Interlogix SDX-135Z Bedienungsanleitung

Attention: Please take a few minutes to thoroughly read this user guide which should be

saved for future reference.

NOTE: Leave this user guide with the home owner.

You do NOT need a home wi-fi system to use these units. Multiple wireless units create

their own independent wireless detector network, in addition to wireless connection with a

compatible panel.

SDX-135Z

Wireless Smoke Detector with Heat

and Freeze Sensor User Guide

Thank you for purchasing this Interlogix smoke detector

This model is powered by a non-replaceable, long life sealed lithium battery system, and

includes SMART HUSH®Control to temporarily silence nuisance alarms. It is capable of

Wireless Interconnect with compatible units, and can also communicate with an appropriate

panel.

READ SECTION 9: Installation / Activation / Wireless, before powering the units.

You do NOT need a home wi-fi system to use these units. Multiple wireless units

create their own independent wireless detector network.

Teach children how to respond to the alarm and that they should never play with the unit. Your

Interlogix smoke detector was designed for use in a residential environment. It is not designed

for use in a recreational vehicle (RV) or boat.

NOTE: Please thoroughly read this user guide and save the document for future reference and

to pass on to any subsequent owner.

The National Fire Protection Association (NFPA) and the manufacturer recommend replacing

this detector ten years from the date code on back of the detector.

Customer Service: 1-855-286-8889

Please write down the below information and have this at hand when you call.

Model (on back): _________________

Date Code (on back): _________________

Date of Purchase: _________________

Where Purchased: _________________

Date to Replace: _________________

Contents

1. Smoke Alarm: What To Do When The Alarm Sounds.....................................................4

2. Carbon Monoxide Alarm: What To Do When The Alarm Sounds .................................5

3. Other Detector Visual And Audible Indicators .................................................................6

4. Troubleshooting Guide .......................................................................................................8

5. Introduction, Product Features & Specifications............................................................10

6. Limitations Of Smoke Detectors......................................................................................14

7. Recommended Locations For Smoke Detectors ...........................................................15

8. Locations To Avoid ...........................................................................................................17

9. Installation / Activation / Wireless ...................................................................................18

9.1 Set Up A Wireless Detector Network (Wireless Interconnect) ..............................................19

9.2 Adding Detectors to an Existing Wireless Interconnected Network .....................................21

9.3 Resetting a Detector’s Wireless Interconnect Settings .........................................................22

10. Enrolling a Detector With a Panel ……………………………………………………..........23

11. Operation and Testing……………………………………………………..............................24

12. Recognizing Nuisance Alarms ………………………………………….............................26

13. Battery …………………………………………....................................................................27

14. Permanently Disable Detector / Discharge Battery ......................................................28

15. Cleaning Your Detector ……………………......................................................................29

16. Good Safety Habits ……………………........................................................................… 30

17. Service And Warranty …………………........................................................................… 33

1. Smoke Alarm: What To Do When the Alarm Sounds

Smoke alarm pattern is three long beeps, a 1.5 second pause, and three long beeps repeating.

The red LED blinks in time with alarm pattern.

•Alert small children in the home as well as anyone else that might have difficulty recognizing the

importance of the alarm sounding or that might have difficulty leaving the area without help.

•Leave immediately by your escape plan. Every second counts, so don’t waste time getting dressed or

picking up valuables.

•In leaving, don’t open any inside door without first feeling its surface. If hot, or if you see smoke seeping

through cracks, don’t open that door! Instead, use your alternate exit. If the inside of the door is cool,

place your shoulder against it, open it slightly and be ready to slam it shut if heat and smoke rush in.

•If the escape route requires you to go through smoke, stay close to the floor where the air is cleaner.

Crawl if necessary, and breathe shallowly through a cloth, wet if possible.

•Once outside, go to your selected meeting place and make sure everyone is there.

•Call the fire department from your cell phone outside, or from your neighbor’s home-not from yours!

•Don’t return to your home until the fire officials say that it is all right to do so.

•There are situations where a smoke alarm may not be effective to protect against fire as stated in the

NFPA Standard 72. For instance:

a) smoking in bed

b) leaving children home alone

c) cleaning with flammable liquids, such as gasoline

NOTE: See Section RECOGNIZING NUISANCE ALARMS, for nuisance alarm situations.

2. Carbon Monoxide Alarm: What To Do When the

Alarm Sounds

NOTE: This is not a carbon monoxide (CO) alarm, but will receive and transmit a CO alarm signal

(four quick beeps repeating every 5 seconds) from an interconnected CO or combination smoke /

CO alarm/detector.

Carbon monoxide (CO) alarm pattern is four quick beeps repeating every 5 seconds. The red LED

blinks in time with alarm pattern.

WARNING: CARBON MONOXIDE ALARM ACTIVATION INDICATES THE PRESENCE OF

CARBON MONOXIDE (CO) AT HIGH CONCENTRATIONS WHICH CAN KILL YOU.

1) Operate the Test/Hush button. NOTE: Pressing the button on the initiating alarm unit (green LED flash-

ing every second) will silence the alarm notification, including all interconnected units. If the unit goes

into alarm mode again within six minutes, it is sensing high levels of CO which can quickly become a

dangerous situation.

2) Call your emergency services (Fire Department or 911).

EMERGENCY PHONE #: _______________________

3) Immediately move to fresh air — outdoors or by an open door / window. Do a head count to check that

all persons are accounted for. Alert small children in the home as well as anyone else that might have

difficulty recognizing the importance of the alarm sounding or that might have difficulty leaving the area

without help. Do not reenter the premises nor move away from the open door/window until the emergen-

cy services responders have arrived, the premises have been aired out, and your alarm remains in its

normal condition.

4) After following steps 1-3, if the alarm reactivates within a 24 hour period, repeat steps 1-3 and call a

qualified appliance technician to investigate sources of CO from fuel burning equipment and appliances,

and to inspect for proper operation of equipment.

If problems are identified during this inspection, have the equipment serviced immediately. Note any com-

bustion equipment not inspected by the technician and consult the manufacturer’s instructions, or contact

the manufacturer directly for more information about CO safety and the equipment. Make sure that motor

vehicles are not, or have not been, operating in a garage attached or adjacent to the residence. Never

restart the source of a CO problem until it has been corrected. Never ignore the sound of the alarm!

NOTE: See Section RECOGNIZING NUISANCE ALARMS, for nuisance alarm situations.

3. Other Detector Visual and Audible Indicators

Operational Mode Visual Indications Audible Indications Action/Note:

Normal Operation

(standby)

One GREEN LED blink

every 60 seconds.

Freeze Warning One RED LED blink

every 20 seconds.

None None. Flashing continues

while condition exists.

Tamper Condition One RED LED blink

every 30 seconds

(after a 3 minute

delay).

Detector chirps once when tamper

condition is rst sensed, then the

detector will chirp every 30 seconds

after a 3 minute delay.

Reattach detector to its trim

plate, otherwise ashing and

chirping will continue while

condition exists.

System Test Mode Rapidly ashing RED

LED for 10 seconds

duration

1 detector chirp when magnet

detected, 2 detector chirps when System

Test mode enabled

Hold magnet next to button

for 4 seconds. See Figure 5.

Local Detector Test

(button press when

no alarm condition

is present)

Flashes RED, AMBER,

GREEN, then current

protocol

Temporal T3 pattern Allow completion of test or

perform button press to

cancel, return to normal

operation

System Detector Test

(button press in System

Test Mode when no

alarm condition is

present)

Flashes RED, AMBER,

GREEN, then current

protocol on each

detector in the network

Temporal T3 pattern Allow completion of test or

perform button press to

cancel, return to normal

operation.

Operational Mode Visual Indications Audible Indications Action/Note:

Smoke/Heat Alarm

Memory (detector has

experienced an alarm

event within the last

hour)

Alternating ashing

RED and AMBER

LEDs. 1 second RED/1

second AMBER/ 10

seconds OFF,

repeating for 1 hour

None Press test button to clear alarm

memory, or allow 1 hour time out

to return to normal operation.

NOTE: standard test sequence

will follow. (Push/release button

again to cancel test).

Smoke Alarm Hush

Mode (SMART HUSH

CONTROL)

Red LED blinks

every 2 sec.

After button push: Smoke alarm

pattern stops. (If there is too

much smoke, smoke alarm

pattern continues.)

This feature is to be used

only when a known alarm

condition, such as smoke from

cooking, activates the alarm.

Locate None After button push on non-ini-

tiating unit, only initiating unit

continues alarm pattern.

Use this to quickly locate the

alarm source and determine if

alarm is nuisance or real.

Initiating Alarm Detector

(multiple detectors in an

interconnected system)

Green LED blinks once

per sec indicating that

this is the unit

initiating the alarm in

an interconnected,

multiple detector,

system.

Unit in Smoke Alarm mode. During alarm, the initiating alarm

red blink will be interrupted by a

green blink.

4. Troubleshooting Guide

Trouble Condition Visual Indications Audible Indications Action:

Fault Mode/Fatal

Error

One AMBER

LED blink every 5

seconds.

Detector chirps

every 30 seconds.

1. Push the Test/Hush button once to attempt to

reset the detector.

The RED LED will blink out an Error Code

(number of blinks) when the Test/Hush button

is pushed/released once.Report the number of

blinks to Customer Service, if needed.

2. Clean your detector. See “Cleaning Your

Detector” for instructions.

3. Remove detector from service. If fatal error

cannot be cleared, permanently discharge and

decommission the detector.

Network Error

(if a detector loses

wireless interconnect

connection due to

loss of signal)

One AMBER

LED blink every 5

seconds.

Detector chirps every

30 seconds. (NOTE:

chirps only occur if

network includes more

than 2 detectors.)

Remove device from mounting bracket, and try

rotating and re-installing the device in a different

orientation on the mounting bracket. This might

align the antenna in a better position.

1. Push the Test/Hush button once to silence the

audible indication for 24 hours at a time.

The RED LED will blink out an Error Code

(number of blinks) when the Test/Hush button

is pushed/released once. Report the number of

blinks to Customer Service, if needed.

2. Follow instructions in “Resetting a Detec-

tor’s Wireless Interconnect Settings.”, then

attempt to rejoin the network by following the

instructions in ”Adding Detectors to an Existing

Wireless Interconnected Network .”*If the error

persists, remove, discharge, and replace the

detector as soon as possible.

Network Error due to

loss of radio

(CCI supervision)

One AMBER

LED blink every 5

seconds.

Detector chirps every

30 seconds, regardless

of the number of

detectors in the

network.

1. Push the Test/Hush button once to silence the

audible indication for 24 hours at a time.

The RED LED will blink out an Error Code (4

blinks) when the Test/Hush button is pushed/

released once. Report the number of blinks to

Customer Service, if needed.

2. Remove, discharge, and replace the detector

as soon as possible.

Trouble Condition Visual Indications Audible Indications Action:

Low Battery One AMBER LED blink

every 5 seconds.

Detector chirps every 60

seconds

Remove, discharge, then dispose of

detector. Replace as soon as possible.

End of Detector

Life (EOL)

One AMBER LED blink

every 5 seconds.

Double detector chirp

every 30 seconds.

The RED LED will blink out an Error

Code of 9 blinks. Start of EOL will be

delayed if Night Detect is active.

Hush (for Network

Error, End of Life)

One AMBER LED blink

every 5 seconds.

Chirp temporarily

silenced for 24 hours.

Push the Test/Hush button to

initiate Hush for 24hrs.

Sensor Clean-

liness

Level (Clean-Me

Indication)

AMBER LED Clean-Me

blink sequence after

TESTING (PUSH TO TEST

BUTTON) temporal pattern

per “Operation and Testing”

None 1. Push the Test/Hush button to initiate

detector test. Following the temporal

patterns, the AMBER LED will blink

the cleanliness status of the detector:

0-1: Unserviceable fault; remove,

discharge, and replace the detector.

2-3: Insensitive; requires cleaning per

“Cleaning Your Detector” section.

4-7: Normal Sensitivity

8-9: Too sensitive, requires cleaning

per “Cleaning Your Detector” section.

Alarm Fault: Number of RED LED Blinks (short

duration blinks) Wireless Fault: Number of RED LED Blinks (long duration

blinks)

7: Push to Test

8: Memory

9: Life Expiration

10: Smoke Chamber

12: Temperature Sensor Supervision

14: Smoke Drift Compensation

2: Fault Coordinator

3: Fault RFD

4: CCI Supervision

5: RFD Check In

6: RFD Time Sync

5. Introduction, Product Features and Specifications

Introduction

The Interlogix SDX-135Z supervised photoelectric smoke detector with heat and freeze sensors is a

self-diagnostic Learn Mode detector with wireless interconnection, 10-yr sealed battery and sensor

life, built-in sounder, diagnostic/status LED, integrated fixed temperature and rate-of-rise heat sensor

and a pre-freeze condition indicator.

The SDX-135Z uses a 319.5MHz transmitter for communication to the control panel and a 915MHz

transceiver for interconnection communication between networked detectors. Up to 24 detectors can

be a part of the same interconnected network. The dual transmitter design ensures interconnection

integrity is maintained independent of control panel status. Because of this unique design the SDX-

135Z is multi-listed to UL217, UL268, and ULC-S531 requirements.

The SDX-135Z wireless smoke detector with heat and freeze sensor is compatible with Simon XTi-5

and Advisor One Interlogix Learn Mode panels. Refer to control system / panel installation instruc-

tions for compatible panel information.

The SDX-135Z uses 10-year sealed-in lithium batteries ensuring continuous operation over the 10

year life of the detector. This eliminates worry about battery removal or unauthorized deactivation

of the detector. The self-activation feature activates the detector when attached to the mounting

bracket. At the end of detector life, the unit will chirp and send communication back to control panel,

indicating the detector is in need of replacement (see Troubleshooting Guide).

To help identify the date to replace the detector, a label has been affixed to the side of the detector.

Write the “Install date” in the space provided, and then write in the “Replace by” date (10 years from

initial power up) in permanent marker on the label prior to installing the detector.

Andere Handbücher für SDX-135Z

Inhaltsverzeichnis

Andere Interlogix Zubehör Handbücher

Interlogix

Interlogix RF711I4 Montageanleitung

Interlogix

Interlogix International ShatterPro Montageanleitung

Interlogix

Interlogix Wireless ShatterPro 5845 Bedienungsanleitung

Interlogix

Interlogix ShatterPro 60-873-95 Bedienungsanleitung

Interlogix

Interlogix ShatterPro Montageanleitung

Interlogix

Interlogix HDX-135-345 Bedienungsanleitung

Interlogix

Interlogix TX-E611 Montageanleitung

Interlogix

Interlogix 868 GEN2 Montageanleitung

Interlogix

Interlogix ShatterPro II Bedienungsanleitung

Interlogix

Interlogix SENTROL 1045T Series Bedienungsanleitung

Interlogix

Interlogix RCR-REX Bedienungsanleitung

Interlogix

Interlogix FlexPI Bedienungsanleitung

Interlogix

Interlogix International Shock Sensor Bedienungsanleitung

Interlogix

Interlogix SDX-135Z-433 Bedienungsanleitung

Interlogix

Interlogix 319.5 Bedienungsanleitung

Interlogix

Interlogix ADC-IS-300-LP Bedienungsanleitung

Interlogix

Interlogix TX-C series Bedienungsanleitung

Interlogix

Interlogix HDX-135 Bedienungsanleitung

Interlogix

Interlogix HDX-135Z-433 Bedienungsanleitung

Interlogix

Interlogix VE700 series Montageanleitung

Interlogix

Interlogix 60-886-95 Bedienungsanleitung

Interlogix

Interlogix RF-1012-07-5 Montageanleitung

Interlogix

Interlogix VE700AM Series Montageanleitung

Interlogix

Interlogix RF-1110-07-1 Montageanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung