Inspire Ignite Bedienungsanleitung

WHAT'S IN THE BOX

TOOLS REQUIRED

www.inspirehomeautomation.co.uk

Ignite Sma Sensor

rev 1.1

1 x Ignite Sma

Sernsor

2 x AAA

Baeries

1 x Screw

Pack

Drill + 5mm

Drill Bit

Phillips

Screwdriver

INTRODUCTION

The Ignite Sma Sensor will detect temperature, motion and

humidity to help improve the eﬀiciency of your heating. This

will link into an existing Ignite Heating System.

The Sma Sensor should not be installed in areas subject to

extended periods of high humidity, e.g. bathrooms

SPECIFICATIONS

Power Supply:

2 x AAA Alkaline Baeries

Temperature Range:

0-40°C

Humidity Range:

0-100% Rh

Motion Sensing Range:

70°@ 5 Metres - Horizontal

20° @ 5 Metres - Veical

Radio Frequency:

868 MHz

Dimensions:

68 x 68 x 23mm

RADIO SIGNAL

When choosing a location for your Sma Sensor, consider the

radio signal path. The signal will travel between units in a

straight line and will degrade both with distance and (much

more impoantly) objects that it has to pass through.

The Sma Sensor needs to connect to the Receiver (Ignite

Wireless / LITE) or Thermostat (Ignite Wired) via its internal

low power radio.

Every house is diﬀerent, and this is NOT a guarantee, but as a

guide, the units should be able to communicate with each

other through two single skin brick or stud walls.

If the above is not possible, consider moving one or more of

the system components or ask us about our Ignite Signal

Booster.

Also, the radio can be adversely aﬀected by large metal

objects such as your boiler, radiators, and mirrors. For best

peormance, ensure that your units are placed at least 1

metre away from such objects.

Fig 1 shows two possible Sensor locations, and the path that

the signal will travel to communicate between the Receiver

and Sensor. If the Sensor is located at "B", the signal will need

to go through two external walls.

If the Sensor is located at "A", it will have a significantly beer

signal as it will only have to travel through one internal wall.

Fig 2 shows another two possible positions. The Sensor located

at "B" will have the signal travelling entirely through a solid

wall. This will create a very poor signal, or no signal at all.

When moved to position "A" the signal will be considerably

stronger.

Fig 1

Fig 2

BATTERY INSTALLATION

We recommend that you pair the Sma Sensor with your

Ignite System prior to fixing it to the wall.

1. Whilst holding the back plate, rotate the outer cover

anticlockwise and remove in direction shown below

2. fit supplied baeries.

3. Secure outer cover by following Step 1 in reverse.

Fig 3

Fig 4

PAIRING INSTRUCTIONS

Put the Ignite device into pairing mode as detailed below

Ignite Wired

Press and hold 'CH MODE' and 'BOOST CH' keys

together on the Room Thermostat until C5 is

displayed.

Ignite Wireless / LITE (March 2021 onwards)

Long press BOTH buons on the Receiver until '1 and

WiFi' lights flash slowly.

Using the LEFT buon, cycle through the menu until

'CH' flashes.

Press the RIGHT buon, 'CH' will rapidly flash.

Ignite Wireless 4 channel / LITE 4 channel

(March 2021 onwards)

Long press BOTH buons on the Receiver until '1 and

WiFi' lights flash slowly.

Using the LEFT buon, cycle through the menu until

the required heating zone number flashes (1-4).

Press the RIGHT buon, this heating zone number will

now rapidly flash.

Ignite Wireless (March 2021 and earlier)

Sho press the pairing (middle) buon on the Relay

Module, this will make all three lights flash green.

Then press the CH buon, The CH buon will now

flash green.

TESTING THE SYSTEM

Ideally, the sma Sensor should be positioned at a height of

1.0 - 1.5 meters and in a high traﬀic area.

Hold the Sma Sensor in your desired location.

Press and hold /\ arrow buon for 5 seconds. The Ignite

Sma Sensor will enter into a signal strength mode.

A sweeping LED will be displayed whilst the signal detection in

in progress.

If a signal is detected, the strength will be measured from 1-5

lighting LEDs accordingly. to work eﬀectively, the signal should

be a minimum of two LEDs.

If the unit has not been paired, two outside LEDs will rapidly

flash. Please return to pairing instructions on previous page

and follow the appropriate steps to pair the Sma Sensor

Sma Sensor

Ensuring the Inspire leaf logo is at the top, press and hold \/

buon for 5 seconds. All 5 LED's will slowly flash to indicate

unit is in pairing mode.

Upon successful pairing, the centre LED on the Sma Sensor

will rapidly flash.

If pairing fails, the two outside LED's will rapidly flash. Please

try the pairing procedure again.

INSTALLATION INSTRUCTION

4. Remove outer cover by repeating step 1

5. remove baeries, hold the device in the desired position and

mark screw mounting positions

6. Drill holes and fit supplied wall plugs (if required)

7. Mount device using supplied screws

8. Fit baeries

9. Secure outer cover by following Step 1 in reverse 9

Fig 5

Fig 6

USING THE SYSTEM

To Activate the Boost, press the /\ buon twice

To Cancel the Boost, press the \/ buon twice

Sensor.

If you are adding multiple Sma Sensors, you can RENAME

them via your online account. Please login and click the unit

setup to begin. We would recommend naming them as you pair

them to the Ignite system.

Fig 7

Andere Handbücher für ignite

Inhaltsverzeichnis

Andere Inspire Zubehör Handbücher

Inspire

Inspire BOOSTER Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung

Inspire ignite Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken