Interlogix NS3562-8P-2S Bedienungsanleitung

P/N 107322-EN • REV A • ISS 21SEP16 1

NS3562-8P-2S Industrial Wall-mount

Managed Gigabit Ethernet Switch Quick

Installation Guide

Figure 1: NS3562-8P-2S

1. Package Contents

Thank you for purchasing IFS Industrial Wall-mount

Managed Gigabit Switch, NS3562-8P-2S. The table

below shows the model with the number of ports:

Model

Name 10/100/1000T

Copper Ports

802.3at PoE

Ports 100/1000 SFP

Fiber Optical

Interface

NS3562-8P-

2S 8 8 2

In the following section, unless specified, the term “Wall-

mount Managed Switch” mentioned in this quick

installation guide refers to the NS3562-8P2S.

Open the box of the Wall-mount Managed Switch and

carefully unpack it. The box should contain the following

items:

The Wall-mount Managed Switch x 1

Quick Installation Guide x 1

3-pin Terminal Block Connector x 1

Wall-mounted Kit x 1

RJ45 Dust Cap x 8

SFP Dust Cap x2

If any item is found missing or damaged, please contact

your local reseller for replacement.

2. Requirements

Workstations running Windows

XP/2003/Vista/7/8/2008/10, MAC OS X or later,

Linux, UNIX, or other platforms are compatible with

TCP/IP protocols

Workstations are installed with Ethernet NIC

(Network Interface Card)

Ethernet Port Connection

Network cables - Use standard network (UTP)

cables with RJ45 connectors.

The above PC is installed with Web browser

and JAVA runtime environment plug-in.

Note: It is recommended to use Internet Explore 8.0 or

above to access the Wall-mount Managed Switch. If the

Web interface of the Wall-mount Managed Switch is not

accessible, please turn off the anti-virus software or

firewall and then try it again.

3. Wiring the Power Inputs

The Wall-mount Managed Switch features a strong dual

power input system (Terminal block and DC jack)

incorporated into the customer’s automation network to

enhance system reliability and uptime.

Range Model

Power Input

3-pin Terminal Block DC Jack

NS3562-8P-2S 48~56V DC 48~56V DC

2 NS3562-8P-2S Industrial Wall-mount Managed Gigabit Ethernet Switch Quick Installation Guide

Figure 2: DC Power Input

V+ = Positive / V- = Negative / Ground

3.1 Terminal Block Connector Pinout

To install the 3-pin Terminal Block Connector on the

Wall-mount Managed Switch, follow these steps:

Step 1: Insert positive DC power wire into V+, negative

DC power wire into V-, and grounding wire into

Ground.

Step 2: Tighten the wire-clamp screws for preventing the

wires from loosening and plug into the Wall-mount

Managed switch

Note:

1. The wire gauge should be in the range from 12

to 24 AWG.

2. The device must be grounded.

4. Installation

4.1 Wall Mount Installation

To install the Wall-mount Managed Switch on the wall,

follow these steps:

Step 1: There are 4 holes with 8 mm diameter on the

wall; the distance between the 2 holes is 133 mm

and the line through them must be horizontal.

Step 2: Install a conductor pipe inside the board hole

and flush the edge of the conductor pipe with the

wall surface.

Step 3: Screw the bolts into the conductor pipe. The

Wall-mount Managed Switch is between bolts and

conductor pipe, as shown below.

Figure 3: Wall Mount install

4.3 DIN-rail Mount Installation

The DIN-rail kit is included in the package. When the

wall-mount application for the Wall-mount Managed

Switch needs to be replaced with DIN-rail application,

please refer to the following figures to screw the DIN-rail

on the Wall-mount Managed Switch. To hang up the

Wall-mount Managed Switch, follow the steps below:

Step 1: Screw the DIN-rail on the Wall-mount Managed

Switch.

Figure 4: DIN Rail install

Step 2: Lightly insert the button of DIN-rail into the track.

Step 3: Check whether the DIN-rail is tightly on the

track.

NS3562-8P-2S Industrial Wall-mount Managed Gigabit Ethernet Switch Quick Installation Guide 3

5. Starting Web Management

The following shows how to start up the Web

Management of the Wall-mount Managed Switch. Note

the Wall-mount Managed Switch is configured through

an Ethernet connection. Please make sure the manager

PC must be set to the same IP subnet address.

For example, the default IP address of the Wall-mount

Managed Switch is 192.168.0.100, then the manager PC

should be set to 192.168.0.x (where x is a number

between 1 and 254, except 100) and the default subnet

mask is 255.255.255.0.

Figure 5: IP Management Diagram

Logging in to the Wall-mount Managed Switch

1. Use Internet Explorer 8.0 or above Web browser

and enter IP address http://192.168.0.100 to access

the Web interface.

2. When the following dialog box appears, please enter

“admin”in both the default user name and

password fields. The login screen in Figure 6

appears.

Default Username: admin

Default Password: admin

Figure 6: Web Login Screen

3. After entering the password, the main screen, as

shown in Figure 7.

Note: The following web screen is based on the WGS-

4215-8T2S. The display of the WGS-4215-8T2S is the

same as those of the WGS-804HPT and WGS-4215-

8T/WGS-4215-8P2S.

Figure 7: Web Main Screen of Wall-mount Managed Switch

The Switch Menu on the left of the Web page lets you

access all the commands and statistics the Wall-mount

Managed Switch provides.

Figure 8: Switch Menu

Now, you can use the Web management interface to

continue the Switch management. Please refer to the

user’s manual for more.

6. Saving Configuration via the Web

In the Wall-mount Managed Switch, the running

configuration file stores in the RAM. In the current

version, the running configuration sequence of running-

config can be saved from the RAM to FLASH by”Save

Configurations to FLASH” function, so that the running

4 NS3562-8P-2S Industrial Wall-mount Managed Gigabit Ethernet Switch Quick Installation Guide

configuration sequence becomes the startup

configuration file, which is called configuration save.

To save all applied changes and set the current

configuration as a startup configuration, the startup-

configuration file will be loaded automatically across a

system reboot.

1. Click ”Save > Save Configurations to FLASH” to

2. Press the “Apply” button to save running

configuration to start up configuration.

7. Recovering Back to Default

Configuration

IP Address has been changed or admin password

has been forgotten

To reset the IP address to the default IP address

“192.168.0.100” or reset the login password to default

value, press the reset button on the front panel for

about 5 seconds. After the device is rebooted, you can

subnet of 192.168.0.xx.

Figure 9: NS3562-8P-2S Reset Button

8. Customer Support

Thank you for purchasing IFS products. You can browse

our online FAQ resource and User’s Manual on IFS Web

site first to check if it could solve your issue. If you need

more support information, please contact IFS switch

support team.

Look under transmission products.

IFS online FAQ:

http://www.Interlogix.com/support

Switch support team mail address:

http://www.Interlogix.com/support

Interlogix is part of UTC Climate, Controls & Security, a

unit of United Technologies Corporation. All rights

reserved.

Trademarks and patents

Trade names used in this document may be trademarks

or registered trademarks of the manufacturers or

vendors of the respective products.

Andere Handbücher für NS3562-8P-2S

Inhaltsverzeichnis

Andere Interlogix Schalten Handbücher

Interlogix

Interlogix IFS ANT-PNL-9DB-2G Bedienungsanleitung

Interlogix

Interlogix IADS-PROG Bedienungsanleitung

Interlogix

Interlogix IFS ANT-OMN-15DB-2G Bedienungsanleitung

Interlogix

Interlogix NS3552-8P-2S Bedienungsanleitung

Interlogix

Interlogix NS4750-24S-4T-4X-V2 Montageanleitung

Interlogix

Interlogix NS3553-4P-1T-2S Bedienungsanleitung

Interlogix

Interlogix NS4750-24S-4T-4X Bedienungsanleitung

Interlogix

Interlogix NS3552-16P-2T-2S Bedienungsanleitung

Interlogix

Interlogix NS3500-24T-4C Bedienungsanleitung

Interlogix

Interlogix IFS NS3050-8T Bedienungsanleitung

Interlogix

Interlogix NS3050-8T Bedienungsanleitung

Interlogix

Interlogix NS3500-28T-4S Bedienungsanleitung

Interlogix

Interlogix IFS ANT-PNL-18DB-2G Bedienungsanleitung

Interlogix

Interlogix NS3562-8P-2S Bedienungsanleitung

Interlogix

Interlogix NS3500-28T-4S Bedienungsanleitung

Interlogix

Interlogix NS3500-24T-4C Montageanleitung

Interlogix

Interlogix NS3552-16P-2T-2S Bedienungsanleitung

Interlogix

Interlogix IFS NS3502-8P-2S Bedienungsanleitung

Interlogix

Interlogix NS4702-24P-4X Montageanleitung

Interlogix

Interlogix NS3702-24P-4S-V2 Bedienungsanleitung

Interlogix

Interlogix NS4750-24S-4T-4X Bedienungsanleitung

Interlogix

Interlogix NS3562-8P-2S Bedienungsanleitung

Interlogix

Interlogix IFS MC350-4T-2S Bedienungsanleitung

Interlogix

Interlogix NS3702-24P-4S Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung