Ipevo IW2S Bedienungsanleitung

Quick Start Guide

for IW2S Wireless Interactive Whiteboard System

Short Throw Version

The Basics

The IPEVO Wireless Interactive Whiteboard System Short Throw

Version, or IW2S, is a compact 3-piece system that turns your large

projection screen into an interactive touchscreen. It is specially

designed to use with ceiling-mounted short-throw projectors. Once

set up, you can use it to control your computer’s cursor. And if you

have any annotation software installed on your computer, you can also

use IW2S to draw/annotate on your projection screen.

Emits infrared signals on

contact or by pressing the

green button.

INTERACTIVE PEN

Reads infrared signals from

the Interactive Pen and

translates them into cursor

movements and mouse

button presses.

SENSOR CAM

Plugged into an open USB

port, it allows the Sensor Cam

to communicate wirelessly

with your computer.

WIRELESS RECEIVER

Getting to Know IW2S

LED Indicator

Lights up when powered up and connected. Different colors

(solid and blinking) reflect different states.

Sensor Power Button

Press to turn on Sensor Cam and enter Active Mode. Press

again to enter Sleep Mode.

Lens

Detects signals emitted by the Interactive Pen.

Hinged Metal Base

Allows adjustment of the angle

of the Lens.

Micro-USB Port

Connect included Micro-USB cable here.

Pairing Button

Press for 3 seconds to enter Pairing Mode.

By default, no pairing action is required – the Sensor Cam and

Wireless Receiver you received are already paired. However, if you

are using a replacement Wireless Receiver or Sensor Cam, you’ll

need to pair them before use. For the pairing instructions, please

refer to the FAQ section at www.ipevo.com/iw2s.

Green

Color State

The Sensor Cam is powered on and connected

with the Wireless Receiver.

The Sensor Cam is not connected with the

Wireless Receiver. Check that the Wireless

Receiver is plugged into your computer and

placed within 16 ft (5m) of the Sensor Cam.

Blinking

Orange

Red The Sensor Cam is in Sleep Mode.

Contact Sensitive Tip

Tap for a left click, or tap

and hold for 2s or longer

for a right click. Quickly tap

twice for a double-click.

IPEVO Button

Press for a left click, or

press and hold for 2s or

longer for a right click.

Press twice for a dou-

ble-click.

Wrist Strap Attachment

Holes

Attach the included wrist

strap here.

Wireless Receiver

Plug it into your computer

for a wireless connection

between your computer and

the Sensor Cam.

Battery Cover

Open to reveal slots for 2

AAA batteries.

Power Switch

Turn the Interactive Pen

on or off.

Sensor Power Button

Remotely turn your Sensor

Cam on or off.

1. Software Installation

IW2S requires IW Driver to function. IW Driver allows you to calibrate

and control your IW2S. Please visit IPEVO website at support.ipevo.

com/iw2s to download it.

Installing IW2S

Remove the battery cover from the Interactive Pen and insert 2 AAA

batteries. Replace the cover. Attach the included wrist strap into the

attachment holes. Turn on the pen when ready to use.

2. Readying the Interactive Pen

Turn on

3. Connecting Sensor Cam to Computer

To connect the Sensor Cam wirelessly to your computer, please follow

the steps below:

1. Connect the Sensor Cam to a power outlet by plugging the Micro-USB

cable into the Micro-USB port on the Sensor Cam, then plugging the

other end of the cable into the included power adapter. Lastly, plug

the power adapter into an outlet.

Note: DO NOT turn on the Sensor Cam during this step.

Sensor Power Button

Power Adapter

3. Turn on the Sensor Cam by pressing the Sensor Power Button

located on the Interactive Pen. Next, check the LED indicator of the

Sensor Cam. It will light up Green once it is successfully connected to

your computer.

Green Light

Press the

Sensor Power Button

2. Detach the Wireless Receiver from the bottom of the Interactive Pen

and plug it into the USB port of your computer.

4. Positioning the Sensor Cam

The optimum position for the Sensor Cam will be the same location

as your ceiling-mounted short-throw projector. However, depending

on the make and model of your projector, and even your screen size,

there might be some exceptions. Please refer to the following chart for

a general guideline:

Screen Size 50” 60” 70” 80” 90”~100”

Minimal

Distance

1.6 ft

(50 cm)

2.0 ft

(60 cm)

2.3 ft

(70 cm)

2.6 ft

(80 cm)

3.0~4.0 ft

(90~120cm)

For maximum accuracy, the Sensor Cam MUST be positioned and

firmly affixed on your ceiling-mounted short-throw projector. Before

affixing the Sensor Cam, please hold the Sensor Cam in an area just

below (by a few inches) the projector and run the calibration

process once to make sure the Sensor Cam can indeed cover your

whole projection screen.

5. Securing the Sensor Cam

Installing IW2S (cont’d)

After that, you can affix the Sensor Cam directly to the projector using

the included ceiling mount by following the steps below:

1 2 Remove the sticker

6. Calibration

IW2S must be calibrated before it can be used. To start the process,

please click on the IW Driver icon located in the task bar or status

bar and choose “Calibrate”. To complete the process, please follow

the onscreen instructions carefully. Your IW2S is ready for use once

calibration has been completed.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

FCC Caution: Any changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause

undesired operation.

This device and its antenna(s) must not be co-located or operating in conjunction with any other

antenna or transmitter.

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/ TV technician for help.

owned by IPEVO Inc. and may be registered. All other trademarks are the property of their respective owners.

Customer Service

Email: cs@ipevo.com

Tel: 1 (408) 490 – 3085

Inhaltsverzeichnis

Andere Ipevo Whiteboard Handbücher

Ipevo

Ipevo IS-01 Bedienungsanleitung

Beliebte Whiteboard Handbücher anderer Marken

Copernicus

Copernicus RC105 Bedienungsanleitung

IKEA

IKEA MALA 104.889.67 Bedienungsanleitung

SMART

SMART SBX800 Bedienungsanleitung

SMART

SMART Board MX V3 Series Bedienungsanleitung

funtronic

funtronic EasyBoard Bedienungsanleitung

Best-Rite

Best-Rite Baby Folding Wheasel 784-T Bedienungsanleitung

Best-Rite

Best-Rite Modular Room Divider Bedienungsanleitung

IKEA

IKEA MALA 504.565.92 Bedienungsanleitung

Panasonic

Panasonic TX-47P800HQ TX-47P800HZ Bedienungsanleitung

SMART

SMART ST442i Bedienungsanleitung

Quartet

Quartet QRT-72981 Bedienungsanleitung

SMART

SMART Smart Board 480 Bedienungsanleitung

EGAN

EGAN GlassWrite TableScreen TSG Bedienungsanleitung

Claridge

Claridge Edify Mobile Bedienungsanleitung

Legamaster

Legamaster e-Board Touch 2 Bedienungsanleitung

Nureva

Nureva WALL Bedienungsanleitung

Best-Rite

Best-Rite Black Splash Bedienungsanleitung

Da-Lite

Da-Lite Cosmopolitan Electrol Bedienungsanleitung