ICP DAS USA M-7060 Bedienungsanleitung



M‐70604‐channelDIand4‐channelRelayOutputDAQModule

‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

1



M-7060

4-channel Digital Input and 4-channel Relay

Output Data Acquisition Module

Quick Start Guide

Product Website:

https://www.icpdas-usa.com/m_7060_m_7060d

http://www.icpdas-usa.com/dcon_utility_pro.html

1. Introduction

The 7060 series provides 4 digital input channels, 2 Form A and 2 Form C signal relay output

channels, while the M-7060P provides 4 digital input channels, 2 Form A and 2 Form C power

relay output channels. All digital input channels can be used as 16-bit counters. In addition, the

digital input channels can be selected either as sink- or source-type via wire connections. The

“D” versions of the 7060 series provide eight LED indicators that can be used to monitor the

status of the digital input and relay output. The “M” versions of the 7060 series support both the

Modbus RTU and DCON protocols, which can be configured via software. There are also

options for configuring power-on and safe values. 4 kV ESD protection and 3750 VDC intra-

module isolation are also provided to enhance noise protection capabilities in industrial

environments. The 7060 series is the ideal solution for small signal switching applications, while

the M-7060P is the perfect solution for high power applications.

2.TerminalAssignment



M‐70604‐channelDIand4‐channelRelayOutputDAQModule

‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

2



3.Block/WiringDiagram



M‐70604‐channelDIand4‐channelRelayOutputDAQModule

‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

3



4. Default Settings

。 Module Address: 01

。 DIO Type: Type 40

。 Baud Rate: 9600 bps

。 Checksum disabled

5. Configuration

To install the module, follow the steps below:

1. Connect the digital input and output.

2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals. If

the host is only equipped with an RS-232 interface, then an RS-232 to RS-485

converter will be required.

3. Connect the module to the power supply using the +Vs and GND terminals. Note that

the voltage supplied should be in the range of +10 to +30V DC.



M‐70604‐channelDIand4‐channelRelayOutputDAQModule

‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4



M‐70604‐channelDIand4‐channelRelayOutputDAQModule

‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5



4. Open DCON utility pro

click on COM port(first icon).

It can select multi-options such as Baud Rate, Protocol, Checksum, and Format

to search module. The default settings for the module can be found in Section 3.

Click OK after selecting the COM port setting.



M‐70604‐channelDIand4‐channelRelayOutputDAQModule

‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

6



5. DCON utility pro will search for the selected COM port according the setting

previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS

and the others modules.

6. Configuration I/O module setting on PC



M‐70604‐channelDIand4‐channelRelayOutputDAQModule

‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

7



7. For I-7000 modules, DCON utility pro terminal can send command to the module.

See user manual Sections 2 for details command.

Configure the module: sending the %AANNTTCCFF command. See user manual

Section 2 for details.

Read data from the input channels: send either the #AA or #AAN command to the

module.

8. If user doesn’t know command, user can select Address and ID, it will show some

refer commands as below. User can select necessary command to test or debug

modules.



Inhaltsverzeichnis

Andere ICP DAS USA Steuereinheit Handbücher

ICP DAS USA

ICP DAS USA I-87004W Bedienungsanleitung

ICP DAS USA

ICP DAS USA ZT-2510 Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA tSG-3781B Bedienungsanleitung

ICP DAS USA

ICP DAS USA CAN-8123 Bedienungsanleitung

ICP DAS USA

ICP DAS USA I-7188XA Bedienungsanleitung

ICP DAS USA

ICP DAS USA IR-310-RM Bedienungsanleitung

ICP DAS USA

ICP DAS USA I-7060D Bedienungsanleitung

ICP DAS USA

ICP DAS USA tZT-P4C4 Bedienungsanleitung

ICP DAS USA

ICP DAS USA LP-8 4 Series Allgemeine Anweisungen

ICP DAS USA

ICP DAS USA M-7019Z Bedienungsanleitung

ICP DAS USA

ICP DAS USA I-7080 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tPET-P6 Bedienungsanleitung

ICP DAS USA

ICP DAS USA M-7088 Bedienungsanleitung

ICP DAS USA

ICP DAS USA PROFIBUS PROFI-2510 Bedienungsanleitung

ICP DAS USA

ICP DAS USA M-7028 Bedienungsanleitung

ICP DAS USA

ICP DAS USA ET-2200 Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA ET-87P2 Bedienungsanleitung

ICP DAS USA

ICP DAS USA PM-3033 Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA EIP-2000 Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA ECAT-201x EtherCAT Slave I/O Bedienungsanleitung

ICP DAS USA

ICP DAS USA DS-2200 Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA SG-3784M Bedienungsanleitung

ICP DAS USA

ICP DAS USA SG-3016 Bedienungsanleitung

ICP DAS USA

ICP DAS USA ZT-2017 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung