Inspur I48M6 Bedienungsanleitung

X01500A000000000

Warnings!

Please keep this document for future reference.

15kg

30kg

50kg

Watch out for the scratches that may be caused by the cabinet, chassis or rails.

Be aware of electric shock when installing the servers into the cabinet in use.

●For servers of 4U form factor or higher, at least 4 people are needed for installation.

●DO NOT block the vents on the server during installation, especially the vents on the front

and rear of the server.

●Remove the protective film from the chassis before installing servers into the rack.

●For proper ventilation, leave a minimum space of 15cm between two servers.

●For easy access of the front and rear ports and cabling, leave a minimum space of 70mm

between the front side of the server and the inner side of the cabinet’s front door, and

150mm between the rear side of the server and the inner side ofthe cabinet’s rear door.

●Always keep the air baes in place to ensure proper air flow and avoid air turbulence in the

server room.

●Installation must comply with local and regional electrical regulations. To reduce the risk of

personalinjury, fire, or damage to the server, DO NOT overload the AC supply that provides

power to the rack.

●Servers can only be deployed in dedicated cabinets with ventilation holes or specialized

cooling cabinets to avoid server failure from overheating as they are high power appliances.

●In case of multiple-server deployment, always load from bottom to top and place the heavier

server on the lower bay.

●DO NOT install devices beyond the cabinet’s load-bearing capacity, power supply capacity

and heat dissipation capacity.



For devices ≥ 15kg, it requires at least 2 people.

For devices ≥ 30kg, it requires at least 3 people.

For devices ≥ 50kg, it requires at least 4 people.

Rack-Mounted Server

Installation Guide

V1.0

Rack-Mounted Server Installation Guide

V1.0

5.A bracket is needed when the server is equipped with nodes. Install six

floating nuts into the holes next to the bottom of the rails, and then

secure the bracket to the rack with 6 screws. Make sure that the top of

the bracket stays against the bottom of the rails.

4.Repeat Step 1-3 for the other rail and the other stopper.

Note: The two rails must be installed at the same height.

The rails are applicable for square-hole (9.2*9.2 mm, 9.5*9.5mm) and

round-hole (Ø 7.1mm) racks.

Rail-Kit Components

Rails, Stoppers , Screws: M5x8 Phillips head screw (×4)

Installing the Rails

1.Align the pins on the rear bracket to the desired position of the back of the

rack. Press the locking latch as indicated by arrow ①, and then insert the

pins as indicated by arrow ②until the pins are fully engaged.

2.Follow Step 1 to install the front bracket to the front of the rack.

Note: The front end and the rear end of the rail must be installed at the same

height.

3.Install the two floating nuts into the post holes above the rear end of the

rail. Hold the stopper, and then insert and tighten the two M5x8 Phillips

head screws. Make sure the space between the top of the stopper and

the bottom of the rail is 4U.

Note: You may use either stopper 1 or stopper 2 for stopper installation.

Stopper

Option 1

Stopper

Option 2

Stopper 1 Installation

Use square nuts on square-hole posts.

Use U-nuts on round-hole posts.

Stopper 2 Installation

Note: Two washers are

needed for square-hole

posts.

Rear BracketFront Bracket Rail

①Pull and rotate the plunger on the lifting handle clockwise or

nticlockwise. Make sure the plunger does not spring back.

②Align and attach the 5 T-standos on the lifting handle to the

eyholes on the side of the server. Push the handle until the

T-standos slide nto the smaller holes. Rotate and release the

plunger until it springs ack into the chassis.

③Refer to steps ①and ②to install the other 3 lifting handles.

2.Hold the lifting handles to lift the server up onto the rails. Refer to

the installation procedure to remove the 4 lifting handles.

3. Slide the server all the way into the rack and tighten the captive

screws in the mounting ears.

Note: Keep the removed lifting handles properly for future use.

Installing the Server

1.Install the lifting handles.

Plunger

T-standoﬀ

Andere Inspur Server Handbücher

Inspur

Inspur NF3120M5 Bedienungsanleitung

Inspur

Inspur TS860M5 Bedienungsanleitung

Inspur

Inspur NE5260M5 Bedienungsanleitung

Inspur

Inspur Yingxin Bedienungsanleitung

Inspur

Inspur i24 Bedienungsanleitung

Inspur

Inspur I48M6 Bedienungsanleitung

Inspur

Inspur NF5266M5 Bedienungsanleitung

Inspur

Inspur NF5486M5 Bedienungsanleitung

Inspur

Inspur 3408 Series Merkblatt

Inspur

Inspur NF5180M6 Bedienungsanleitung

Inspur

Inspur NF8380M5 Bedienungsanleitung

Inspur

Inspur NF5488A5 Bedienungsanleitung

Inspur

Inspur NF5266M6 Bedienungsanleitung

Inspur

Inspur NF5448A6 Kurzanleitung

Inspur

Inspur NF5280M5 Bedienungsanleitung

Inspur

Inspur NP3060 Bedienungsanleitung

Inspur

Inspur NX5760M3 Bedienungsanleitung

Inspur

Inspur Yingxin NF5280M2 Bedienungsanleitung

Inspur

Inspur I48 Bedienungsanleitung

Inspur

Inspur NF5468M6 Bedienungsanleitung

Inspur

Inspur NF5280M5 Bedienungsanleitung

Inspur

Inspur NF5266M5 Bedienungsanleitung

Inspur

Inspur ON5263M5 Bedienungsanleitung

Inspur

Inspur NF5288M5 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung

Inspur i48M6 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken