Innovative Concepts in Entertainment Hammerhead Bedienungsanleitung

OWNERSAND SERVICE MANUAL

INNOVATIVE CONCEPTS IN ENTERTAINMENT INC.

10123 MAIN STREET, CLARENCE, NY 14031

SERVICE: 1–716–759–0360

FAX: 1–716–759–0884

E–MAIL: [email protected]

INTRODUCTION.............................................. PAGE 3

GAME FEATURES

GAME PLAY

INSTALLATION................................................. PAGE 4

BEFORE YOU BEGIN

INSTALLATION

PROGRAMMINGOPTIONS ............................ PAGE 5 & 6

INTRODUCTION

USING THE PROGRAMMING OPTIONS

MAINTENANCE ............................................... PAGE 7

QUICK TROUBLESHOOTING......................... PAGE 8

GAMEREPAIR................................................. PAGE 9 – 11

OPERATIONAL BACKGROUND

TROUBLESHOOTING PHILOSOPHY

MECHANICAL REPAIR

PARTS LISTINGS ............................................ PAGE 12

SCHEMATICS.................................................. PAGE 13 – 15

WIRINGDIAGRAMS........................................ PAGE 16 – 25

TABLE OF CONTENTS

INTRODUCTION

GAMEFEATURES

Thankyouforpurchasing thenewHammerhead"game

from I.C.E. This new “WACKY” game utilizes all the

proventechnologyofit’s predecessor Smack–n–Alien. ICE

has taken out the cost but not the quality, giving the

customer a fresh look with full reliability.

Game cabinetry is stylish, yet bright. The game has been

designed to be either a back–to–back centerpiece or a

wall unit that will enhance the look of any location. Thick

16gaugemetalpanelsand marine grade waterresistant

plywoodmakethegameextremely durable. The boatbow

is made of a special high impact styrene that is easy to

maintain.

The distortion printed marquee is made of .187 PETG.This

is back printed, which will prevent the customer from

damagingtheprinting.The PETG is moredurablethan

acrylic and therefore will withstand impact better.

Electronics and sounds are the state of the art in digital

technology.Robustdesign ensures a long troublefreelife

for your game. The game is very flexible with its

programming options to allow it to be tailored to most

locations easily.

GAMEPLAY

The object of the game is to hit as many sharks as

possible in the time allowed. (Note: the player must try to

hit the sharks that are in the up position to score points)

The player does not get penalized for missing a shark.

The high score for the day will be displayed for all new

players to try and match.

(NOTE: There is a bonus shark, the shark that pops up

before game play starts. If a player hits that on he will be

awardedoneextrapoint.)

INSTALLATION

BEFORE YOU BEGIN

WARNING: WHENINSTALLINGTHISGAME,A

GROUNDEDA.C.RECEPTACLEMUSTBE USED.

FAILURETODO SO COULDRESULTIN INJURYTO

YOURSELFOROTHERS.FAILURE TOUSEA

GROUNDEDRECEPTACLECOULDALSOCAUSE

IMPROPERGAMEOPERATION, OR DAMAGETOTHE

ELECTRONICS

DONOTDEFEATORREMOVETHEGROUNDING

PRONGONTHEPOWERCORD FOR THE SAME

REASONAS GIVENABOVE. USINGAN IMPROPERLY

GROUNDEDGAMECOULD VOIDYOURWARRANTY.

HAVEAQUALIFIED ELECTRICIANCHECKYOU’REA.C.

RECEPTACLETO BE SURETHEGROUND IS

FUNCTIONINGPROPERLY.

TOOLS NEEDED

Thegamenormallycomesfully assembled and readyfor

use.

Ifhowever,youneed to disassemble orreassemblethe

marquee to the game for any reason, all that is needed is

a 5/32 securityAllen wrench.

INSTALLATION

The game comes ready to play with just a few simple

things to keep in mind.

1. When installing the game, be sure you use a

groundedA.C. outlet. If necessary, have it checked to

be sure the ground is good.

THISGAMEIS DESIGNEDTODISSIPATESTATIC

ELECTRICITYTHROUGH THEGROUNDING PLANEOF

THE GAME. IF THEA.C. GROUND DOES NOT WORK,

THEGAMECOULDDISCHARGESTATICELECTRICITY

THROUGHTHEGAMECIRCUITRY,WHICHCOULD

CAUSE DAMAGE.

Make sure the game is level after installation. It is

necessary to make sure the game is level so the

gamewillworkproperly.

Place the game into its final location and use the adjusting

CAUTION:CHECKTHATTHEA.C.VOLTAGERATING ON

THE BACK OF THE GAME MATCHES THEA.C.

VOLTAGEOFYOURLOCATION.

THE POWER SUPPLY IS NOT VOLTAGEADJUSTABLE.

TOOPERATETHEGAMEATVOLTAGES OTHERTHAN

THOSEITWASDESIGNED FOR, PLEASE CONTACT

OURSERVICEDEPARTMENTFORVOLTAGE

CONVERSIONINFORMATION.

Plug the game into theA.C. outlet and turn on power to

the game. The switch for the game is located on a power

module on the outside rear of the game.

It is now time to program your game&&..

PROGRAMMING

INTRODUCTION

TheHammerhead"gameisextremelyflexible from a programming standpoint. Thisallowsthecustomerto“fine tune” the

game to his or her exact needs.

This section will describe in detail each of the programming options and how they work.

PLEASEREADTHISSECTIONTHOROUGHLYBEFORECALLINGOURSERVICEDEPARTMENT.MOSTQUESTIONS

REGARDINGSET–UPANDOPERATION WILLBEFULLYEXPLAINED HERE.

HOW TO USE THE PROGRAMMING OPTIONS

PROGRAMMING BUTTON - Use this button to enter and exit the programming mode. Press this button once to enter the

mode, and once again to exit the mode.

SELECTBUTTON-Usethisbutton to scroll through and “step”throughthevariousoptions.

ADVANCE BUTTON-Usethisbutton to “change” the value ofaparticular option.

TICKETRESET BUTTON – Use this button to “reset” ticket counter.

SELECTBUTTON

PROGRAMMINGBUTTON

TICKETRESETBUTTON

ADVANCEBUTTON

PROGRAMMING

OPTION DEFAULT MIN / MAX DEFINITION

O 7 00 10 Volume adjustment

1 2 01 09 coins per credit switch 1

2 1 00 09 # of coin 1’s per credit switch 2

3 20 10 99 number of seconds per game

4 2 00 06 difficulty (lower = easier)

5 2 00 09 tickets just for playing

6 5 01 10 hits per tickets

7 25 00 99 ticket cap per game

8 5 00 99 minutes between attract mode

9 3 01 03 attract mode type

10 00 00 01 factory reset

NOTE: After the factory reset has been selected, the programming button must be

pressed twice to exit.

MAINTENANCE

GENERALMAINTENANCE

This game has been designed to be as trouble and

maintenancefreeaspossible.

With this in mind the only basics are to keep the game

clean. Below are the main areas to take care of with

specificdirections.

MARQUEE

TheMARQUEEshouldbecleanedwith a soapy water

solutionifcoveredwithwater–based dirt such asfood

products.After cleaning with soapy water, polish with a

commercial plastic polish or a spray furniture polish.

These have lubricating oils that condition the plastic and

keep it shiny and clear looking. Never use regular glass

cleaners as the ammonia in them actually damages the

plastic and dulls it.

Any deep scratches can be reduced or eliminated with a

scratchremovingpolishand buffingwheel.

CABINET

The cabinet plastic and decals can be cleaned with soapy

water or spray furniture polish. DO NOT use any alcohol or

petroleum based cleaners as they could damage the

plastic or printed parts.

COINMECHANISMS

The coin mechanisms should be cleaned periodically, as

they will accumulate dirt, which will cause the coins to

stick.

Remove the coin mech and clean them in a dish detergent

solution and a stiff brush. Dry thoroughly and re–install.

TICKETDISPENSERS

The biggest problem ticket dispensers have is ticket dust

blocking the optical detectors. It is a good idea to

occasionally use compressed air to remove the dust from

thedispensers.

SHARKHEAD

The sharks should be cleaned with a soapy water solution.

Be sure to wring the sponge out before cleaning. Excess

water may drip onto coil bed assembly and cause

permanentdamage.

LUBRICATION

We do not recommend the use of any lubrication

anywhereonthegame.

The only moving parts on the game are the sharks. If you

notice any sticking or binding of the sharks check the

following.

– Dirt on the solenoid shafts - Remove the solenoid

shafts, clean with isopropyl alcohol. Finish wiping

clean with a good grade of spray polish only.

– Wear - If excessive solenoid body wear is noted,

replace the solenoid coil.

QUICKTROUBLESHOOTING

GAME WILL NOT TAKE OR ADD MONEYCORRECTLY

•Micro switch not working or returning properly. Check and repair or replace as necessary.

•Bad Harnessing or connector. Check w/ohm meter and repair as necessary.

•Gameprogrammingsetincorrectly.Checkprogrammingoption and re–program ifnecessary.

Bad Main P.C. Board. Check and repair or replace as necessary.

SHARKS WILL NOT POPUP DURING GAME PLAY

•Opto Sensor is not working properly.Test and replace as necessary.

•Reflective foil is not properly in place. Reapply foil correctly.

•Bad harnessing or connector. Check w/ohm meter and repair as necessary.

•Bad Main P.C. Board. Check and repair or replace as necessary.

GAME HAS NO SOUND

•Bad speaker. Check w/ohm meter for 4 or 8–ohm load. If not within this range, replace.

•Volumelevelsetincorrectly. Check volumelevelinprogramming,and adjust if necessary.

•Bad Harnessing or connector. Check w/ohm meter and repair as necessary.

•Bad Main P.C. Board. Check and repair or replace as necessary

TICKET DISPENSER DOES NOT WORK OR WORKS IMPROPERLY

•Bad ticket dispenser. Repair or replace as necessary.

•Bad harnessing or connector. Check w/ohm meter and repair as necessary.

•Bad Main P.C. Board. Check and repair or replace as necessary.

•Game out of tickets.Add tickets

•Optical sensor on ticket dispenser dirty. Remove paper fuzz and debris with a soft brush.

NOFLORESCENTLIGHTING

•Bulbburnedout.Replacebulb.

•Electronic ballast bad. Replace ballast.

•Harness bad or harness unplugged. Check w/ohm meter and plug in, repair or replace as necessary.

•NoA.C. power to the game or Main fuse bad. Check fuse andA.C. power.

TICKETS OR HIGH SCORE DISPLAY Don’t WORK PROPERLY

•Bad Display P.C. Board. Repair or replace Display board

•BadMainP.C. Board.Repairor replace Main board.

•Bad display harnessing. Repair as necessary.

CAN’T ENTER OR EXIT PROGRAMMING OR OTHER ADJUSTMENT MODES

•Badprogrammingoradjustmentbuttons.Replace buttons. Check harnessing.

•BadMainP.C. Board.Repairor replace Main board.

GAME REPAIR

WARNING: ALWAYS REMOVE POWER TO

THE GAME BEFORE ATTEMPTING ANY

SERVICE, UNLESS NEEDED FOR SPECIFIC

TESTING.

FAILURE TO OBSERVE THIS PRECAUTION

COULD RESULT IN SERIOUS INJURY TO

YOURSELF OR OTHERS.

OPERATIONAL

BACKGROUND

The HAMMERHEAD" game has been manufactured

with modular design in mind. Almost everything in the

game can be EASILY removed for servicing. This

makes it much easier for the repairman as he / she

can work in a quieter less distracting environment

away from the Game Room floor. The game relies on

1 coil bed assembly which can be remove from the

game very easily.

Coin and low ticket sensing are done with

conventional micro switches. In all areas of critical

importance, optical sensors were developed

specifically, and optimized for their particular

application.

All P.C. Boards are made of premium quality board

material and use time proven components to assure

you of the most reliable designs possible.

We have put forth our best efforts and tested this

game extensively to assure the best possible

performance under the widest variety of operating

conditions. We are ALWAYS however interested in our

customers input for product improvement. If you have

any questions or comments please feel free to

contact our service department.

I.C.E. SERVICE DEPARTMENT

716–759–0360

NORMALBUSINESSHOURSARE:

MONDAY - FRIDAY, 8:00AMTO 5:00 PM

TROUBLESHOOTING

PHILOSOPHY

To find problems with the game, always first check

what should be obvious. See that the game is

plugged in, and that all of the fuses on the game are

good. This includes the fuse that is located INSIDE

the power module.

Next, check to see that all of the connectors are firmly

seated and that none of the wires have been pulled

out of them.

When trying to find out if specific components are bad

or not. This will help you to know if you have a

problem with a specific component, or maybe a

problem with either the wiring or the Main P.C. Board.

Use extreme caution when using probes or voltmeters

if the game is powered up. If doing continuity checks,

it is important to disconnect the harnessing at both

ends, as attached they may yield erroneous results.

If a P.C. Board is suspected as the cause of a

problem, check to see that all of the components on

the board are firmly attached. Pay special attention to

any socketed devices.

If light bulbs are suspected, swap them with a bulb

that is known to work to narrow the problem down to

either a bulb or P.C. Board.

GAME REPAIR

REPLACEMENT & REPAIR

COIL BED SERVICING

To remove the coil bed:

1. Remove the 4 bolts that hold the boat bow on to

the cabinet. The bolts are located on the

underside of the playfield, on the left & right sides

of the game.

2. Remove the 6 bolts holding the coil bed in

position as shown in the photo below.

3. Unplug the multi pin connector by twisting off.

COIL BED PARTS REPLACEMENT

Service the coil bed as follows:

Remove all the shark heads from the coil bed. To

remove sharks, turn the coil bed over so that the

coil bed is resting on the shark heads. Remove

the Allen head screw from the shaft. Cut the wire

tie and remove the locking pin. Pull the shark

heads through the coil bed.

Unplug the Sensor PCB Assembly. Remove the two

Nylok nuts holding the coil cap.

Disconnect the wires to the coil & remove.

Assemble in reverse order.

UNPLUG

REMOVE NUTS

REMOVE

SCREW

CUT WIRE TIE & REMOVE PIN

Inhaltsverzeichnis

Andere Innovative Concepts in Entertainment Arcade-Spielautomat Handbücher