IDTECH VP3300 OEM Bedienungsanleitung

VP3300 OEM User Manual

NFC Card reader

ID-80149014

80149510-004 Rev. A

ID TECH

10721 Walker Street

Cypress, CA 90630

USA

This document, as well as the software and hardware described in it, is furnished under

license and may be used or copied online in accordance with the terms of such license.

The content of this document is furnished for information use only, is subject to

change without notice, and should not be construed as a commitment by ID TECH.

While every effort has been made to ensure the accuracy of the information provided,

ID TECH assumes no responsibility or liability for any unintentional errors or

inaccuracies that may appear in this document. Except as permitted by such license, no

part of this publication may be reproduced or transmitted by electronic, mechanical,

recording, or otherwise, or translated into any language form without the express

written consent of ID TECH.

ID TECH and ViVOpay are trademarks or registered trademarks of ID TECH.

Warranty Disclaimer

The services and hardware are provided "as is" and "as-available" and the use of the

services and hardware are at its own risk. ID TECH does not make, and hereby disclaims,

any and all other express or implied warranties, including, but not limited to,

warranties of merchantability, fitness for a particular purpose, title, and any warranties

arising from a course of dealing, usage, or trade practice. ID TECH does not warrant

that the services or hardware will be uninterrupted, error-free, or completely secure.

Federal Communication Commission Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including

interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one of the

following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

- Changes or modifications to the VP3300 OEM not expressly approved by ID TECH

could void the user's authority to operate the device.

FCC Caution: Any changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority to operate this

equipment.

This transmitter must not be co-located or operating in conjunction with any

other antenna or transmitter.

Radiation Exposure Statement:

The product comply with the FCC portable RF exposure limit set forth for an

uncontrolled environment and are safe for intended operation as described in

this manual. The further RF exposure reduction can be achieved if the product

can be kept as far as possible from the user body or set the device to lower

output power if such function is available.

Industry Canada statement:

This device complies with ISED’s licence-exempt RSSs. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may

cause undesired operation.

Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio

exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) le

dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit

accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un

fonctionnement indésirable.

Radiation Exposure Statement:

The product comply with the Canada portable RF exposure limit set forth for an

uncontrolled environment and are safe for intended operation as described in this

manual. The further RF exposure reduction can be achieved if the product can be kept

as far as possible from the user body or set the device to lower output power if such

function is available.

Déclaration d'exposition aux radiations:

Le produit est conforme aux limites d'exposition pour les appareils portables RF pour

les Etats-Unis et le Canada établies pour un environnement non contrôlé.

Le produit est sûr pour un fonctionnement tel que décrit dans ce manuel. La réduction

aux expositions RF peut être augmentée si l'appareil peut être conservé aussi loin que

possible du corps de l'utilisateur ou que le dispositif est réglé sur la puissance de sortie

la plus faible si une telle fonction est disponible.

Introduction

VP3300 OEM is ID TECH's ultra-compact, EMV L1/L2-certified 2-way (contact EMV, and

contactless) card reader, based on the VP3300-series design, but with card-reader

componentry externalized to allow custom placement of card slots within a

customer-designed chassis.

The VP3300 OEM is built for low cost, high reliability, and maximum compatibility with

existing contactless payment technologies (including Apple Pay, Android Pay, and Samsung

Pay).

The VP3300 OEM incorporates the proven EMV L2 kernel of ID TECH's popular UniPay III

card reader. Developers can integrate VP3300 OEM into terminal systems with minimal

effort using ID TECH's Universal SDK, available for Windows, Android, or iOS.

Major Features of VP3300 OEM

•Micro-USB port for communications and power.

•ICC support: EMV Level 1 and EMV L2 approvals. All L1 & L2 on the device.

•Contactless transaction support via Near Field Communication (NFC).

•LED status indicator.

•Audio feedback.

•Field upgradable firmware.

•Standby mode for low power consumption.

•Compact and ergonomic design to integrate with a variety of devices.

•Available with a sturdy stand, for tabletop use.

•TDES and AES 128 encryption support.

•DUKPT key management.

•Software Development Kits for Windows, Android, iOS.

•One-year manufacturer's warranty.

ICC Contact Card Features

•EMVCo Contact Level 1 & 2 compliant

Contactless (NFC) Features

•Poll on Demand Mode:

oEMV CTLS L1

oVisa

oMastercard

oAMEX

oDiscover

oApple Pay

oApple VAS

oGoogle Pay

oGoogle Pay Smart Tap 2.1

oSamsung Pay

oInteract

•Pass-thru Mode:

oISO 14443 Type A&B

oISO 18092 (including P2P)

oMIFARE Classic 1K/4K

oMIFARE Ultra light &MIFARE Ultra light EV1

oMIFARE Ultra light C

oMIFARE DESFire

oMIFARE DESFire EV1 4K

oMIFARE Plus

oFeliCa™

•Smallest EMV certified Antenna

Before You Start Using VP3300 OEM

The VP3300 OEM is designed to operate in conjunction with certified third-party payment

software and compatible hosts, such as USB-equipped tablets, PCs, and smartphones.

Before you connect VP3300 to a host, install and activate the host software application

according to the instructions provided by your payment application service or software

provider, then connect the VP3300 OEM (or device containing the VP3300 OEM) to the host

through a micro-USB cable.

LED Status and Audible Beeper During Transactions and Operation

Device Status

4 LED’s

Audible Beeper

Run Mode

Left LED Flash 300ms on/5s off

Contactless Read Successful

All 4 LEDs flash Once

1 longer beep

Contactless Read Failed

2 short beeps

ICC is being Processed

Left LED flashes: 500ms on/off, DO

NOT remove card

How to use ID-80149014.

Select the interface you want to

use to connect PC and Reader.

USB

RS-232

Select the desired transaction

Users can find the corresponding

commands from DemoApp and

Consult the NEO Interface

Developers Guide (IDG).

Physical Specifications

Operation and Storage Environment

NFC Transceiver:

A dedicated transceiver chip is used to drive the NFC and contactless communication.

RF Frequency: 13.56MHz

Main feature of the NFC transceiver is listed below:

ISO18092(NFCIP-1) Active P2P

ISO14443 A, B

FeliCa™

Power Consumption

Item

Specification

Note

Power Input: Vin

DC +5V

Normal operating input range

Power Consumption

RUN <500mA (Max)

Contactless operating status

RUN < 90mA (Max)

Only ICC operating status

Other Agency Approvals and Compliances

•CE (EN55022/EN55024, Class- B)

•FCC (Part 15, Class-B)

•RoHS (DIRECTIVE 2011/65/EU)

•IC

•REACH

•EMV Contact L1&L2

•EMV Contactless L1

•TQM

For Software Developers: Software Development Support

VP3300 devices, including the VP3300 OEM, are designed to be compatible with a wide

range of third-party payment applications. ID TECH offers a Universal SDK (available for iOS,

Android, or Windows) to enable rapid application development with any model of VP3300

Item

Specification

Physical Dimensions

(Antenna Enclosure)

64mm x 64mm x 12mm (L x W x H)

(ICC module size is no included)

Structure Material

Plastic, PC Sabic 945

Texture

MT11010

Weight

66g (Including Cable)

Item

Specification

Note

Operating Temperature

-40 °C to 85 °C

Non-condensing

Storage Temperature

-40 °C to 85 °C

Non-condensing

Operating Humidity

Up to 95%

Non-condensing

Storage Humidity

Up to 95%

Non-condensing

as the target device. The languages supported include Objective C (on iOS), Java (on

Android), and C# (on Windows). The Universal SDK includes rich, powerful libraries that

make communication with VP3300 OEM comparatively easy while greatly facilitating

debugging.

Normally, development of applications that take advantage of VP3300 OEM capabilities can

be done in a high-level language like Java or C# (using convenience objects and data

structures), obviating the need to send hex-code commands directly via USB-HID.

Nevertheless, if you need to communicate with the device via RS-232 or via USB-HID, it is

possible to do so. For a command reference for VP3300-series products, consult the NEO

Interface Developers Guide (IDG), P/N 80139403-001.

Demo App

The Universal SDK comes with a rich, fully featured demo app. complete source code for the

demo app is included with the SDK.

To use the demo app: On Windows, plug your VP3300 OEM into the host using a

USB-to-micro-USB cable (not included), then double-click the UniversalSDKDemo.exe file

and allow a few seconds for the main window to appear (see illustration below).

The Demo App displays available commands in a command tree, as shown above.

Single-click on a command to populate the center panel of the window with optional

settings relevant to the command (e.g., "Amount" and "Start EMV Additional Tags" above).

In some cases, text fields will appear, allowing you to enter custom values. When you are

ready to execute the command in question, double-click it in the command tree. The

command executes in real time and a data trace appears automatically in the center and/or

right-hand panels. (Use the Clear Logs button to clear both panels.)

www.idtechproducts.com

support@idtechproducts.com

Revision History

Revision

Date

Description of Changes

05/04/2023

Initial release

Andere Handbücher für VP3300 OEM

Inhaltsverzeichnis

Andere IDTECH Kartenleser Handbücher

IDTECH

IDTECH SecureMag Bedienungsanleitung

IDTECH

IDTECH MINIMAG Bedienungsanleitung

IDTECH

IDTECH VP4880 Bedienungsanleitung

IDTECH

IDTECH PiP Bedienungsanleitung

IDTECH

IDTECH VP3300 OEM Bedienungsanleitung

IDTECH

IDTECH EasyMag Bedienungsanleitung

IDTECH

IDTECH MiniSmart II Bedienungsanleitung

IDTECH

IDTECH ViVOpay VP6300 Bedienungsanleitung

IDTECH

IDTECH ViVOpay VP5300 Bedienungsanleitung

IDTECH

IDTECH IDWA-332312 Gebrauchsanweisung

IDTECH

IDTECH ViVOpay KioskII Bedienungsanleitung

IDTECH

IDTECH ViVOpay VP3320 Bedienungsanleitung

IDTECH

IDTECH VP3300 Bedienungsanleitung

IDTECH

IDTECH BT Mag Bedienungsanleitung

IDTECH

IDTECH UniPay Gebrauchsanweisung

IDTECH

IDTECH minimag RS-232 Bedienungsanleitung

IDTECH

IDTECH ViVOpay VP5200 Bedienungsanleitung

IDTECH

IDTECH SmartPIN L80 Bedienungsanleitung

IDTECH

IDTECH SREDKey Gebrauchsanweisung

IDTECH

IDTECH NEO 3 VP3350 Bedienungsanleitung

IDTECH

IDTECH SecureMag Bedienungsanleitung

IDTECH

IDTECH MINIMAG Bedienungsanleitung

IDTECH

IDTECH Kiosk III Bedienungsanleitung

IDTECH

IDTECH 80140502-001 Bedienungsanleitung

Beliebte Kartenleser Handbücher anderer Marken

Lindy

Lindy 43185 Bedienungsanleitung

Lindy

Lindy 43185 Bedienungsanleitung

ViziT

ViziT RD-4F Bedienungsanleitung

Jinmuyu Electronics

Jinmuyu Electronics MR811 Series Bedienungsanleitung

AVID ID

AVID ID AVID1043 Bedienungsanleitung

Conrad

Conrad PCMCIA Bedienungsanleitung

Rosslare

Rosslare DR-6255 Bedienungsanleitung

Lindy

Lindy 51541 Bedienungsanleitung

Diapro T?bbi Ürünler

Diapro T?bbi Ürünler Across System Bedienungsanleitung

Johnson Controls

Johnson Controls Kantech tyco ioSmart Bedienungsanleitung

ACS

ACS ACR122L Bedienungsanleitung

Secukey

Secukey S2-MF Bedienungsanleitung

Elecom

Elecom MR-SMC07 series Bedienungsanleitung

Alien

Alien ALR-9800 Bedienungsanleitung

ACS

ACS ACR310 Bedienungsanleitung

Datamars

Datamars R-IN1300 MID Bedienungsanleitung

Alarm Lock

Alarm Lock AL-PRE2 Bedienungsanleitung

xpr

xpr B100PROX-AH Benutzerhandbuch