IDTECH VP8300 Bedienungsanleitung

VP8300 User Manual

ViVOpay VP8300 UserManual

80158500-001

ID TECH

10721 Walker Street

Cypress, CA 90630

USA

This document, as well as the hardware and software it describes, is furnished under

license and may only be used in accordance with the terms of such license. The content of

this paper is furnished for informational use, subject to change without notice, and not to be

construed as a commitment by ID TECH. ID TECH assumes no responsibility or liability for

any errors or inaccuracies that may appear in this document.

Except as permitted by such license, no part of this publication may be reproduced or

transmitted by electronic, mechanical, recorded, or any other method, or translated into

another language or language form without the express written consent of ID TECH. ID

TECH is a registered trademark of International Technologies and Systems Corporation.

ViVOpay and Value through Innovation are trademarks of International Technologies and

Systems Corporation. Other trademarks are the property of the respective owner.

Warranty Disclaimer: The services and hardware are provided "as is" and "as-available"

and the use of these services and hardware are at the user’s own risk. ID TECH does not

make, and hereby disclaims, any and all other express or implied warranties, including, but

not limited to warranties of merchantability, title, fitness for a particular purpose, and any

warranties arising from any course of dealing, usage, or trade practice. ID TECH does not

warrant that the services or hardware will be uninterrupted, error-free, or completely secure.

ViVOpay VP8300 UserManual

iii

FCC Regulatory Compliance

Notices Class B Equipment

This equipment has been tested and found to comply with the limits for a Class B digital device

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. This device complies with

part 15 of the FCC rules. Operation is subject to two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try and correct the

interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and the receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

•Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications to the ViVOpay VP8300 not expressly approved by ViVOtech could

void the user's authority to operate the ViVOpay VP8300.

RF exposure:

•To comply with the FCC RF exposure compliance requirements, this device and its antenna

must not be co-located or operating in conjunction with any other antenna or transmitter.

Cautions and Warnings

Caution: The ViVOpay VP8300 should be mounted 1-2 feet away from other

ViVOpay VP8300.

Warning: Avoid close proximity to radio transmitters which may reduce the ability of

the reader.

ViVOpay VP8300 UserManual

Table of Contents

1Overview ......................................................................................................1

1.1 Additional Features .........................................................................................1

1.2 ViVOpay VP8300 Specifications......................................................................2

1.3 Installing ViVOpay VP8300..............................................................................3

2Firmware Upgrade.......................................................................................5

2.1 Preparation......................................................................................................5

2.2 Procedure........................................................................................................5

3ViVOpay VP8300 Troubleshooting.............................................................7

4Glossary.......................................................................................................8

5Customer Support.....................................................................................10

1 Overview

The ViVOpay® VP8300 supports card swipe, contact and contactless payment

information processing and authorization at mobile devices.

The unit can accept a variety of contactless credit cards, contactless key

Fobs.

ViVOpay VP8300 supports the following contactless payment applications in the

latest release of firmware:

• PayPass ISO/IEC

• PayPass Magstripe

• PayPass MChip

• PayPass MXI

• RBS Application (M/Flex)

• VisaWave

• qVSDC/MSD

• American Express – ExpressPay

• Discover Zip

• ViVOwallet

• ViVONFC

• Mifare ePurse

This document assumes that users are familiar with their mobile systems and all

related functions.

Features

The ViVOpay VP8300 supports the following transaction types:

• Contactless RF devices such as ISO 14443 Type A and Type B, and

Mifare devices

1.1 Additional Features

• Contactless: Accepts transactions from consumers using ISO/IEC 14443 Type

A and B or NFC cards and key fobs.

• Speed: Enables quick transactions improving store productivity and operational

efficiencies.

• Implementations: POS peripheral.

• Consumer Intuitive: Equipped with LEDs and sound to provide visual and

audible cues to enable smooth and seamless transactions.

• Secure: Provides highly secure transactions whether financial, pre-paid, loyalty,

or gift.

ViVOpay VP8300 UserManual

1.2 ViVOpay VP8300 Specifications

Hardware

MTBF

200,000 hrs.

Transmitter

Frequency

13.56 MHz +/- 0.01%

Transmitter

Modulation

ISO 14443-2 Type A

Rise/Fall Time: 2-3 µsec. Rise, < 1 µsec fall

ISO 14443-2 Type B

Rise/Fall Time: < 2 µsec. each; 8% - 14% ASK

ISO 18092

Receiver Subcarrier

Frequency

847.5 KHz

Receiver Subcarrier

Data

ISO 14443-2 Type A: Modified Manchester

ISO 14443-2 Type B: NRZ-L, BPSK

ISO 18092

Typical Read Range

4-6 cm (1.5 to 2.3 inches)

Physical Dimensions

Height

45 mm (1.78 inches)

Width

141 mm (5.55 inches)

Depth

127 mm (5 inches)

Environmental

Operating

Temperature

0° C to 55° C (32° F to 131° F)

Storage Temperature

-20° C to 60° C (-4° F to 140° F)

Cold and Heat Shock

-20° C to 60° C (-4° F to 140° F) within 25 hrs.

Operating Humidity

5% to 95% non-condensing

Electrical

Reader Input Voltage

USB 5VDC; MAX 0.4A ; 2 Watts

ViVOpay VP8300 UserManual

1.3 Installing ViVOpay VP8300

This section describes how to install the ViVOpay VP8300 on a Desktop.

Launch the USDK and get into the main

screen, USDK will detect the VP8300

automatically(Share same tool with

VP3300).

When VP8300 is standby, the far left

LED will flash.

Contactless transaction:

Select “CTLS”->”Transaction”->”Start

CTLS Trans” to start a contactless

transaction.

When VP8300 is ready to tap card, the

first Green LED will be solid.

Tap the card on VP8300, if reading card

success, all four LEDs will blink once

with one long beep; if reading card

failure, only two short beeps be

sounded.

ViVOpay VP8300 UserManual

The SDK will go online and get approval

from acquire, once acquire approves,

the transaction will be completed.

Contact transaction:

Select “EMV”->”Transaction”->”Start

EMV Trans” to start a contact

transaction.

Insert Contact card to complete the

transaction.

MSR transaction:

Select “MSR”->”Start MSR” to start a

MSR transaction.

ViVOpay VP8300 UserManual

Swipe MSR card to complete the

transaction.

2 Firmware Upgrade

The VP8300 can be upgraded using USB interfaces.

2.1 Preparation

To update the new firmware you will need:

• PC with available USB port

• VP8300 unit

• USB to Micro USB B type cable

• VP8300 firmware update tool

• Firmware file for the desired firmware

2.2 Procedure

1. Copy the VP8300 update tool and firmware on the PC.

2. Plug in the micro-USB B type cable to VP8300, connect the USB cable

to PC USB port.

3. There should be no beep, and all four LEDs blink once.

4. Launch the VP8300 firmware update tool.

5. Cleck “Load”, and select the Firmware which would download.

6. It will download automatically.

ViVOpay VP8300 UserManual

7. Display “100% done” and device will reset.

Inhaltsverzeichnis

Andere IDTECH Zahlungsterminal Handbücher

IDTECH

IDTECH ViVOpay VP3320S Gebrauchs- und Pflegehandbuch

IDTECH

IDTECH VP6800 Bedienungsanleitung

IDTECH

IDTECH ViVOpay 4800 Bedienungsanleitung

IDTECH

IDTECH Vivopay Neo 2 Bedienungsanleitung

IDTECH

IDTECH ViVOpay VP6300 Bedienungsanleitung

IDTECH

IDTECH VIVOpay VP8800 Bedienungsanleitung

IDTECH

IDTECH ViVOpay VP5300M Gebrauchs- und Pflegehandbuch

IDTECH

IDTECH ViVOpay VP8300 Bedienungsanleitung

IDTECH

IDTECH ViVOpay VP3300BT Bedienungsanleitung

IDTECH

IDTECH ViVOpay Kiosk IV Bedienungsanleitung

IDTECH

IDTECH ViVOpay VP6800 Bedienungsanleitung

IDTECH

IDTECH ViVOpay VP3600 Bedienungsanleitung

IDTECH

IDTECH ViVOpay BTPay Mini Bedienungsanleitung

IDTECH

IDTECH VP7200 Bedienungsanleitung

IDTECH

IDTECH ViVOpay VP6800 Bedienungsanleitung

IDTECH

IDTECH vivopay kiosk iii Bedienungsanleitung

IDTECH

IDTECH ViVOpay Vend 3 Bedienungsanleitung

IDTECH

IDTECH ViVOpay VP3300BT Bedienungsanleitung

IDTECH

IDTECH ViVOpay Vendi Bedienungsanleitung

IDTECH

IDTECH VIVOpay VP8800 Bedienungsanleitung

IDTECH

IDTECH VP6800 Bedienungsanleitung

IDTECH

IDTECH ViVOpay VP3320 Bedienungsanleitung

IDTECH

IDTECH Kiosk III Bedienungsanleitung

Beliebte Zahlungsterminal Handbücher anderer Marken

PAX

PAX D180SRF Bedienungsanleitung

LinkPoint

LinkPoint AIO Bedienungsanleitung

Moneris

Moneris hispeed 6200 Bedienungsanleitung

Moneris

Moneris iWL220 Bedienungsanleitung

Ingenico

Ingenico iUC280 Bedienungsanleitung

Ingenico

Ingenico Tetra Move/5000 Bedienungsanleitung

Ingenico

Ingenico iWL250B Bedienungsanleitung

Optimum

Optimum M4230 Bedienungsanleitung

Triton

Triton RL5000 Bedienungsanleitung

Ingenico group

Ingenico group Lane/8000 Bedienungsanleitung

Gilbarco

Gilbarco FlexPay IV CRIND Installations- und Betriebshandbuch

Infinite Peripherals

Infinite Peripherals Infinea Tab Lite Bedienungsanleitung

PAX

PAX S920 Bedienungsanleitung

Ingenico

Ingenico iCT220, iCT250 Bedienungsanleitung

dejavoo

dejavoo Z Series Bedienungsanleitung

VeriFone

VeriFone VX 520 Series Bedienungsanleitung

Optomany

Optomany axept S900 Bedienungsanleitung

Skyzer

Skyzer iWL252 BLUETOOTH Bedienungsanleitung