ICP DAS USA M-7002 Bedienungsanleitung

M-7002 - 4-ch AI, 5-ch DI and 4-ch Relay Output DAQ Module - QuickStart (Jun/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

M-7002

4-channel AI, 5-channel DI and 4-channels

Relay OutputData Acquisition Module

Quick Start Guide

Product Website:

https://www.icpdas-usa.com/m_7002.html

http://www.icpdas-usa.com/dcon_utility_pro.html

1. Introduction

The M-7002 is a 16-bit, 4-channel differential analog inputs 5-channel digital inputs and

4-channels for relay output. All of its channels are Form A type relay module that

provides programmable input range on all analog channels (+/-150 mV, +/-500 mV, +/-1

V, +/-5 V, +/-10 V, +/-20 mA, 0 ~ 20 mA and 4 ~ 20 mA) and digital output can be set

alarm output with shortcircuit protection and overload protection. Each analog channel

is allowed to configure an individual range and has 240 Vrms high overvoltage

protection. Jumper selectable for voltage or current input. The sampling rate of M-7002

is changeable; there are fast mode and normal mode for your consideration. M-7002

also has qualification for 4 kV ESD protection as well as 2500 VDC intra-module

isolation.

2. Terminal Assignment

M-7002 - 4-ch AI, 5-ch DI and 4-ch Relay Output DAQ Module - QuickStart (Jun/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

3. Block/ Wiring Diagram

4. Default Settings

Default settings for the M-7005 modules are as follows:

▫Protocol: Modbus RTU

▫Module Address: 01

▫Thermistor Type: Type 60, PreCon Type III, -30°F to 240°F

▫Baud Rate: 9600 bps

▫Temperature Scale: Celsius (the M-7005 also supports Fahrenheit for DCON protocol)

M-7002 - 4-ch AI, 5-ch DI and 4-ch Relay Output DAQ Module - QuickStart (Jun/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5. Configuration

To install the module, follow the steps below:

1. Connect the thermistor analog input.

2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals. If

the host is only equipped with an RS-232 interface, then an RS-232 to RS-485

converter will be required.

3. Connect the module to the power supply using the +Vs and GND terminals. Note that

the voltage supplied should be in the range of +10 to +30V DC.

M-7002 - 4-ch AI, 5-ch DI and 4-ch Relay Output DAQ Module - QuickStart (Jun/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4. Open DCON utility pro

click on COM port(first icon).

It can select multi-options such as Baud Rate, Protocol, Checksum, and Format to

search module. The default settings for the module can be found in Section 3. Click OK

after selecting the COM port setting.

M-7002 - 4-ch AI, 5-ch DI and 4-ch Relay Output DAQ Module - QuickStart (Jun/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5. DCON utility pro will search for the selected COM port according the setting

previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS

and the others modules.

6. Configuration I/O module setting on PC

M-7002 - 4-ch AI, 5-ch DI and 4-ch Relay Output DAQ Module - QuickStart (Jun/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

7. For M-7000 modules, DCON utility pro terminal can send command to the module.

See user manual Sections 2 for details command.

Configure the module: sending the %AANNTTCCFF command. See Section 2.1 for

details. To configure the M-7005, the $AA7CiRrr command must also be sent. See user

manual Section 2.12 for details. For M-7000 modules using the Modbus RTU protocol,

configure the module using the following functions.

-Sub-function 04h of Function 46h, see user manual Section 3.6.2

-Sub-function 06h of Function 46h, see user manual Section 3.6.4

-Sub-function 08h of Function 46h, see user manual Section 3.6.6

Read data from the input channels: send either the #AA or #AAN commands to the

module. See user manual Sections 2.3 and 2.4 for details. For M-7000 modules using

the Modbus RTU protocol, use Function 04h to read the data from the input channels.

See user manual Section 3.3 for details.

M-7002 - 4-ch AI, 5-ch DI and 4-ch Relay Output DAQ Module - QuickStart (Jun/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

8. If user doesn’t know command, user can select Address and ID, it will show some

refer commands as below. User can select necessary command to test or debug

modules.

Inhaltsverzeichnis

Andere ICP DAS USA Steuereinheit Handbücher

ICP DAS USA

ICP DAS USA ECAT-2016N Bedienungsanleitung

ICP DAS USA

ICP DAS USA USB-87P1 Bedienungsanleitung

ICP DAS USA

ICP DAS USA MDC-714i Bedienungsanleitung

ICP DAS USA

ICP DAS USA M-7033 Bedienungsanleitung

ICP DAS USA

ICP DAS USA I-7188XA Bedienungsanleitung

ICP DAS USA

ICP DAS USA tSG-3781B Bedienungsanleitung

ICP DAS USA

ICP DAS USA M-7064 Bedienungsanleitung

ICP DAS USA

ICP DAS USA GW-7552-M Bedienungsanleitung

ICP DAS USA

ICP DAS USA PM-3133i Bedienungsanleitung

ICP DAS USA

ICP DAS USA tSH-734 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tDS-700-T Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA CAN-8123 Bedienungsanleitung

ICP DAS USA

ICP DAS USA M-7024 Bedienungsanleitung

ICP DAS USA

ICP DAS USA M-7028 Bedienungsanleitung

ICP DAS USA

ICP DAS USA LP-8 21 Series Allgemeine Anweisungen

ICP DAS USA

ICP DAS USA I-8092F Stücklistenhandbuch

ICP DAS USA

ICP DAS USA I-7063D Bedienungsanleitung

ICP DAS USA

ICP DAS USA WISE-5801-MTCP Bedienungsanleitung

ICP DAS USA

ICP DAS USA iWSN-110X Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA SG-3016 Bedienungsanleitung

ICP DAS USA

ICP DAS USA M-7019Z Bedienungsanleitung

ICP DAS USA

ICP DAS USA ZT-257 Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA ET-87P2 Bedienungsanleitung

ICP DAS USA

ICP DAS USA ET-2200 Series Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung