Inspur NF8380M5 Bedienungsanleitung

The rack, chassis or guide rails may cause scratches, please be careful.

机柜或者服务器机箱、导轨可能造成划伤！

When installing new servers into the rack in use, please be aware of electric shock.

在正在使用的机柜中安装新服务器时，请谨防触电！

V1.0

请注意！

Warnings!

●When installing 3U or bigger servers, at least 3 people are needed.

安装3U或更大的机型时，至少需要3个人。

●During the installation process, please don’t block the vents on the server, especially the vents

on the front and rear of the server.

安装时请注意不要阻塞服务器上的通风孔，尤其是服务器前、后部的通风孔。

●Please remove the protective film on the server surface before using.

请在使用之前将服务器外壳上的保护膜撕去。

●Please leave 15cm minimum of clearance on the front and rear sides of the server for proper

ventilation.

服务器的前、后部需至少留出15厘米空间，以便于系统散热。

●Please install air baffles for the position without device installed, to make sure that the server

can get enough air flow, and to avoid air turbulence in the server room.

没有安装设备的机柜位置，请始终安装挡风盲板，以确保服务器获得足够的气流，并避免机房气流

紊乱。

●Servers are high-power electrical appliances, and they should be installed into the dedicated

cabinets with vents or professional water-cooled cabinets, to prevent system failures caused

by overheating.

服务器是高功耗电器，只能安装在带有通风孔的专用机柜，或者专业水冷机柜中，以免过热造成系

统失效。

●If it needs to install more than one device, please load from the bottom up, and load the

heaviest items first.

如果要安装多台设备，请先从机柜靠下的空位开始，并将较重的设备安装在机柜下部。

●Please note the cabinet’s bearing capacity, power supply capacity and heat dissipation

capacity, be sure not to install devices beyond the cabinet’s bearing capacity.

请注意机柜的承重、供电及散热能力，切勿安装超出机柜承载能力的设备。

●For the convenience of using the front and rear ports of the server and cabling, leave 70mm

minimum of clearance between the front end of the server and the inner side of the cabinet’s

front door, and leave 150mm minimum of clearance between the rear end of the server and

the inner side of the cabinet’s rear door.

为了便于使用服务器前、后部的接口，并便于布线，服务器前部与机柜前门内侧之间至少留出70

毫米、后部与机柜后门内侧之间至少留出150毫米距离。

Please keep this document for checking in the future.

请保留本文档，以便于日后查阅。

Inspur Rack-Mounted Server

Installation Guide

浪潮机架式服务器

上架安装指南

If the device is more than 15kg, 2 people are needed at least.

安装超过15千克的设备时，至少需要2个人！

If the device is more than 30kg, 3 people are needed at least.

安装超过30千克的设备时，至少需要3个人！

If the device is more than 50kg, 4 people are needed at least.

安装超过50千克的设备时，至少需要4个人！

15kg

30kg

50kg

机架式服务器上架安装指南 V1.0

导轨前后端视图

b) Insert the front end rivets into the post holes.

将导轨前端铆钉插入角轨孔位。

Front&Rear End of the Rail

Rack-mounted Server Installation Guide

安装导轨

Installing Rails

Install the front end of the rail to the rack.

导轨前端安装到机柜

a) Position the rail front end on the rack. Install nuts into the corresponding holes

on the rack post for screw installation.

在机柜上确定导轨前支架的安装位置，将螺母安装到角轨相应孔位，便于螺丝的

锁附

Repeat steps 1 and 2 to install the other side.

重复1、2动作，完成另一侧导轨安装

Lift the server and place its rear end on the rails first, then push the server horizontally

into the rack from the front end.

抬起服务器先将后端放入导轨上，然后从前端将服务器水平推入导轨，如下图：

Locate and tighten the screws on the left and

right handles of the server.

服务器推入机柜后，将服务器左右把手的螺

丝固定，如下图：

Installing Server

安装服务器

Install the rear end of the rail to the rack.

导轨后端安装到机柜

a) Pull the extended bracket, and insert the rear end rivets into the post holes. Please

keep the front and rear ends on the same level.

拉伸延伸架，将导轨后端铆钉插入角轨孔位，与导轨前端保持在同一水平方向。

b)Lock the screws on the front and rear ends and the 4 screws on the extended bracket.

The rail installation is complete.

锁紧前后端角轨孔位螺丝及延伸架上4颗螺丝，导轨安装完成

Rear

Front

Andere Handbücher für NF8380M5

Andere Inspur Server Handbücher

Inspur

Inspur I48 Bedienungsanleitung

Inspur

Inspur Yingxin NX5440M4 Bedienungsanleitung

Inspur

Inspur I48M6 Bedienungsanleitung

Inspur

Inspur NF3120M5 Bedienungsanleitung

Inspur

Inspur NF5486M5 Bedienungsanleitung

Inspur

Inspur Tiansuo TS860 Bedienungsanleitung

Inspur

Inspur NF5180M4 Bedienungsanleitung

Inspur

Inspur NF8480M5 Bedienungsanleitung

Inspur

Inspur NF5280M5 Bedienungsanleitung

Inspur

Inspur Yingxin Bedienungsanleitung

Inspur

Inspur NF5180M6 Bedienungsanleitung

Inspur

Inspur NF3120M5 Bedienungsanleitung

Inspur

Inspur NP3060 Bedienungsanleitung

Inspur

Inspur Yingxin Bedienungsanleitung

Inspur

Inspur NF5280M6 Bedienungsanleitung

Inspur

Inspur NF5468M5 Bedienungsanleitung

Inspur

Inspur NX5460M4 Bedienungsanleitung

Inspur

Inspur Yingxin NF5280M2 Bedienungsanleitung

Inspur

Inspur NF5488A5 Bedienungsanleitung

Inspur

Inspur Yingxin NP3020M2 Bedienungsanleitung

Inspur

Inspur NF5180M6 Bedienungsanleitung

Inspur

Inspur NF5266M5 Bedienungsanleitung

Inspur

Inspur NF5448A6 Kurzanleitung

Inspur

Inspur NF5266M6 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung