Inspur NX5460M4 Bedienungsanleitung

Dear users of Inspur server,

Sincerely thank you for using Inspur server.

This manual introduces the technical characteristics, system installation and setup of the

server, and helps you to particularly understand and expediently use this server.

Please deliver the package of our product to the waste recycling station, in favor of pollution

prevention and beneting humankind.

This manual is the property of Inspur.

This User Manual is not to be copied by any group or person in any manner without the

consent of Inspur. Inspur reserves the right of revising this manual momentarily.

The information in this manual is subject to change without notice.

Please contact Inspur, if you have any questions or advice about this manual.

Inspur

December, 2015

is the registered trademark of Inspur. All the other trademarks or

registered trademarks mentioned in this manual are the property of their respective holders.

Document Version: V1.0

Release Date: 5th December. 2015

Document Introduction: 1st formal issuance

Abstract

The manual introduces issues closely related to maintenance such as specications, hardware

operation, software conguration, service terms, fault diagnosis etc. of the server.

Readers of this guide will be deemed to have abundant knowledge about the server product

and have received adequate technical training, and will not cause any personal injury or

product damage during operation and maintenance.

Target Audience

This manual mainly applies to the following personnel:

●Technical support engineers

● Product maintenance engineers

It is suggested that server maintenance operation shall be carried out by professional

engineers with related server knowledge via referring to this manual.

Table of Contents

1 Safety Instructions ......................................................................................................... 1

2 Product Overview ..........................................................................................................6

2.1Technical Specications.......................................................................................6

2.2 NX5460M4 Views ..............................................................................................6

2.3 Usage of NX5460M4 Blade Server ....................................................................7

2.4 CLR_CMOS Jumper Introduction .....................................................................8

3 BIOS Setup ....................................................................................................................9

3.1 System BIOS Setup Methods .............................................................................9

3.2 BIOS Settings .....................................................................................................10

3.3 Firmware Update ................................................................................................41

4 RAID System .................................................................................................................43

4.1 How to Enter RAID Conguration Interface......................................................43

4.2 Control Keys .......................................................................................................44

4.3 SAS RAID Settings ............................................................................................44

4.4 SATA RAID Settings ..........................................................................................47

5 Hardware Maintenance ..................................................................................................50

5.1 Tool Preparation..................................................................................................50

5.2 Parts Replacement...............................................................................................50

6 Common Faults, Diagnosis and Troubleshooting..........................................................53

6.1 Common Faults...................................................................................................53

6.2 Diagnosis and Troubleshooting Instructions.......................................................54

7 Services ..........................................................................................................................57

7.1 How to Obtain Warranty Service .......................................................................57

7.2 How to Contact Inspur........................................................................................57

8 Certications & Standards .............................................................................................59

8.1 USA FCC Declaration .......................................................................................59

8.2 CE Declaration of EU .........................................................................................59

8.3 China Environmental Labeling...........................................................................59

１

Safety Instructions

1 Safety Instructions

Warning: the following warnings indicate that there are potential dangers that may cause

property loss, personal injury or death:

1. The power supplies in the system may produce high voltages and energy hazards that

may cause personal injury. Please do not demount the cover of the host to remove or

replace any component in the system by yourself, unless otherwise informed by Inspur;

only service technicians trained by Inspur have the right to demount the cover of the

host, remove and replace the internal components.

2. Please connect the equipment to appropriate power supply, and only the type of external

power supply indicated on the electrical ratings label can be used. To protect your

equipment from damages caused by momentary spike or plunge of the voltage, please

use relevant voltage stabilizing equipment or uninterruptible power supply.

3. If you must use an extension cable, use a three-core cable with properly grounded plugs.

Observe extension cable ratings. Ensure that the total rating of all equipment plugged

into the extension cable does not exceed 80 percent of the ratings limit for the extension

cable.

4. Please be sure to use the power supply components that come with the server, such as

power lines, power socket (if provided with the server) etc. For the safety of equipment

and users, do not replace power cables or plugs randomly.

5. To prevent electric shock dangers caused by leakage in the system, please make sure

that the power cables of the system and peripheral equipment are correctly connected

to the earthed power socket. Please connect the three-core power line plug to the three-

core AC power socket that is well earthed and easy to access, be sure to use the earthing

pin of power lines and do not use the patch plug or the earthing pin unplugged with

cables. In case of the earthing conductors not installed and it is uncertain whether there

are appropriate earthing protections, please do not operate or use the equipment. Contact

and consult with the electrician.

6. Please do not push any objects into the openings of the system. Doing so may cause re

or electric shock because of internal components short circuit.

7. Please place the system far away from the cooling plate and the place with heat sources,

２

and be sure not to block the air vents.

8. Be sure not to scatter food or liquid in the system or on other components, and do not

use the product in humid and dusty environment.

9. Using an incompatible battery may cause explosion. When battery replacement is

required, please consult the manufacturer first, and choose batteries of the same or

equivalent type. Do not disassemble, crush, puncture the batteries or make the external

connection point short circuit, and do not expose them in the environment over 60°C.

Never throw them into fire or water. Please do not attempt to open or repair the

batteries, and be sure to reasonably deal with the exhausted batteries and do not put the

exhausted batteries, the circuit boards that may include batteries and other components

together with other wastes. For relevant battery recycling, please contact the local waste

recycling center.

10. Before installing equipment into the rack, please install all front and side stabilizers

on the independent rack rst; for the rack connecting with other racks, it shall install

the front stabilizers first. If you fail to install the corresponding stabilizers before

installing equipment into the rack, it may cause the cabinet to tip over in some cases,

and thus may cause personal injury. Therefore, it is necessary to install stabilizers before

installing equipment into the rack. After installing the equipment and other components

into the rack, it can only pull out one component from the rack through its sliding part

at one time. Pulling out several components at the same time may lead the rack to turn

over and cause serious personal injury.

11. Please do not move the rack by oneself. Considering the height and weight of the rack,

at least two people are needed to complete its movement.

12. Please do not directly touch the copper busbar when the rack is powered on, and it is

prohibited to directly short-circuit the copper busbar.

13. This is Grade A product, and in the living environment, it may cause radio interference.

In such case, users may need to take measures to deal with the interference.

Note: The following considerations can help avoid the occurrence of problems that may

damage the components or cause data loss, etc.

1. In case of the following cases, please unplug the power line plug from the power socket

and contact customer service department of Inspur:

３

Safety Instructions

1) The power cables, extension cables or power plugs are damaged.

2) The products get wet.

3) The products have fallen off or been damaged.

4) Objects fall into the products.

5) When operating according to the operating instructions, the products cannot

function normally.

2. If the system is affected with damp, please dispose according to the following steps:

1) Power off the equipment, disconnect them with the power socket, wait for 10 to 20

seconds, and then open the host cover.

2) Move the equipment to a well-ventilated place to dry the system at least for 24

hours and make sure that the system is fully dried.

3) Close the host cover, reconnect the system to the power socket, and then power on.

4) In case of operation failure or abnormal situation, please contact Inspur and get

technical support.

3. Pay attention to the position of system cables and power cables, wire them in places

not to be stepped on or knocked down and ensure not to place other objectives on the

cables.

4. Before removing the host cover or touching the internal components, you shall cool

down the equipment first; to avoid damaging the mainboard, please power off the

system and wait 5 seconds, and then remove the components from the mainboard or

disconnect a peripheral device from the system.

5. If there are modem, telecom or LAN options installed in the equipment, please pay

attention to the following matters:

1) In case of thunder and lightning weather, please do not connect or use the modem.

Otherwise, it may suffer from lightning stroke.

2) Never connect or use the modem in damp environment.

3) Never insert the modem or telephone cables into the socket of network interface

controller (NIC).

4) Before unpacking the product package, touching or installing internal components

or touching uninsulated cables or jacks of the modem, please disconnect the modem

cables.

6. In order to prevent the electrostatic discharge from damaging the electronic components

in the equipment, please pay attention to the following matters:

４

1) You shall conduct off the static electricity on the body before dismounting or

touching any electronic component in the equipment. You can conduct off the

static electricity on the body by touching the metal earthing objects (such as the

unpainted metal surface on the rack) to prevent the static electricity on the body

from conducting itself to the sensitive components.

2) For electrostatic sensitive components not ready to be installed for application,

please do not take them out from the antistatic package materials.

3) During the work, please touch the earthing conductor or the unpainted metal surface

on the cabinet regularly to conduct off the static electricity on the body that may

damage the internal components.

7. When dismounting the internal components with the approval of Inspur, please pay

attention to the following matters:

1) Switch off the system power supply and disconnect the cables, including all

connections of the system. When disconnecting the cables, please hold the

connector of cables and plug it out, and never pull the cables.

2) Before dismounting the host cover or touching the internal components, the

products need to be cooled down.

3) Before dismounting or touching any electronic component in the equipment, you

shall conduct off the static electricity on the body by touching the metal earthing

objectives.

4) During the dismounting process, the movement range shall not be too big, so as to

prevent damage to the components or scratching arms.

5) Carefully deal with the components and plug-in cards, and please never touch the

components or connection points on the plug-in cards. When taking the plug-in

cards or components, you should grab the edges of the plug-in cards or components

or their metal xed supports.

8. During the process of rack installation and application, please pay attention to the

following matters:

1) After the rack installation is nished, please ensure that the stabilizers have been

xed to the rack and supported to the ground, and all weight of the rack have been

fell onto the ground.

2) Always load from the bottom up, and load the heaviest items rst.

3) When pulling out the components from the rack, it shall apply force slightly to keep

５

Safety Instructions

the rack balanced.

4) When pressing down the release latch of the sliding rail of components and sliding

in or out, please be careful, as the sliding rail may hurt your gures.

5) Do not overload the AC power supply branch circuits in the rack. The total load of

the rack shall not exceed 80% of the ratings of branch circuits.

6) Ensure that components in the rack have good ventilation conditions.

7) When repairing components in the rack, never step on any other components.

６

2 Product Overview

2.1 Technical Specications

Processor

Processor type 1 ～2 Intel® Xeon Haswell-EP series processors

Platform type Grantley-EP 2S Platform

Memory

Memory type DDR4-1600/1866/2133 ECC Registered

Support RDIMM & LRDIMM

DIMM slot Qty. 24

Total capacity Support up to 1.5TB

Display controller

Controller type Integrated graphics

Network

Controller type Integrated dual gigabit Ethernet controller

HDD controller

SATA controller Support 2 2.5-inch hot-plug SAS/ SATA / SSD HDDs

RAID ●Onboard RAID controller: support RAID0，RAID1

●SAS RAID Mezz: support RAID0，RAID1，RAID5

2.2 NX5460M4 Views

General view

７

Product Overview

Front view

No. Name & Function

1～2 HDD1/HDD0

3 Handle

4 Reset button

Power button/indicator

Off: the compute node is not powered on;

Steady green: the compute node is powered on normally;

Blinking yellow: the power of computer node is in lock state for the moment, or

there is a power problem, it fails to power on.

UID button/indicator:

Used to locate the compute node in the rack;

ON/OFF: controlled through SMC remotely or manual operation.

Off: BMC initialization is complete or the compute node is not located;

Blinking blue: BMC initializing. The compute node’s BMC detects it has been

inserted and is building communication with SMC;

Steady blue: the compute node is located.

Status indicator

Off: the compute node is normal;

Blinking yellow: there is a critical alarm.

8～9 USB3.0 port

10 VGA

2.3 Usage of NX5460M4 Blade Server

NX5460M4 blade server must be used together with Inspur I9000 server; it can be used

only after being installed in I9000 server system. About how to install NX5460M4 into I9000

server, please refer to the relevant section in I9000 server user manual or the installation

diagram on the host chassis of I9000 blade server, it will not be repeated here.

Inhaltsverzeichnis

Andere Inspur Server Handbücher

Inspur

Inspur Yingxin Bedienungsanleitung

Inspur

Inspur ON5263M5 Bedienungsanleitung

Inspur

Inspur NP5540M3 Bedienungsanleitung

Inspur

Inspur I48M6 Bedienungsanleitung

Inspur

Inspur NF8380M5 Bedienungsanleitung

Inspur

Inspur NF8380M5 Bedienungsanleitung

Inspur

Inspur I48 Bedienungsanleitung

Inspur

Inspur NF5266M5 Bedienungsanleitung

Inspur

Inspur i48M6 Bedienungsanleitung

Inspur

Inspur NF5266M5 Bedienungsanleitung

Inspur

Inspur NX5460M5 Bedienungsanleitung

Inspur

Inspur Yingxin Bedienungsanleitung

Inspur

Inspur SA5212M4 Bedienungsanleitung

Inspur

Inspur NP5570M4 Bedienungsanleitung

Inspur

Inspur Yingxin NX5440M4 Bedienungsanleitung

Inspur

Inspur Tiansuo TS860 Bedienungsanleitung

Inspur

Inspur NF5180M6 Bedienungsanleitung

Inspur

Inspur i24 Bedienungsanleitung

Inspur

Inspur NF5448A6 Kurzanleitung

Inspur

Inspur NF5468M6 Bedienungsanleitung

Inspur

Inspur SA5112M4 Bedienungsanleitung

Inspur

Inspur NF5280M5 Bedienungsanleitung

Inspur

Inspur NF5280M5 Bedienungsanleitung

Inspur

Inspur NF5280M6 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung