Interlogix NS3552-8P-2S-V2 Bedienungsanleitung

NS3552-8P-2S-V2 User

Manual

P/N 1073552-EN • REV B• ISS 25JAN19

Interlogix is part of UTC

Climate, Controls & Security, a unit of United Technologies

Corporation

.Specifications subject to change without notice.

Trademarks and patents

Trade names used in this document may be trademarks or registered trademarks of the

manufacturers or vendors of

the respective products.

Manufacturer

Interlogix

2955 Red Hill Avenue, Costa Mesa, CA 92626

-5923, USA

Authorized EU manufacturing representative:

UTC Fire & Security B.V.

Kelvinstraat 7, 6003 DH Weert, The Netherlands

Version

This document applies to

NS3552-8P-2S-V2.

FCC compliance

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

mus

t accept any interference received, including interference that may cause undesired

operation.

FCC compliance

Class A:

This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in acc

ordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at hi

s own expense.

Canada

This Class A digital apparatus complies with CAN ICES

-003 (A)/NMB-3 (A).

Cet appareil numérique de la classe A est conforme à la norme CAN ICES

-003

(A)/NMB

-3 (A).

ACMA compliance

Notice!

This is a Class A product. In a domestic environment this product may cause

radio interference in which case the user may be required to take adequate measures.

Certification

EU directives

This product and

-if applicable -the supplied accessories too are marked with "CE" and

comply

therefore with the applicable harmonized European standards listed under the

EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU.

2012/19

/EU(WEEE directive):Products marked with this symbol cannot be disposed of

as unsorted municipal waste in the

European Union. For proper recycling, return this

product to your local supplier upon the purchase of equivalent new equipment, or

dispose of it at designated collection points. For more information see:

www.recyclethis.info.

Product warnings and

disclaimers

THESE PRODUCTS ARE INTENDED FOR SALE TO, AND INSTALLATION BY, AN

EXPERIENCED SECURITY PROFESSIONAL. UTC FIRE & SECURITY CANNOT

PROVIDE ANY ASSURANCE THAT ANY PERSON OR ENTITY BUYING ITS

PRODUCTS, INCLUDING ANY “AUTHORIZED DEALER”

OR “AUTHORIZED

RESELLER”

, IS PROPERLY TRAINED OR EXPERIENCED TO CORRECTLY INSTALL

SECURITY RELATED PRODUCTS.

For more information on warranty disclaimers and product safety information, please

check www.firesecurityproducts.com

/policy/product-warning/ or scan the following code:

Contact information and

manuals/ tools/ firmware

For contact information and to download the latest manuals, tools, and firmware, go to the web

site of your region.

Americas: www.interlogix.com

EMEA: www.firesecurityproducts.com

Manuals are

available in several languages

Australia/New Zealand: www.utcfs.com.au

NS3552-8P-2S-V2 User Manual 1

Content

Important information 4

Chapter 1 Introduction 5

Package contents 5

Product description 5

Product applications 9

Product features 10

Product specifications 14

Chapter 2 Installation 19

Hardware description 19

Installing the industrial managed switch 26

Cabling 29

Chapter 3 Switch management 35

Requirements 35

Management access overview 35

CLI mode management 36

Web management 38

SNMP-based network management 38

Chapter 4 Web configuration 40

Main web page 42

System 43

DHCP server 67

UDLD 79

Simple Network Management Protocol (SNMP) 81

Port management 91

Link aggregation 98

VLAN 106

Spanning Tree Protocol (STP) 131

Multicast 149

Quality of Service (QoS) 172

Access Control Lists (ACL) 195

Authentication 209

Security 243

MAC address table 259

LLDP 265

Network diagnostics 278

Loop protection 283

RMON 285

Ring 294

Power over Ethernet (PoE) 307

Port identification 319

2 NS3552-8P-2S-V2 User Manual

Chapter 5 Command line interface 320

Accessing the CLI 320

Telnet login 320

Chapter 6 Command line mode 321

System Command 322

IP Command 328

Port Management Command 334

MAC Address Table Command 338

VLAN Configuration Command 341

Private VLAN Configuration Command 348

Security Command 350

Spanning Tree Protocol Command 396

Link Aggregation Command 405

Link Aggregation Control Protocol Command 407

LLDP Command 410

LLDP MED Command 414

Thermal Command 418

PoE Command 419

Ethernet Virtual Connections Command 420

Ethernet Protection Switching Command 425

Maintainence entity End Point Command 426

Quality of Service Command 433

Mirror Command 446

Configuration Command 447

Firmware Command 448

UPnP Command 448

MVR Command 450

Voice VLAN Command 453

Ethernet Ring Protection Switching Command 458

Loop Protect Command 462

IPMC Command 464

VLAN Control List Command 472

SMTP Command 476

DIDO Command 478

Show Command 482

Chapter 7 Switch operation 487

Address table 487

Learning 487

Forwarding and filtering 487

Store-and-forward 487

Auto-negotiation 488

NS3552-8P-2S-V2 User Manual 3

Chapter 8 Troubleshooting 489

Appendix A Networking connection 491

Glossary 493

4 NS3552-8P-2S-V2 User Manual

Important information

Limitation of liability

To the maximum extent permitted by applicable law, in no event will UTCFS be liable

for any lost profits or business opportunities, loss of use, business interruption, loss of

data, or any other indirect, special, incidental, or consequential damages under any

theory of liability, whether based in contract, tort, negligence, product liability, or

otherwise. Because some jurisdictions do not allow the exclusion or limitation of liability

for consequential or incidental damages the preceding limitation may not apply to you.

In any event the total liability of UTCFS shall not exceed the purchase price of the

product. The foregoing limitation will apply to the maximum extent permitted by

applicable law, regardless of whether UTCFS has been advised of the possibility of

such damages and regardless of whether any remedy fails of its essential purpose.

Installation in accordance with this manual, applicable codes, and the instructions of the

authority having jurisdiction is mandatory.

While every precaution has been taken during the preparation of this manual to ensure

the accuracy of its contents, UTCFS assumes no responsibility for errors or omissions.

Advisory messages

Advisory messages alert you to conditions or practices that can cause unwanted

results. The advisory messages used in this document are shown and described below.

WARNING: Warning messages advise you of hazards that could result in injury or loss

of life. They tell you which actions to take or to avoid in order to prevent the injury or

loss of life.

Caution: Caution messages advise you of possible equipment damage. They tell you

which actions to take or to avoid in order to prevent damage.

Note: Note messages advise you of the possible loss of time or effort. They describe

how to avoid the loss. Notes are also used to point out important information that you

should read.

NS3552-8P-2S-V2 User Manual 5

Chapter 1

Introduction

The description of the IFS NS3552-8P-2S-V2 model is as follows:

 Industrial L2+ 8-port 10/100/1000T 802.3at PoE

 + 2-port 100/1000X SFP managed switch

Unless specified, the term “industrial managed switch” mentioned in this user manual

refers to the NS3552-8P-2S-V2.

Package contents

Open the box of the industrial managed switch and carefully unpack it. The box should

contain the following items:

 The industrial managed switch × 1

 Quick installation guide × 1

 DIN rail kit x 1

 Wall mounting kit x 1

 RS232 console cable x 1

 SFP dust-proof cap x 2

 RJ45 dust-proof cap x 9

If any of these are missing or damaged, contact your dealer immediately. If possible,

retain the carton including the original packing materials for repacking the product in

case there is a need to return it to us for repair.

Product description

Centralized Power Management for Gigabit Ethernet Networking

To fulfill the demand of higher power required PoE network applications with Gigabit

speed transmission, the industrial managed switch features high performance Gigabit

IEEE 802.3af PoE (Up to 15.4 W) and IEEE 802.3at PoE Plus (Up to 30.8 W) on all

Chapter 1:Introduction

6NS3552-8P-2S-V2 User Manual

ports. A maximum of 30.8 W is available on each Gigabit port of the industrial managed

switch for powering per PD, with a maximum PoE delivery of 240 Wfor all ports in order

to satisfy the increasing needs of power consumption by PDs. Providing Gigabit

throughput and high power supply, the industrial managed switch optimizes the

installation and power management of network devices such as 11n wireless access

points (AP) with Gigabit PoE LAN port, security PTZ / Speed Dome network video

camera, large screen PoE Video phones, thin-clients,etc.

Intelligent powered device alive check

The industrial managed switch can be configured to monitor connected powered device

(PD)status in real time via aping action. After the PD stops working and responding,

the industrial managed switch resumesthe PoE port power and puts the PD back to

work. The industrial managed switch greatly enhancesthe network reliability through

the PoE port resetting the PD’s power source and reducing the administrator

management burden.

PoE schedule for energy saving

Under the trend of energy saving worldwide and contributing to environmental

protection, the industrial managed switch can effectively control the power supply in

addition to its capability of providing high Watt power. The “PoE schedule” function

helps you to enable or disable PoE power feeding for each PoE port during specified

time intervals,and is a powerful function to help SMBs or enterprises save power and

money.

Chapter 1: Introduction

NS3552-8P-2S-V2 User Manual 7

Cost-effective IPv6 managed Gigabit switch solution for SMB

To fulfill the demand of IPv6 (Internet Protocol version 6) network infrastructure, the

industrial managed switch supports both IPv4 and IPv6 management functions. It can

work with current IPv4 network structure and also support the IPv6 network structure.

With easy and friendly management interfaces and plenty of management functions

included, the industrial managed switch is the best choice for ISP to build the IPv6

FTTx edge service and for SMB to connect with IPv6 network.

Diversity for multiple applications

The industrial managed switch is a desktop size, Layer 2 / Layer 4 full managed Gigabit

switch that can handle extremely large amounts of data in a secure topology linking to

an Enterprise backbone or high capacity network server with 20 Gbps switching fabric.

The powerful features of QoS and network security provided by the industrial managed

switch provides effective data traffic control for ISPs and Enterprise VoIP, video

streaming, and multicast applications. It is ideal for the remote access layer of campus

or enterprise networks and the aggregation layer of IP metropolitan networks.

Robust layer 2 features

The industrial managed switch can be programmed for advanced switch management

functions such as dynamic port link aggregation, Q-in-Q VLAN, private VLAN, Multiple

Spanning Tree Protocol (MSTP), layer 2 to layer 4 QoS, bandwidth control, and IGMP /

MLD snooping. The industrial managed switch provides 802.1Q Tagged VLAN, and a

maximum of 255 VLAN groups are allowed. Via aggregation of supporting ports, the

industrial managed switch allows the operation of a high-speed trunk combining

multiple ports. It enables maximum up to 5 groups of 10 ports for trunk and also

supports fail-over..

Enhanced security

The industrial managed switch offers comprehensive layer 2 to layer 4 access control

list (ACL) for enforcing security to the edge. It can be used to restrict to network access

by denying packets based on source and destination IP address, TCP/UDP port

number, or defined typical network applications. Its protection mechanism also

comprises 802.1x port-based and MAC-based user and device authentication. With the

private VLAN function, communication between edge ports can be prevented to ensure

Chapter 1: Introduction

8 NS3552-8P-2S-V2 User Manual

user privacy. The industrial switches also provide DHCP snooping, IP Source Guard

and Dynamic ARP Inspection functions to prevent IP snooping from attack and discard

ARP packets with invalid MAC addresses. The network administrator can now construct

highly secured corporate networks in considerably less time and with less effort than

before.

Excellent traffic control

The industrial managed switch is loaded with powerful traffic management and QoS

features to enhance services offered by telecoms. The QoS features include wire-

speed Layer 4 traffic classifiers and bandwidth limiting that are particularly useful for

multi-tenant units, multi business units, Telco, or Network Service Provider applications.

The industrial managed switch also empowers the enterprises to take full advantage of

limited network resources and provides the best performance in VoIP and video

conferencing transmission.

Efficient and secure management

For efficient management, the industrial managed switch is equipped with console,

web, and SNMP management interfaces. With the built-in web-based management

interface, the industrial switches offers an easy-to-use, platform-independent

management and configuration facility. The industrial managed switch supports

standard Simple Network Management Protocol (SNMP) and can be managed by any

management software based on the standard SNMP v1 or v2 protocol. For text-based

management mode, the industrial managed switch can be accessed via Telnet and the

console port. Moreover, the industrial managed switch offers secure management

remotely by supporting SSH, SSL, and SNMP v3 connections where the packet content

can be encrypted at each session.

Flexible and extendable solution

The industrial managed switch features 100BASE-FX and 1000BASE-SX/LX SFP

(Small Form-factor Pluggable) fiber-optic modules, meaning the administrator now can

flexibly choose the suitable SFP transceiver according to the transmission distance or

the transmission speed required to extend the network efficiently. The distance can be

extended from 550 m to 2 km (multi-mode fiber) up to above 10/20/30/40/50/70 km

(single-mode fiber or WDM fiber). They are well suited for applications within enterprise

data centers and distributions.

Andere Handbücher für NS3552-8P-2S-V2

Inhaltsverzeichnis

Andere Interlogix Schalten Handbücher

Interlogix

Interlogix POC2502 Series Bedienungsanleitung

Interlogix

Interlogix NS3562-8P-2S Bedienungsanleitung

Interlogix

Interlogix IFS ANT-UNI-21DB-2G Bedienungsanleitung

Interlogix

Interlogix NS3562-8P-2S Bedienungsanleitung

Interlogix

Interlogix NS3702-24P-4S Bedienungsanleitung

Interlogix

Interlogix IFS NS2052-4P-1T Bedienungsanleitung

Interlogix

Interlogix IFS NS2503-8P/2C Bedienungsanleitung

Interlogix

Interlogix NS3500-24T-4C Bedienungsanleitung

Interlogix

Interlogix NS4702-24P-4S-4X Bedienungsanleitung

Interlogix

Interlogix NS3552-16P-2T-2S Bedienungsanleitung

Interlogix

Interlogix NS3552-8P-2S Bedienungsanleitung

Interlogix

Interlogix NS3500-24T-4C Bedienungsanleitung

Interlogix

Interlogix NS3500-24T-4C Montageanleitung

Interlogix

Interlogix NS3552-16P-2T-2S Bedienungsanleitung

Interlogix

Interlogix IFS NS3050-8T Bedienungsanleitung

Interlogix

Interlogix NS3503-16P-4C Bedienungsanleitung

Interlogix

Interlogix IFS ANT-OMN-15DB-2G Bedienungsanleitung

Interlogix

Interlogix NS3050-8T Bedienungsanleitung

Interlogix

Interlogix NS3553-4P-1T-2S Bedienungsanleitung

Interlogix

Interlogix NS3702-24P-4S-V2 Bedienungsanleitung

Interlogix

Interlogix IFS NS3550-24T/4S Bedienungsanleitung

Interlogix

Interlogix NS4702-24P-4X Montageanleitung

Interlogix

Interlogix NS3550-8T-2S Bedienungsanleitung

Interlogix

Interlogix MC251-4P/1S Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung