Intermec EasyCoder PD4 Bedienungsanleitung

EasyCoder®PD4/PD41/PD42

Thermal Printhead (200/300 dpi) Installation Instructions

These instructions tell you how to install a 200 dpi or 300 dpi thermal

printhead in an EasyCoder PD4/PD41/PD42 printer. The kit contains the

following:

• 200 dpi or 300 dpi thermal printhead

• Printhead adapter printed circuit board (PCB)

Required Tools

To install the interface board in your printer, you need these tools:

• Screwdriver, slotted

• Screwdriver, Phillips (with magnetic tip)

Installing the Thermal Printhead and the Adapter PCB

Before you begin installation, please acknowledge the following important

safety notes:

Make sure the printer has been turned off and

disconnected from the power supply before you

start installation.

Stellen Sie sicher, dass der Drucker abgeschaltet

und von der Stromversorgung abgetrennt wurde,

bevor Sie mit der Installation beginnen.

Take precautions against electrostatic discharge, for

example, by wearing grounded wrist straps.

To install the thermal printhead

1Turn off the printer and unplug the power cord.

2Open the side door of the printer.

3Raise the printhead by pulling out the printhead lever and turning it

counterclockwise a quarter of a turn.

4Remove any thermal transfer ribbon.

5Remove the old printhead by pulling it out toward the front of the

printer.

Steps 6-9 describe how to replace the printhead adapter PCB which is

necessary if you are changing to a printhead with different resolution (for

instance, going from 200 dpi to 300 dpi). If this is not the case, go to

Step 11.

Note: If you are using a PD4 printer, you cannot switch to a

printhead with a different resolution other than that which the

printer was designed for.

6Move the balance boxes to the center position, to facilitate the removal of

the adapter PCB.

7Use an appropriate tool, for example a slotted screwdriver, to carefully

pry the printhead cable connector loose from the adapter PCB.

8Remove the two screws that attach the adapter PCB to the printer.

Remove the adapter PCB.

9Attach the new adapter PCB with the two screws removed in Step 8.

10 Connect the printhead cable to the adapter PCB.

11 Insert the new printhead and connect it to the adapter PCB.

12 Adjust the position of the balance boxes so that they fit the width of your

media.

Worldwide Headquarters

6001 36th Avenue West

Everett, Washington 98203

U.S.A.

tel 425.348.2600

fax 425.355.9551

www.intermec.com

©

2007 Intermec Technologies

Corporation. All rights reserved.

13 Close the side door of the printer.

14 Plug in the power cord and turn the printer on.

EasyCoder PD4/PD41/PD42 Thermal Printhead (200/300dpi) Installation Instructions

*1-960658-02*

P/N 1-960658-02

Andere Handbücher für EasyCoder PD4

5

Dieses Handbuch passt für folgende Modelle

2

Inhaltsverzeichnis

Andere Intermec Druckerzubehör Handbücher

Intermec

Intermec EasyCoder F2 Bedienungsanleitung

Intermec

Intermec EasyCoder 3400d Bedienungsanleitung

Intermec

Intermec PB42 Handbuch

Intermec

Intermec PB2 Series Handbuch

Intermec

Intermec 825-192-001 Bedienungsanleitung

Intermec

Intermec EasyCoder 4420 Handbuch

Intermec

Intermec EasyCoder PF8 Bedienungsanleitung

Intermec

Intermec PM4I Bedienungsanleitung

Intermec

Intermec EasyCoder PD41 Bedienungsanleitung

Intermec

Intermec UBI EasyCoder 601 E Leitfaden

Intermec

Intermec PW50 Bedienungsanleitung

Intermec

Intermec EasyCoder 501 SA Bedienungsanleitung

Intermec

Intermec EasyCoder 601XP Bedienungsanleitung

Intermec

Intermec PM4I Bedienungsanleitung

Intermec

Intermec EasyCoder 501 E Bedienungsanleitung

Intermec

Intermec EasyCoder 4420 Bedienungsanleitung

Intermec

Intermec Font Card Bedienungsanleitung

Intermec

Intermec PB50 Bedienungsanleitung

Intermec

Intermec PB42 Handbuch

Intermec

Intermec EasyCoder 501 SA Bedienungsanleitung

Intermec

Intermec EasyCoder PF4ci Bedienungsanleitung

Intermec

Intermec EasyCoder 3400e Bedienungsanleitung

Intermec

Intermec EasyCoder PF4i Bedienungsanleitung

Intermec

Intermec PC43d Bedienungsanleitung

Beliebte Druckerzubehör Handbücher anderer Marken

Star Micronics

Star Micronics TSP800 Series Bedienungsanleitung

REA

REA JET HR pro 2K Bedienungsanleitung

HP

HP Laserjet,Color Laserjet 4si Bedienungsanleitung

oliser

oliser MS 45 Bedienungsanleitung

Roland

Roland DU2-64 Anleitungen und Rezepte

Xerox

Xerox EFI EXP6000 Bedienungsanleitung

Canon

Canon Finisher-T1 Bedienungsanleitung

Sharp

Sharp FO-1MK Bedienungsanleitung

Labelmate

Labelmate PM-300 Bedienungsanleitung

Epson

Epson T6248 Betriebsanleitung

Epson

Epson OT-BZ20 Bedienungsanleitung

Canon

Canon TonerRobot EP-27 Bedienungsanleitung

Ricoh

Ricoh LCIT RT5100 Kurzanleitung

GBC

GBC 16 Series Bedienungsanleitung

Canon

Canon INNER 2-WAY TRAY-E1 Bedienungs- und Wartungshandbuch

Develop

Develop SD-509 Bedienungsanleitung

Kyocera

Kyocera KM-6230 Handbuch

Triumph Adler

Triumph Adler DF-710 Handbuch