ION Total PA Max Bedienungsanleitung

Quickstart Guide (English)

Introduction

1. Make sure all items listed in the Box Contents are included in the box. Look in the box under the

foam sheet for the speaker stand rubber feet, speaker stand mounting knob, power cable, and

microphone.

2. Read the safety instruction booklet before using the product.

3. Study the Connection Diagram.

4. Make sure all input devices such as microphones, CD players, or digital media players are turned

off and volume settings are set at “zero.”

5. Connect all devices as shown.

6. Switch everything on in the following order:

•audio input sources (i.e. microphones, instruments, CD players)

•Total PA Max

7. When turning off, always reverse this operation:

•Total PA Max

•any input devices

Box Contents

Total PA Max

Microphone with Cable

Telescoping Speaker Stand

Remote Control

Power Cable (IEC)

Quickstart Guide

Safety Instructions & Warranty Information Booklet

Support

For the latest information about this product (system requirements, compatibility information, etc.)

and product registration, visit ionaudio.com.

For additional product support, visit ionaudio.com/support.

Caution: Do not expose Total PA Max to rain or standing water.

Quick Setup

Connection Diagram

Speaker Stand Installation

1. Fully extend the speaker stand tripod legs on a flat, stable

surface. Look in the box contents under the foam sheet for the

rubber feet and speaker stand mounting knob.

2. Raise the mounting pole up to the appropriate height needed

and tighten the side adjustment knob.

3. Insert the pin into the bottom pin-hole so the mounting pole

stays at your set height.

4. On Total PA Max, adjust the bottom knob counter-clockwise

so the screw is not blocking the opening.

5. Line up the Total PA Max mounting hole with the speaker stand

pole and place on the pole.

6. Tighten the mounting knob clockwise on Total PA Max.

3 45/6

Items not listed under

Introduction > Box Contents

are sold separately.

Tablet

Microphones

SD Card

USB drive

Smartphone

Power

Features

Rear Panel

1. Media Panel: Controls for the USB, SD, FM radio (if

applicable), and Bluetooth sources. The Media Panel

Mode source symbol will illuminate when that source

is playing.

2. USB Port: Connect your USB flash drive here to play

music.

3. SD Card Slot: Insert your SD card here to play music.

4. Display: Displays the media panel modes for USB,

SD, FM radio (if applicable), and Bluetooth.

Note: The display comes with a plastic protector on it.

Remove this for optimal viewing.

5. Mic Inputs (1/4”/6.35 mm & XLR):Connect a dynamic

microphone to the 1/4” (6.35 mm) or XLR inputs.

Control the volume of the inputs using the Mic Input

Volume knobs.

6. Mic Input Volume: Turn this knob to adjust the input

volume of the Mic Input.

7. Aux Input (1/8”/3.5 mm):Connect a CD player, digital

media player, or other audio source to this 1/8” (3.5

mm) stereo auxiliary input. Control the volume using

the Aux Input Volume knob.

8. XLR Input (XLR):Connect a line-level mixer or musical

instrument to this XLR line-level input. Control the

volume using the Aux Input Volume knob. Use this line-

level input when linking together two Total PA Max

units.

9. RCA Inputs: Connect a CD player, digital media

player, mixer, or other media source to these inputs.

Control the volume using the Aux Input Volume knob.

10. Aux Input Volume: Turn this knob to adjust the input

volume of the Aux Input, XLR Input, and RCA Inputs.

11. Mix Out (XLR):Connect this XLR output to another

active (powered) speaker. The level of the output is

controlled by the Mic Input Volume, Aux Input

Volume, and Master Volume.

12. Mic Echo: Use this knob to add or remove an echo effect to the Mic Inputs.

13. High EQ: Increases or decreases the high (treble) frequencies for Mic Input, Line Input, and

Media Panel sources at a range between -12 dB to +12 dB.

14. Low EQ: Increases or decreases the low (bass) frequencies for Mic Input, Line Input, and

Media Panel sources at a range between -12 dB to +12 dB.

15. Master Volume: Turn this knob to adjust the overall output volume of the loudspeaker.

16. Clip LED: This LED will flash red if the signal from the inputs or media panel source is clipping. If

this happens, decrease the setting of the Mic Input Volume knob, Aux Input Volume knob, or

Master Volume knob.

17. Power LED: Indicates whether Total PA Max is powered on or off.

18. Light Mode Button: Press this button to select how the lights on the front panel function:

•Color Cycle: The lights slowly glow and cycle through colors. Press and hold the light mode

button to freeze the lights on one color. This is the default mode when Total PA Max is first

powered on.

•Beat Sync: The lights react to the beat of the music.

•Off: The lights turn off.

19. Power Cable Input (IEC):Insert the included power cable here to power the unit.

20. Fuse: The orientation of the fuse holder determines the current voltage setting

of Total PA Max. The current setting is shown above the white triangle ():

110–120 V or 220–240 V. If you use Total PA Max in a region with a different

voltage, change the voltage setting by removing the fuse holder, inverting it,

and reinserting it.

If the unit’s fuse is broken, remove the fuse holder and replace the broken fuse

with one with the same rating (printed on the fuse holder). Using a fuse with an

incorrect rating can damage the unit and/or fuse.

21. Power Switch: Turns Total PA Max on or off.

Media Panel

Media Panel Functions:

MODE Mode: Switches modes from USB, SD, FM radio (if applicable), or Bluetooth.

Play/Pause: Play/pause the USB, SD, or Bluetooth source. Press and hold Play/Pause for 2

seconds to begin the preset auto-store function (if applicable). This jumps to the lowest

station (87.5) and then travels through the bandwidth to auto-store the strongest stations as

presets.

Repeat: Repeat all of the tracks (ALL), repeat all of the tracks in the folder (FOLd), repeat the

current playing USB or SD track (OnE), or shuffle the track order (rAn).

Previous: Plays the previous USB, SD, or Bluetooth track. When listening to the FM radio (if

applicable), press the button once to skip back through the FM stations and hold the button

down to seek back through the channel presets.

Next: Plays the next USB, SD, or Bluetooth track. When listening to the FM radio (if

applicable), press the button once to tune the radio down one preset and hold the button

down to seek forward through the channel presets.

Note: In some apps, pressing the Previous ( ) or Next ( ) buttons may go to another playlist or

music genre.

Media Panel Remote

Note: Aim the remote straight at the front of the speaker woofer. Room lighting and battery life can

affect the operating range of the remote control.

Note: In order to use the remote control for the first time, first pull out the tab attached to the battery

compartment. To change the remote battery, follow the diagram located on the back of the remote.

Use a 3 V DC CR2032 lithium button cell battery for replacement.

1. Stop: Stops the media panel source from playing.

2. Mode: Selects the media panel source: USB, SD, FM radio (if applicable),

or Bluetooth.

3. Mute: Silences the music playback on media panel sources.

4. Prev ( ): Goes to the previous USB or SD card track. When listening to

Bluetooth sources, pressing Prev in some apps may go to another playlist

or music genre. When listening to the FM radio (if applicable), press the

Prev button once to skip back through the FM stations and hold the button

down to seek back through the channel presets.

5. Next ( ): Advances to the next USB or SD card track. When listening to

Bluetooth sources, pressing Next in some apps may go to another playlist

or music genre. When listening to the FM radio (if applicable), press the

Next button once to tune the radio down one preset and hold the button

down to seek forward through the channel presets.

6. Play/Pause (): Plays or pauses the USB, SD, or Bluetooth media panel source. Press and hold

Play/Pause for 2 seconds to begin the preset auto-store function (if applicable). This jumps to

the lowest station (87.5) and then travels through the FM band to auto-store the strongest

stations as presets.

Note: Files are played from the USB or SD source first by alphabetical order of what is on the

root level, then alphabetical by folder, and then alphabetical by the track name.

7. Vol –: Decreases the media panel source volume.

8. Vol +: Increases the media panel source volume.

Note: The remote volume only affects the media panel source and works together with the

physical media panel volume knob on the unit’s rear panel.

9. EQ: Selects one of the following digital EQ presets to use with a media panel source: Bass (BAS),

Pop (POP), Rock (rOC), Jazz (JA2), Classical (CLA), Country (COU), No EQ (OFF, factory default

setting).

Note: The digital EQ only works for Bluetooth, USB flash drive, and SD card sources.

10. 100+: Jumps ahead by 100 tracks.

11. 200+: Jumps ahead by 200 tracks.

12. Number Keys: Provides channel selection for FM radio stations (if applicable), and track

selection for USB and SD card sources.

Operation

Pairing a Bluetooth Device

1. Turn on your Bluetooth device.

2. Power on Total PA Max.

3. Use the Mode button to select Bluetooth mode, which appears as "bt" in the display. Total PA

Max will automatically go into pairing mode to search for Bluetooth devices. You will know you

are in pairing mode when the Bluetooth icon is flashing.

4. Navigate to your Bluetooth device’s setup screen, find Total PA Max, and connect. The

Bluetooth icon will remain solidly lit.

Note: Users should consider updating their device’s OS if experiencing trouble with pairing or

playing music.

5. To disconnect pairing, turn off Bluetooth on your device or select Forget this device from your

device.

Pairing a Bluetooth Device Using NFC

NFC (near-field communication) allows data exchange from devices, such as pairing, by gently

bumping them together. Check in your device’s manual to see if this feature is supported.

To use NFC to pair with Total PA Max:

1. In order to use NFC, your device must be turned on and unlocked.

2. Enter your device’s Settings menu and check that NFC is turned On (one-time step).

3. Power on Total PA Max.

4. Touch and briefly hold your device to the NFC logo located on Total PA Max’s rear panel.

5. Follow the pairing instructions that appear on your phone. If a passcode is required, enter

“0000”.

6. To unpair, gently bump your device against the NFC logo.

Troubleshooting

If the sound is distorted: Try lowering the volume control of your sound source or musical

instrument. Also, try to reduce the overall volume of Total PA Max.

If there is too much bass: Try adjusting the tone or EQ control from Total PA Max or your sound source

to lower the bass level. This will allow you to play the music louder before clipping (distortion) occurs.

If there is a high-pitched whistling noise when using a microphone: This is probably feedback.

Point the microphone away from the speaker.

If you can’t hear the microphone over the music volume: Turn down the music volume from your

source.

When I press Previous ()or Next ( ), it doesn’t increment to the next FM station: Short

presses of the button will jump to presets. Hold the button down to seek to the next station. (If

applicable)

If the radio station channel is flashing: The unit is currently muted. Unmute to stop the flashing

and resume playback.

If the Bluetooth logo is flashing rapidly: The unit is currently in pairing mode.

If the Bluetooth logo is flashing slowly: A device is paired, but the music is muted. Unmute to stop

the flashing and resume playback.

The USB track number (Example: 001)is flashing slowly: The USB drive music playback is muted.

Unmute to stop the flashing and resume playback.

The LCD shows “NONE”:The unit is in USB/SD mode, but there is no USB drive attached or no SD

card inserted.

Andere Handbücher für Total PA Max

Inhaltsverzeichnis

Andere ION Sprecher Handbücher

ION

ION Party Rocker Go Bedienungsanleitung

ION

ION Bright Max Bedienungsanleitung

ION

ION Solar Stone Multi Bedienungsanleitung

ION

ION Sound Stone 2 Bedienungsanleitung

ION

ION EXPLORER IPA76S Bedienungsanleitung

ION

ION Block Rocker Series Gebrauchs- und Pflegehandbuch

ION

ION Pathfinder 280 Bedienungsanleitung

ION

ION Game Day Lights Bedienungsanleitung

ION

ION Pathfinder 280 Bedienungsanleitung

ION

ION Solar Stone Glow Bedienungsanleitung

ION

ION TOTAL PA GLOW Bedienungsanleitung

ION

ION Party Rocker Plus Bedienungsanleitung

ION

ION Party On Bedienungsanleitung

ION

ION BLOCK ROCKER FLASH Bedienungsanleitung

ION

ION PATHFINDER GO Bedienungsanleitung

ION

ION BLOCK ROCKER BLUETOOTH Bedienungsanleitung

ION

ION PRO GLOW ULTRA Bedienungsanleitung

ION

ION Road Rider Bedienungsanleitung

ION

ION Job Rocker Max Bedienungsanleitung

ION

ION Solar Stone Multi Bedienungsanleitung

ION

ION Luxe LP Bedienungsanleitung

ION

ION Dunk Bedienungsanleitung

ION

ION Tailgater Plus Bedienungsanleitung

ION

ION Block Party Ultra Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung