Icom IC-707 Bedienungsanleitung

Icom

Icom IC-M710 Bedienungsanleitung

Icom

Icom IC-iV85 Bedienungsanleitung

Icom

Icom IC-905 Einrichtungshandbuch

Icom

Icom IC-7000 Bedienungsanleitung

Icom

Icom IC-9100 Bedienungsanleitung

Icom

Icom IC-M32 Bedienungsanleitung

Icom

Icom IC-725 Bedienungsanleitung

Icom

Icom IC-V8000 Bedienungsanleitung

Icom

Icom IC-E7 Bedienungsanleitung

Icom

Icom IC-9100 Bedienungsanleitung

Icom

Icom IC-M505 Bedienungsanleitung

Icom

Icom IC-706MKII Bedienungsanleitung

Beliebte Transceiver Handbücher anderer Marken

Yaesu

Yaesu FT-7B Bedienungsanleitung

Kenwood

Kenwood ProTalk TK-3201 Bedienungsanleitung

Mizuho

Mizuho MX-2 Produkthandbuch

Kenwood

Kenwood TK-3180 Bedienungs- und Wartungshandbuch

Blitz

Blitz MJ-398U Bedienungsanleitung

Utilicom

Utilicom LongRanger 2050 Bedienungsanleitung

Standart

Standart HX290UKA Bedienungsanleitung

Altronix

Altronix Pace1PTM Bedienungsanleitung

Kirisun

Kirisun PT2208 Bedienungsanleitung

ELECRAFT

ELECRAFT KX2 Bedienungsanleitung

Zodiac

Zodiac K3 Bedienungsanleitung

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Bedienungsanleitung

Kenwood

Kenwood TK-2217 Bedienungsanleitung

Siemens

Siemens PSO 4000 Bedienungsanleitung

Kenwood

Kenwood TS-590SG Bedienungsanleitung

Midland

Midland G8E-BT Handbuch

ComNav

ComNav Mariner X2 Bedienungsanleitung

Uniden

Uniden UH820 Series Bedienungsanleitung