Intel NUC 7 ENTHUSIAST Bedienungsanleitung
User Guide for NUC7i5BNKP, NUC7i7BNKQ
1
Intel® NUC 7 Home, a Mini PC with Windows® 10 –NUC7i5BNKP
Intel® NUC 7 Enthusiast, a Mini PC with Windows® 10 –NUC7i7BNKQ
User Guide
User Guide for NUC7i5BNKP, NUC7i7BNKQ
2
Before You Begin
CAUTION
The steps in this guide assume you’re familiar with computer terminology and with the safety
practices and regulatory compliance required for using and modifying computer equipment.
Disconnect the computer from its power source and from any network before performing any of the
steps described in this guide.
Failure to disconnect power or networks before you open the computer or perform any procedures can
result in personal injury and/or equipment damage. Some circuitry on the board can continue to
operate even though the front panel power button is off.
Follow these guidelines before you begin:
Always follow the steps in each procedure in the correct order.
Create a log to record information about your computer, such as model, serial numbers,
installed options, and configuration information.
Electrostatic discharge (ESD) can damage components. Perform the procedures described in
this chapter only at an ESD workstation using an antistatic wrist strap and a conductive foam
pad. If such a station isn’t available, you can provide some ESD protection by wearing an
antistatic wrist strap and attaching it to a metal part of the computer chassis.
Installation Precautions
When you install and test the Intel NUC, observe all warnings and cautions in the installation
instructions.
To avoid injury, be careful of:
Sharp pins on connectors
Sharp pins on circuit boards
Rough edges and sharp corners on the chassis
Hot components (such as SSDs, processors, voltage regulators, and heat sinks)
Damage to wires that could cause a short circuit
Observe Safety and Regulatory Requirements
If you don’t follow these instructions, you increase your safety risk and the possibility of
noncompliance with regional laws and regulations.
User Guide for NUC7i5BNKP, NUC7i7BNKQ
3
This guide tells you how to:
•
Upgrade system memory
•
Change/install an M.2 SSD
•
Use a VESA mount bracket
•
Connect power
•
Set up Microsoft® Windows® 10
•
Install the latest device drivers and software
•
Recover the operating system
Open the Chassis
Unscrew the four corner screws on the bottom of the chassis and lift the cover.
User Guide for NUC7i5BNKP, NUC7i7BNKQ
4
Upgrade System Memory
The Intel NUC Mini PCs NUC7i5BNKP and NUC7i7BNKQ have two 260-pin DDR4 SO-DIMM sockets,
that include pre-installed memory.
Pre-installed memory
NUC7i5BNKP
Two 4GB memory modules
NUC7i7BNKQ
Two 8GB memory modules
To upgrade memory, be sure to select memory modules that meet these requirements:
1.2V low voltage memory
2133 MHz SO-DIMMs
Non-ECC
Find compatible memory modules in the Intel Product Compatibility Tool:
NUC7i5BNKP
NUC7i7BNKQ
To upgrade or add memory, follow these steps:
1. Observe the precautions in "Before You Begin" on page 2.
2. Turn off all peripheral devices connected to the computer. Turn off the computer and
disconnect the power cord.
3. Remove the computer’s bottom chassis cover.
Upgrade to different memory
a. Remove the pre-installed memory module
i. Gently spread the retaining clips at each end of the memory socket, which causes
the module to pop out of the socket (C).
ii. Holding the module by the edges, lift it away from the socket, and store it
in an anti-static package.
b. Install the new memory module
i. Align the space at the bottom edge of the memory module with the key in
the socket.
ii. Insert the bottom edge of the module at a 45 degree angle into the socket
(A).
iii. When the module is inserted, push down on the outer edges of the
module until the retaining clips snap into place (B). Make sure the clips
are firmly in place (C).
User Guide for NUC7i5BNKP, NUC7i7BNKQ
5
Install an additional memory module
a. Align the space at the bottom edge of the memory module with the key on the socket.
b. Insert the bottom edge of the module at a 45 degree angle into the socket (A).
c. When the module is inserted, push down on the outer edges of the module until
the retaining clips snap into place (B). Make sure the clips are firmly in place (C).
4. Reinstall and reconnect any parts you removed or disconnected to reach the memory sockets.
5. Replace the computer’s cover and reconnect the power cord.
Changing an M.2 SSD
The Intel NUC Kits NUC7i5BNKP and NUC7i7BNKQ support either an 80mm or 42mm SSD. Both mini
PCs come pre-installed with an m.2 SSD.
Pre-installed M.2
NUC7i5BNKP
One 256GB Intel® 600p NVMe SSD
NUC7i7BNKQ
One 512GB Intel® 600p NVMe SSD
Find compatible M.2 SSDs in the Intel Product Compatibility Tool
NUC7i5BNKP
NUC7i7BNKQ
To Change an M.2 SSD:
1. Remove the small silver screw from the 80mm or 42mm metal standoff on the board (A).
2. Remove the pre-installed SSD from the connector.
3. Align the space at the bottom of the new M.2 SSD to the key on the connector.
4. Insert the bottom edge of the M.2 SSD into the connector (B).
5. Secure the card to the standoff with the small silver screw (C).
User Guide for NUC7i5BNKP, NUC7i7BNKQ
6
Close the Chassis
After all components have been installed, close the Intel NUC chassis. Intel recommends this be done
by hand with a screwdriver to avoid over-tightening and possibly damaging the screws.
User Guide for NUC7i5BNKP, NUC7i7BNKQ
7
Attach and Use the VESA Bracket (Optional)
Follow these instructions to attach and use the VESA mount bracket:
1. Using the four small black screws that are included in the box, attach the VESA bracket to the
back of the monitor or TV.
2. Attach the two slightly larger black screws to the bottom chassis cover of the Intel NUC.
User Guide for NUC7i5BNKP, NUC7i7BNKQ
8
3. Slide the Intel NUC onto the VESA mount bracket.
Power Adapters
Country-specific power plug adapters are included in the box.
1. Choose the correct adapter for your region.
Plug
Code
US
UK
EU
AUS
Country
United States
United Kingdom
European Union
Australia
Plug
Code
CHN
IND
KOR
ARG
Country
China
India
South Korea
Argentina
User Guide for NUC7i5BNKP, NUC7i7BNKQ
9
Plug
Code
BRA
Country
Brazil
2. Slide the adapter (B) onto the power plug, locking it into place (A).
User Guide for NUC7i5BNKP, NUC7i7BNKQ
10
3. Connect AC power.
Set Up Microsoft® Windows® 10
Microsoft Windows 10 is already installed on the Intel NUC. The first time you start the computer,
you’re guided through the Windows 10 setup steps, including:
Selecting your region and language.
Accepting the Microsoft Windows license terms.
Personalizing Windows and assign a PC Name.
"Get Online" dialog to pick a wireless network (this step is optional).
Choosing Express Settings or Customize.
Assigning a User Name and Password.
Reinstalling the Operating System
If you upgrade or replace the computer’s drive, you may need to install a new version of the operating
system. See these resources:
Supported Operating Systems
Windows Setup Guide
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Andere Intel Desktop Handbücher
Intel
Intel NUC 13 Pro Kit NUC13ANHv7 Bedienungsanleitung
Intel
Intel NUC8i5BEH Bedienungsanleitung
Intel
Intel NUC 12 Pro Kit NUC12WSHi3 Bedienungsanleitung
Intel
Intel SR4850HW4 - Server Platform - 0 MB RAM Bedienungsanleitung
Intel
Intel NUC Kit DE3815TYKHE Bedienungsanleitung
Intel
Intel NUC Kit NUC5PGYH Bedienungsanleitung
Intel
Intel NUC 8 Mainstream-G NUC8i5INH Konfigurationshandbuch
Intel
Intel NUC7 Home Bedienungsanleitung
Intel
Intel NUC Kit NUC5PGYH Bedienungsanleitung
Intel
Intel NUC 7 Essential Bedienungsanleitung
Intel
Intel Compute Stick STK1A32SC Bedienungsanleitung
Intel
Intel NUC7i3BNHXF Bedienungsanleitung
Intel
Intel Euclid Bedienungsanleitung
Intel
Intel TIGW1U - Carrier Grade Server Bedienungsanleitung
Intel
Intel NUC 8 Mainstream-G NUC8i7INH Bedienungsanleitung
Intel
Intel NUC6CAY Montageanleitung
Intel
Intel NUC7CJYSAL Bedienungsanleitung
Intel
Intel NUC5i5RYK Bedienungsanleitung
Intel
Intel NUC7CJYS Kurzanleitung zur Einrichtung
Intel
Intel Learning Series Bedienungsanleitung
