Intel XL710-Q2 Bedienungsanleitung

Intel®Ethernet Adapters and Devices

User Guide

Overview

Welcome to the User's Guide for Intel® Ethernet Adapters and devices. This guide covers hardware and

software installation, setup procedures, and troubleshooting tips for Intel network adapters, connections, and

other devices.

Installing the Network Adapter

If you are installing a network adapter, follow this procedure from step 1.

If you are upgrading the driver software, start with step 5 .

1. Make sure that you are installing the latest driver software for your adapter. Visit Intel's support web-

site to download the latest drivers.

2. Review system requirements.

3. Insert the adapter(s) in the computer.

4. Attach the copper or fiber network cable(s).

5. Install the driver.

6. For Windows systems, install the Intel® PROSet software.

If you have any problems with basic installation, see Troubleshooting.

You can now set up advanced features, if necessary. The available features and the configuration process

varies with the adapter and your operating system.

Supported Devices

For help identifying your network device and finding supported devices, click the link below:

http://www.intel.com/support

Compatibility Notes

In order for an adapter based on the XL710 controller to reach its full potential, you must install it in a PCIe

Gen3 x8 slot. Installing it in a shorter slot, or a Gen2 or Gen1 slot, will limit the throughput of the adapter.

Some older Intel(R) Ethernet Adapters do not have full software support for the most recent versions of

Microsoft Windows*. Many older Intel Ethernet Adapters have base drivers supplied by Microsoft Windows.

Lists of supported devices per OS are available at

http://www.intel.com/support/go/network/adapter/nicoscomp.htm

Some Intel® 10 Gigabit Network Adapters and Connections support SFP+ pluggable optical modules. Please

see SFP+ Devices with Pluggable Optics

System Requirements

Before installing the network adapter, check your system for the following minimum configuration

requirements.

Hardware Compatibility

lThe latest BIOS for your computer

lOne of the following slot types, depending on your adapter:

lOne open PCI bus master slot, 32-bit or 64-bit, operating at 33 or 66 MHz

lOne open PCI-X slot operating at 66, 100 or 133 MHz(recommended)

lOne open PCI-Express slot (v1.0a or newer), 4x, 8x, or 16x.

NOTES:

lThe PRO/1000 MT Quad Port Server adapter requires a 3.3 volt only slot. It

cannot be installed in a 5.0 volt or universal slot.

lThe Intel® 10 Gigabit AT Server Adapter will only fit into x8 or larger PCI

Express slots. Some systems have physical x8 PCI Express slots that actu-

ally support lower speeds. Please check your system manual to identify the

slot.

Supported 32-bit Operating Systems

NOTE: Intel 10GbE Ethernet Adapters do not support Microsoft* Windows* 32-bit operating sys-

tems. They support 32-bit versions of Linux* and FreeBSD*.

Basic software and drivers are supported on the following operating systems:

lDOS

lSunSoft* Solaris* (drivers and support are provided by the operating system vendor)

Advanced software and drivers are supported on the following operating systems:

lMicrosoft* Windows* 7

lMicrosoft Windows 8

lMicrosoft Windows 8.1

lMicrosoft Windows 10

lLinux*, v2.4 kernel or higher

lFreeBSD*

Supported Intel® 64 Architecture Operating Systems

lMicrosoft Windows 7

lMicrosoft Windows 8

lMicrosoft Windows 8.1

lMicrosoft Windows 10

lMicrosoft Windows Server 2008 R2

lMicrosoft Windows Server 2012

lMicrosoft Windows Server 2012 R2

lRed Hat Linux

lSUSE Linux

lFreeBSD

Supported Operating Systems for Itanium-based Systems

lLinux, v2.x kernel and higher, except v2.6

Some older Intel(R) Ethernet Adapters do not have full software support for the most recent versions of

Microsoft Windows*. Many older Intel Ethernet Adapters have base drivers supplied by Microsoft Windows.

Lists of supported devices per OS are available at

http://www.intel.com/support/go/network/adapter/nicoscomp.htm

Hardware Installation

Attaching the Low Profile Bracket (Optional)

Some adapter models come with a small bracket in the product package, to be used in a low profile slot. If you

need to install the adapter in a low-profile slot, follow these instructions.

1. Before handling the adapter, ground yourself to dissipate any static charge.

2. Remove the two screws securing the standard bracket to the back side of the adapter.

3. Slide the bracket away from the adapter.

4. Slide the low profile bracket onto the adapter.

5. Attach the low profile bracket to the adapter using the screws you removed in step 2.

6. Carefully tighten the screws until they are seated. Do not over tighten.

You may re-attach the standard sized bracket in the future if necessary.

Installing the Adapter

Selecting the Correct Slot

PCI-Express Adapters

lOne open PCI-Express slot (v1.0a or newer), x4, x8, or x16.

NOTE: The Intel® 10 Gigabit AT Server Adapter will only fit into x8 or larger PCI Express slots.

Some systems have physical x8 PCI Express slots that actually support lower speeds. Please

check your system manual to identify the slot.

PCI and PCI-X Adapters

One of the following slot types, depending on your adapter:

lOne open PCI bus master slot, 32-bit or 64-bit, operating at 33 or 66 MHz

lOne open PCI-X slot operating at 66, 100 or 133 MHz(recommended)

NOTE: The PRO/1000 MT Quad Port Server adapter requires a 3.3 volt only slot. It cannot be

installed in a 5.0 volt or universal slot.

If you have configuration problems, see your computer's documentation to determine if the PCI slots are bus

master-enabled. If you get a PCI or PCI-X configuration error, select Troubleshooting in the Table of Contents.

Insert the Adapter into the Computer

1. If your computer supports PCI Hot Plug, see your computer documentation for special installation

instructions.

2. Shut down the operating system (if it's running).

3. Turn off and unplug your computer. Then remove the cover.

CAUTION: Turn off and unplug the power before removing the computer's cover. Failure to

do so could endanger you and may damage the adapter or computer.

4. Remove the cover bracket from an appropriate slot.

5. Insert the adapter, pushing it into the slot until the adapter is firmly seated.

lIf you install a 64-bit PCI adapter in a 32-bit slot, the adapter will still function, but the end of the

edge connector will be exposed and not connected. If this is the case, make sure the exposed

contacts do not touch anything that would cause an electrical problem.

lIf you are installing a PCI-Express adapter, be aware that you can install a smaller PCI-Express

adapter in a larger PCI-Express slot.

6. Secure the adapter bracket with a screw, if required.

7. Repeat steps 4 through 6 for each additional adapter to be installed.

8. Replace the computer cover and plug in the power cord.

9. Turn the power on and start your operating system.

Attaching Cables

Intel® Gigabit and 10 Gigabit Network Adapters using copper connections automatically accommodate either

MDI or MDI-X connections. The auto-MDI-X feature of Intel Gigabit Network adapters allows you to directly

connect two adapters without using a cross-over cable.

To ensure compliance with CISPR 24 and the EU's EN55024, Intel® 10 Gigabit Server Adapters and

Connections should be used only with CAT 6a shielded cables that are properly terminated according to the

recommendations in EN50174-2.

Attach an RJ45 Network Cable

Cable types

Use one of the following types of network cabling, depending on your adapter and the intended use:

NOTE: If you are using this adapter in a residential environment (at any speed), use Category 5 or

better wiring. If the cable runs between rooms or through walls and/or ceilings, it should be

plenum-rated for fire safety.

lMaximum lengths for Intel® 10 Gigabit Server Adapters and Connections that use 10GBASE-T on Cat-

egory 6, Category 6a, or Category 7 wiring, twisted 4-pair copper:

lMaximum length for Category 6 is 55 meters.

lMaximum length for Category 6a is 100 meters.

lMaximum length for Category 7 is 100 meters.

lTo ensure compliance with CISPR 24 and the EU's EN55024, Intel® 10 Gigabit Server

Adapters and Connections should be used only with CAT 6a shielded cables that are properly

terminated according to the recommendations in EN50174-2.

lFor 1000 Mbps operation (1000BaseT), use Category 5 or better (must be 4-pair wiring). Make sure you

use Category 5 cable that complies with the TIA-568 wiring specification.

NOTE: To insure compliance with CISPR 24 and the EU’s EN55024, devices based on

the 82576 controller should be used only with CAT 5E shielded cables that are properly ter-

minated according to the recommendations in EN50174-2.

lFor 100 Mbps operation (100BaseTX), use Category 5 wiring or better.

lFor 10 Mbps operation (10BaseT), use Category 3 wiring or better.

lIn all cases:

lSegment length is limited to 100 meters (328 feet, 1 inch).

lThe adapter must be connected to a compatible link partner, and may be set to auto-negotiate

speed and duplex.

lFor more information on this specification, see the Telecommunications Industry Association's web-

site: www.tiaonline.org.

CAUTION: If using less than 4-pair cabling, you must manually configure the speed and

duplex setting of the adapter and the link partner. In addition, with 2- and 3-pair cabling the

adapter can only achieve speeds of up to 100Mbps.

Insert the twisted pair, RJ45 network cable as shown.

CX4

Physical cabling characteristics for the Intel® CX4 Dual Port Server Adapter must meet IEEE Std 802.3ak,

Clause 54 specifications. The required cable connector is an MDI latch-type receptacle, as defined by IEC

61076-3-113.

The IEEE standard defines a worst-case cable length of 15 meters, based on 100 O, twinaxial cable

characteristics. However, commercial cable manufacturers may offer enhanced products that will permit

successful operation over greater distances.

Fiber Optic Cabling

Remove and save the fiber optic connector cover. Insert a fiber optic cable into the ports on the network

adapter bracket as shown.

Most connectors and ports are keyed for proper orientation. If the cable you are using is not keyed, check to

be sure the connector is oriented properly (transmit port connected to receive port on the link partner, and vice

versa).

The adapter must be connected to a compatible link partner that is operating at the same laser wavelength as

the adapter.

CAUTION: The fiber optic ports contain a Class 1 laser device. When the ports are disconnected,

always cover them with the provided plug. If an abnormal fault occurs, skin or eye damage may res-

ult if in close proximity to the exposed ports.

Connecting Fiber Optic SC Cables

The connection requirements are as follows:

lLaser wavelength: 850 nanometer (not visible).

lSX Cable type:

lMulti-mode fiber with 50 micron core diameter; maximum length is 550 meters.

lMulti-mode fiber with 62.5 micron core diameter; maximum length is 275 meters.

lConnector type: SC.

Andere Handbücher für XL710-Q2

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Intel Computerhardware Handbücher

Intel

Intel BX80570E8200 - Core 2 Duo 2.66 GHz Processor Leitfaden

Intel

Intel 460GX Bedienungsanleitung

Intel

Intel 80960MC Bedienungsanleitung

Intel

Intel BX80580Q9400 - Core 2 Quad 2.66 GHz... Bedienungsanleitung

Intel

Intel LF80537GF0484M - Cpu Core 2 Duo T7400 2.16Ghz Fsb667Mhz 4Mb Fcpga6... Bedienungsanleitung

Intel

Intel NUC 12 Pro Bedienungsanleitung

Intel

Intel 80C188EC Bedienungsanleitung

Intel

Intel 87C196CA Bedienungsanleitung

Intel

Intel VROC Bedienungsanleitung

Intel

Intel Core i7-3960X Bedienungs- und Sicherheitshinweise

Intel

Intel 915GME Bedienungsanleitung

Intel

Intel IB850 Bedienungsanleitung

Intel

Intel RMS25PB080 Einrichtungshandbuch

Intel

Intel H110 Express Bedienungsanleitung

Intel

Intel SRCS28X - RAID Controller Bedienungsanleitung

Intel

Intel 5000 Series Bedienungsanleitung

Intel

Intel LGA1155 SOCKET - THERMAL MECHANICAL S AND DESIGN GUIDELINES... Bedienungsanleitung

Intel

Intel Quad-Core Xeon Bedienungsanleitung

Intel

Intel i960 Series Bedienungsanleitung

Intel

Intel SOM-4486 ETX Module Bedienungsanleitung

Intel

Intel BV80605001914AG - Processor - 1 x Xeon X3430 Bedienungsanleitung

Intel

Intel Xeon 5500 Series Technisches Handbuch

Intel

Intel CORE 2 DUO E4000 - 3-2008 Bedienungsanleitung

Intel

Intel CORE 2 DUO MOBILE - THERMAL DESIGN GUIDE... Leitfaden

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

Advantech

Advantech ASMB-935 Series Bedienungsanleitung

Jupiter

Jupiter RAM PACK Bedienungsanleitung