Intermec PM4I Bedienungsanleitung

Use these installation instructions to replace the power supply unit (PSU) on

the PM4i printer. The PSU kit ships with these items:

•Power supply unit (P/N 1-971131-003)

•This installation instruction sheet

To install the power supply unit, you need:

•T20 Torx screwdriver

To install the power supply unit

1Turn off the printer power and remove the power cord.

2Lay the printer on its left cover (the electronics and front cover).

PM4i

This installation procedure must only be performed by an

authorized Intermec service technician. Intermec assumes no

responsibility for personal injury or damage to the

equipment if the installation is performed by an

unauthorized person.

The electrical components in the printer are susceptible to

damage from electrostatic discharge (ESD). You must

follow standard ESD guidelines to avoid damaging the

equipment you are servicing.

Power Supply Unit Installation Instructions

3Remove the four T20 Torx screws from the bottom of the printer and then set

the printer back upright.

4Open the media cover and remove the four T20 Torx screws that attach the

electronics and front cover to the printer.

Screw

(4 places)

Screw

(4 places)

5Lift the electronics and front cover door away from the printer and carefully

disconnect the console cable from the CPU board.

6Disconnect all of the cables from the CPU board.

7Remove the four T20 Torx screws and the standoff that attach the CPU board to

the power supply unit and lift it away from the printer.

Screw

(4 places)

Worldwide Headquarters

6001 36th Avenue West

Everett, Washington 98203

U.S.A.

tel 425.348.2600

fax 425.355.9551

www.intermec.com

© 2009 Intermec Technologies

Corporation. All rights reserved.

PM4i Power Supply Unit Installation Instructions

*931-067-001*

P/N 931-067-001

8Remove the six T20 Torx screws that attach the power supply unit to the printer,

disconnect the cables from it, and lift it away from the printer.

9To replace the power supply unit, reverse Steps 1 through 8. You need to reuse

the ground (GND) cable (P/N 236-068-003) and the cooling plate

(P/N 1-206170-00).

Note: When you remove the screws that attach the power supply unit to

the printer, the rear panel of the printer will detach.

Note: Make sure that you attach the GND cable through the lower left

screw when you replace the power supply unit.

Screw

(6 places)

Ground

cable

Andere Handbücher für PM4I

18

Dieses Handbuch passt für folgende Modelle

1

Inhaltsverzeichnis

Andere Intermec Druckerzubehör Handbücher

Intermec

Intermec ESim v4.20 Bedienungsanleitung

Intermec

Intermec EasyCoder 501 SA Bedienungsanleitung

Intermec

Intermec Font Card Bedienungsanleitung

Intermec

Intermec PB2 Series Handbuch

Intermec

Intermec EasyCoder 501XP Bedienungsanleitung

Intermec

Intermec EasyCoder F2 Bedienungsanleitung

Intermec

Intermec EasyCoder F4 Bedienungsanleitung

Intermec

Intermec EasyCoder F4 Bedienungsanleitung

Intermec

Intermec EasyCoder PF2i Bedienungsanleitung

Intermec

Intermec 4820 Kurzanleitung

Intermec

Intermec EasyCoder 3400e Bedienungsanleitung

Intermec

Intermec PA30 Bedienungsanleitung

Intermec

Intermec EasyCoder 501XP Bedienungsanleitung

Intermec

Intermec EasyCoder 3400e Bedienungsanleitung

Intermec

Intermec EasyCoder 501 SA Bedienungsanleitung

Intermec

Intermec UBI EasyCoder 601 E Leitfaden

Intermec

Intermec 074788 Series Bedienungsanleitung

Intermec

Intermec EasyCoder 101 Handbuch

Intermec

Intermec 4630 Bedienungsanleitung

Intermec

Intermec PB50 Bedienungsanleitung

Intermec

Intermec EasyCoder 501 SA Bedienungsanleitung

Intermec

Intermec PB42 Handbuch

Intermec

Intermec EasyCoder 4420 Bedienungsanleitung

Intermec

Intermec EasyCoder PF2i Bedienungsanleitung

Beliebte Druckerzubehör Handbücher anderer Marken

Star Micronics

Star Micronics TSP800 Series Bedienungsanleitung

REA

REA JET HR pro 2K Bedienungsanleitung

HP

HP Laserjet,Color Laserjet 4si Bedienungsanleitung

oliser

oliser MS 45 Bedienungsanleitung

Roland

Roland DU2-64 Anleitungen und Rezepte

Xerox

Xerox EFI EXP6000 Bedienungsanleitung

Canon

Canon Finisher-T1 Bedienungsanleitung

Sharp

Sharp FO-1MK Bedienungsanleitung

Labelmate

Labelmate PM-300 Bedienungsanleitung

Epson

Epson T6248 Betriebsanleitung

Epson

Epson OT-BZ20 Bedienungsanleitung

Canon

Canon TonerRobot EP-27 Bedienungsanleitung

Ricoh

Ricoh LCIT RT5100 Kurzanleitung

GBC

GBC 16 Series Bedienungsanleitung

Canon

Canon INNER 2-WAY TRAY-E1 Bedienungs- und Wartungshandbuch

Develop

Develop SD-509 Bedienungsanleitung

Kyocera

Kyocera KM-6230 Handbuch

Triumph Adler

Triumph Adler DF-710 Handbuch