IFM O5E5 Series Bedienungsanleitung

Operating instructions

Through-beam sensor

O5E5xx / O5S5xx

701999 / 02 06 / 2011

UKUK

1 Preliminary note

1.1 Symbols used

►Instruction

> Reaction, result

[…] Designation of pushbuttons, buttons or indications

→Cross-reference

Important note

Non-compliance can result in malfunctions or interference.

2 Functions and features

The through-beam sensor detects objects and materials without contact and

indicates their presence by a switching signal.

Range: → type label.

3 Installation

transmitter receiver

►Install the receiver (O5E...) and secure it to a bracket.

►Align the transmitter (O5S...) to the receiver and fix it.

Maximum range only with accurate alignment.

4 Operating and display elements

1: LED yellow

2: [OUT on] button

3: [OUT o󰀨] button

receiver

5 Electrical connection

The unit must be connected by a qualified electrician.

►The national and international regulations for the installation of electri-

cal equipment must be adhered to.

►Ensure voltage supply to EN 50178.

►Disconnect power.

►Connect the unit as follows:

Transmitter connector Transmitter cable *

L+









Receiver connector

PNP NPN











L+

Receiver cable *

PNP NPN











L+

* Core colours: BN = brown, BU = blue, BK = black

6 Settings

6.1 Sensitivity setting

The sensor is to switch when the object is detected

►Position the object.

receiver transmitter

►Press [OUT on] for 2 s.

> The sensitivity is set to the object. The yellow LED flashes.

►Remove the object.

receiver transmitter

►Press [OUT off].

> The sensitivity is set without object.

> The yellow LED goes out. The setting operation is completed.

The sensor is not to switch when the object is detected

►Position the object (see figure 1) and press [OUT off].

►Remove the object (see figure 2) and press [OUT on].

You can carry out the setting first without object and then with object.

6.2 Setting of maximum sensitivity

►Interrupt the light beam.

The sensor is to switch when the object is detected.

►First press [OUT on], then [OUT off].

The sensor is to switch when the object is not detected

►First press [OUT off], then [OUT on].

6.3 Setting unsuccessful

> The LED flashes quickly, 8 Hz.

> The sensor returns to the normal operating mode with unchanged values.

Possible causes

• Insufficient difference in measurements

• Max. programming time of 15 min. exceeded

6.4 Electronic lock

The unit can be locked electronically to prevent unauthorised setting. On delivery

the unit is not locked.

►Press [OUT on] and [OUT off] simultaneously for 10 s.

> Acknowledgement is indicated by a change of the LED

status.

►To unlock repeat this step. receiver

7 Operation

►Check whether the unit operates correctly.

> The green LED (transmitter) is lit when the sensor is ready for operation.

> The output is switched when the object is present. The yellow LED (receiver)

is lit.

8 Maintenance, repair, disposal

►Keep the lens of the sensor free from soiling.

►For cleaning do not use any solvents or cleaning agents which could damage

the plastic parts.

►After use dispose of the unit in an environmentally friendly way in accordance

with the applicable national regulations.

Faulty sensors must only be repaired by the manufacturer.

Technical data and further information at

www.ifm.com → Select your country → Data sheet direct:

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere IFM Zubehör Handbücher

IFM

IFM GI854S Bedienungsanleitung

IFM

IFM OJ Gebrauchs- und Pflegehandbuch

IFM

IFM Efector 200 Series Bedienungsanleitung

IFM

IFM Efector 180 IX5030 Bedienungsanleitung

IFM

IFM PM16 Series Bedienungsanleitung

IFM

IFM PI2798 Bedienungsanleitung

IFM

IFM JD Series Anwendungshandbuch

IFM

IFM PT24 Series Bedienungsanleitung

IFM

IFM OGH Bedienungsanleitung

IFM

IFM SB4 Series Bedienungsanleitung

IFM

IFM O6P7 Series Bedienungsanleitung

IFM

IFM efector200 OOF Series Bedienungsanleitung

IFM

IFM MVQ101 Anwendungshandbuch

IFM

IFM Efector 200 OJ Bedienungsanleitung

IFM

IFM SBT633 Bedienungsanleitung

IFM

IFM OG Bedienungsanleitung

IFM

IFM O5P7 Series Bedienungsanleitung

IFM

IFM Efector 200 O6E4 Bedienungsanleitung

IFM

IFM O2D54 Series Bedienungsanleitung

IFM

IFM O2D50 Series Bedienungsanleitung

IFM

IFM O4E5 Series Bedienungsanleitung

IFM

IFM OJ51 Series Bedienungsanleitung

IFM

IFM Efector 500 PI30 Bedienungsanleitung

IFM

IFM Efector200 OJ51 Series Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung