IRobot E5 Series Bedienungsanleitung

This is the safety alert symbol. It is used to alert you to potential physical injury hazards.

Obey all safety messages that follow this symbol to avoid possible injury or death.

WARNING: When using an electrical appliance, basic precautions should always be followed,

including the following:

WARNING: To reduce the risk of injury or damage, read and follow the safety precautions when

setting up, using, and maintaining your robot.

This appliance may only be used by children aged 8 years and above and persons with

reduced physical, sensory, or mental capabilities or lack of experience and knowledge if they

have been given supervision or instruction concerning use of the appliance in a safe way and

understand the hazards involved. Children must not play with the appliance. Cleaning and user

maintenance must not be carried out by children without supervision.

Safety Information

Important Safety Information

READ ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

Risk of electric shock Class II equipment Read owner’s

manual

Risk of ﬁre For indoor use only Keep out of reach

of children

Backfeed Protection

General symbol for

recycling

Indicates output

polarity

Rated power

input, d.c.

Rated power

output, d.c.

Separate Supply Unit Rated power

input, a.c.

BFP

CAUTION

• Be aware that the robot moves on its own. Take care when

walking in the area that the robot is operating in to avoid

stepping on it.

• Do not operate the robot in areas with exposed electrical

outlets in the ﬂoor.

• Do not use this device to pick up sharp objects, glass, or

anything that is burning or smoking.

• If the device passes over a power cord and drags it, there

is a chance an object could be pulled o a table or shelf.

Before using this device, pick up objects like clothing, loose

papers, pull cords for blinds or curtains, power cords, and

any fragile objects.

NOTICE

• This robot is intended for dry ﬂoor use only. Do not use this

device to pick up spills. Do not allow your robot or Home Base

charging station to become wet.

• Do not place anything on top of your robot.

• The failure to maintain the cleanliness of charger contacts

could result in loss of ability for the robot to charge the battery.

HOME BASE™ CHARGING STATION

WARNING

• Do not use a Home Base with a damaged cord or plug. If the

cord or plug is damaged, it must be replaced.

• Always disconnect your robot from the Home Base before

cleaning or maintaining it.

GENERAL

WARNING

• Your robot is not a toy. Small children and pets should be

supervised when your robot is operating.

• Do not sit or stand on your robot or Home Base charging station.

• Do not use unauthorised chargers. Use of an unauthorised

charger could cause the battery to generate heat, smoke, catch

ﬁre, or explode.

• Your robot comes with a region approved power supply cord

and is designed to be plugged into a standard household AC

power outlet only. Do not use any other power supply cord. For

replacement cords, please contact Customer Care to ensure

proper selection of country speciﬁc power supply cord.

• Do not open your robot or the Home Base charging station.

There are no user serviceable parts inside. Refer servicing to

qualiﬁed service personnel.

• Risk of electric shock, use indoors in dry locations only.

• Do not handle your robot and Home Base with wet hands.

• Store and operate your robot in room temperature

environments only.

• If the room to be cleaned contains a balcony, a physical

barrier should be used to prevent access to the balcony

and ensure safe operation.

WARNING: Indicates a hazardous situation that, if not avoided, could

result in death or serious injury.

CAUTION: Indicates a hazardous situation that, if not avoided, could

result in minor or moderate injury.

NOTICE:

Indicates a hazardous situation that, if not avoided, could

result in property damage.

contact has been made, wash the aected area with copious

amounts of water and seek medical advice. Place the battery

in a sealed plastic bag and dispose of it safely according

to local environmental regulations. Return it to your local

authorised iRobot Service Centre for disposal.

• Lithium ion batteries and products that contain lithium ion

batteries are subject to stringent transportation regulations.

If you need to ship this product (with the battery included)

for service, travel, or any other reason, you MUST see the

Troubleshooting section of your manual or contact Customer

Care for shipping instructions.

CAUTION

• Battery usage by children should be supervised. Seek medical

advice immediately if a cell or battery has been swallowed.

NOTICE

• The battery pack must be removed from the robot before

disposal.

• For best results, only use the iRobot lithium ion battery that

comes with the robot.

• Do not use non-rechargeable batteries. Use only the

rechargeable battery supplied with the product. For

replacement, purchase an identical iRobot battery or contact

iRobot Customer Care for alternative battery options.

• Batteries must be disposed of in accordance with local

regulations.

• Always charge and remove the battery from your robot and

accessories before long-term storage.

• Only use the included battery charger to charge the iRobot

ABL-D1 battery. Other types of batteries may burst, causing injury.

Always contact Customer Care for the correct replacement of

your battery. Battery Charger model 17070: Input AC 100-240 V,

50-60 Hz, 0.68 A; 33 W. Output DC 20.5 V, 1.25 A.

• To prevent the risk of your robot falling down stairs, ensure that

the Home Base Charging Station is placed at least 4 feet (1.2

metres) away from stairs.

NOTICE

• The product may not be used with any type of power converter.

Use of power converters will immediately void the warranty.

• If you live in an area prone to electrical storms, it is recommended

that you use additional surge protection. Your robot’s Home Base

may be protected with a surge protector in the event of severe

electrical storms.

BATTERY

WARNING

• Do not open, crush, heat above 176° F: 80° C, or incinerate.

Follow manufacturer’s instructions.

• Do not short-circuit the battery by allowing metal objects to

come into contact with the battery terminals, or immerse in liquid.

Do not subject batteries to mechanical shock.

• Periodically inspect the battery pack for any sign of damage

or leakage. Immediately stop using the battery if there are

noticeable abnormalities, such as smell, heat, discolouration, or

deformity. Do not charge damaged or leaking battery packs;

do not allow the liquid to come into contact with skin or eyes. If

1 For more information, visit global.irobot.com

Bottom View

Top View

Light Touch

Sensor

Faceplate

Dust Bin

and Filter

Handle

Charging

Contacts

RCON

Sensor

IR Sensor

Window

RCON Sensor

Charging

Contacts

Castor Wheel

Cli Sensor

Edge-Sweeping

Brush

Multi-Surface

Brushes

Cli Sensor

Brush Frame

Release Tab

Brush Caps

Dust Bin and Filter

Home Base

Buttons & Indicators

Home Button

CLEAN/Power Button

Troubleshooting

Indicator

Battery Indicator

Spot Clean Button

Wi-Fi Indicator

About your Roomba® Robot Vacuum

Bin Release

Button

Roomba®e5 Owner’s Guide 2

Using Your Roomba®Robot Vacuum

Note: Your robot comes with a partial charge, but we recommend that you

charge the robot on the Home Base for 3 hours prior to starting the ﬁrst

complete cleaning cycle.

Note: Remove excess clutter from ﬂoors before cleaning (e.g. clothing, toys, etc.).

Use your Roomba®robot vacuum frequently to maintain well-conditioned ﬂoors.

If the robot is returning to recharge after completing a cleaning cycle,

itwill play a series of tones to indicate successful completion of the job.

• To pause the robot during a cleaning cycle, press CLEAN.

• To resume the cleaning cycle, press CLEAN again.

• To send the robot back to its Home Base during a cleaning cycle, press

CLEAN and then (Home) button on the robot or press CLEAN on the

iRobot HOME App main screen. This will end the cleaning cycle.

Note: When the robot is returning to the Home Base, the (Home) button

willblink.

• The robot will automatically engage Dirt Detect™ mode when it

encounters a high concentration of dirt or debris. The robot will move

in a spiral motion to clean the area more thoroughly. The CLEAN

button will pulse when the robot engages Dirt Detect™ mode. When

ﬁnished, the robot will continue its cleaning job.

Set up the Home Base™ charging station

WARNING: To prevent the risk of your robot falling down stairs, ensure that

the Home Base Charging Station is placed at least 4 feet (1.2 metres) away

from stairs.

Place the Home Base in an open, uncluttered area, leaving the

following distances around the Home Base:

• At least 1.5 feet (0.5 metres) on each side of the Home Base

• At least 4 feet (1.2 metres) in front of the Home Base and at least

4feet (1.2 metres) away from stairs

• At least 8 feet (2.5 metres) from Virtual Wall Barriers

• Always keep the Home Base plugged in and make sure it is in an area

with consistent Wi-Fi®coverage to allow the Roomba®robot vacuum

to receive information via the iRobot HOME App.

Download the iRobot HOME App and connect to Wi-Fi ®

• Watch an overview video with instructions on how to set up and use

your Roomba®robot vacuum

• Set an automatic cleaning schedule and customise cleaning

preferences

• Enable automatic software updates

• Access tips, tricks, and answers to commonly asked questions

including how to pair your Roomba®robot vacuum with other smart

devices.

Get to know your robot

• Place the robot on the Home Base to activate the battery

3 For more information, visit global.irobot.com

Dual Mode Virtual Wall®Barrier

(compatible with all models)

Use the Dual Mode Virtual Wall®barrier

to keep the robot in the places you want

cleaned – and out of the ones you don’t.

It creates an invisible barrier that only the

robot can see. You can leave the device

in position between cleanings.

Choose the mode to meet your needs:

Virtual Wall Mode: When the switch

is in the Virtual Wall position ( ), the

device will create a linear barrier to block

openings up to 10 feet (3 metres).

Note: This barrier gets wider as it gets

further from the device (refer to illustration).

Accessories

10 ft./3 m

24 in/60 cm

Halo Mode: Toggle the switch to the

Halo position ( ) to create a circular

barrier. This will prevent the robot

from approaching zones you want

to protect such as a pet bowl, vase,

or under a desk. The Halo barrier

extends approximately 24 inches (60

centimetres) from the centre of the

device.

• You can use the Spot Clean feature to make the robot target

speciﬁc spills. Just place the robot in the centre of the debris and

press (Spot Clean). The robot will clean the area by spiralling

outwards about 3 feet (1 metre) and then spiral inwards to end

where it started.

• Keep the robot on the Home Base™ charging station so it’s always

ready to clean when you need it. If you need to store the robot o

the charging station, turn o the battery by removing the robot

from the Home Base charging station and holding down the

(Home) button for 9 seconds. All indicators will turn o and you

will hear an audible tone. You can then store the robot in a cool,

dry place. To wake the robot up and turn on the battery, plug

in the Home Base charging station and place the robot on the

charging station.

• When the robot is charging, it will turn o the indicator lights

to save energy. You can check the status by pressing the

CLEAN button. The Battery Indicator icon will illuminate amber

when the battery is charging and green when the battery is fully

charged. Battery charge status can also be viewed in the

iRobot HOME App.

Note: After each use, empty the bin and clean the ﬁlter.

Note: The batteries will last about 8-10 months under normal use. If you are not

planning to use your Virtual Wall barrier for an extended period of time, be sure

to turn the switch to the O or middle position.

Roomba®e5 Owner’s Guide 4

Care and Maintenance Instructions

To keep your Roomba®robot vacuum running at peak

performance, perform the procedures on the following

pages.

There are additional instructional videos in the iRobot HOME

App. If you notice the robot picking up less debris from your

ﬂoor, empty the bin, clean the ﬁlter, and clean the brushes.

Care and Maintenance Overview

Care and Maintenance

Note: iRobot manufactures various replacement parts and

assemblies. If you think you need a replacement part, please

contact iRobot Customer Care for more information. Ask

Customer Care or visit an authorised iRobot®dealer.

*Replacement frequency may vary. Parts should be replaced

ifvisible wear appears.

Emptying the Bin

Open the bin door to empty the bin.

Press the bin release

button to remove the bin.

Place the bin back into the robot.

Cleaning the Filter

Release the bin. Remove the

ﬁlter by grasping both ends

and pulling out.

Shake o debris by tapping

the ﬁlter against your

household rubbish bin.

Reinsert the ﬁlter with the

ridged grips facing out.

Place the bin back into

the robot.

Important: The robot will not

run if the ﬁlter is not installed

correctly. Replace the ﬁlter

everytwo months.

Part Care Replace* Details

Bin Empty after each use Page 3

Filter Clean every week

(twice a week if you

have a pet)

Every 2

months

Page 3

Front Castor

Wheel

Clean every 2 weeks Every 12

months

Page 4

Edge-

Sweeping

Brush and

Multi-Surface

Brushes

Clean every month

(twice a month if you

have a pet)

Every 12

months

Page

4-5

Sensors and

Charging

Contacts

Clean once a month Page 5

5 For more information, visit global.irobot.com

Washing the Bin

Rinse the bin using warm water.

Make sure that the bin is completely

dry. Reinsert the ﬁlter and place the

bin back into the robot.

Important: Do not wash the ﬁlter.

Remove the ﬁlter before washing the bin.

Release the bin, remove the

ﬁlter, and open the bin door.

Note: The bin is not dishwasher safe.

Cleaning the Front Castor Wheel

Pull ﬁrmly on the front wheel to remove it.

Remove any debris from inside the

wheelcavity.

Reinstall all parts when ﬁnished. Make

sure the wheel clicks back into place.

Use a coin or small screwdriver to remove

the screw holding the Edge-Sweeping

Brush in place.

Remove the Edge-Sweeping Brush, clean

the brush and the brush post, and then

reinstall the brush.

Important: A front wheel clogged with

hair and debris could result in damage to

your ﬂoor. If the wheel is not spinning freely

after you have cleaned it, please contact

Customer Care.

Cleaning the Edge-Sweeping Brush

Wheel

Axle

Housing

Roomba®e5 Owner’s Guide 6

Pinch the brush frame release

tab, lift the tab, and remove any

obstructions.

Remove the brushes from the

robot. Remove the brush caps

from the ends of the brushes.

Remove any hair or debris that

has collected beneath the

caps. Reinstall the brush caps.

Cleaning the Multi-Surface Brushes

Remove any hair or debris from

the square and hexagonal pegs

on the opposite side of the

brushes.

Remove the bin from the robot

andclear any debris from the

vacuumpath.

Reinstall the brushes in the robot.

Match the shape of the brush pegs

with the shape of the brush icons in

the cleaning head module.

Cleaning the Sensors and Charging

Contacts

Wipe sensors and charging contacts with

aclean,dry cloth.

Important: Do not

spray cleaning

solution or water

onto the sensors or

sensor openings.

7 For more information, visit global.irobot.com

Troubleshooting

Your Roomba®robot vacuum will tell you something is wrong with a two-

tone alert, a spoken message, and a blinking troubleshooting indicator

( ). Follow the audible instructions. More detailed support and videos

are available in the iRobot HOME App and at global.irobot.com.

To reboot your robot, press and hold the (Home) and (Spot Clean)

buttons for 10 seconds until all indicators turn o, then release. When

you release the buttons, you will hear a tone to conﬁrm a successful

reboot.

Note: If you use the scheduling feature, open the iRobot HOME App after

rebooting to conﬁrm that the robot’s schedule remains intact.

Reduced Power Standby Mode

The Roomba®robot vacuum uses a small amount of power whenever

it is on the Home Base™ charging station. This ensures that the

robot is always ready for the next cleaning job and maintains Wi-Fi®

connectivity. You can put the robot in a further-reduced power state

when not in use. For instructions and more details on this Reduced

Power Standby Mode, refer to the iRobot HOME App.

Lithium Ion Battery

For best results, only use the iRobot lithium ion battery that comes with

your Roomba®robot vacuum.

WARNING: Lithium ion batteries and products that contain lithium ion

batteries are subject to stringent transportation regulations. If you need to

ship this product (with the battery included) for service, travel, or any other

reason, you MUST follow the shipping instructions below.

• The battery MUST be turned o before shipping.

• Remove the robot from the Home Base Charging Station.

• Ensure that the CLEAN button is illuminated by pressing the CLEAN

button once quickly.

• Once the button is illuminated, press and hold the CLEAN button for

12seconds. You will hear an audible tone.

• Once you hear the tone, release the CLEAN button. The battery is now

turned o.

• Package the product in its original packaging.

• Ship via ground transportation only (no air shipping).

• If you need further assistance, contact our Customer Care team.

Inhaltsverzeichnis

Andere iRobot Staubsauger Handbücher

iRobot

iRobot Roomba 4210 Bedienungsanleitung

iRobot

iRobot Roomba Bedienungsanleitung

iRobot

iRobot Vacuum Cleaning Robot Bedienungsanleitung

iRobot

iRobot Roomba i6 Bedienungsanleitung

iRobot

iRobot Roomba 4110 Bedienungsanleitung

iRobot

iRobot H1 Bedienungsanleitung

iRobot

iRobot 120 Bedienungsanleitung

iRobot

iRobot ROOMBA 900 SERIES Betriebsanleitung

iRobot

iRobot Roomba Discovery 4 Series Bedienungsanleitung

iRobot

iRobot Roomba 600 Series Bedienungsanleitung

iRobot

iRobot Roomba Combo j9+ Bedienungsanleitung

iRobot

iRobot Roomba i7 Bedienungsanleitung

iRobot

iRobot RVE-Y2 Originalbetriebsanleitung

iRobot

iRobot Roomba 4110 Bedienungsanleitung

iRobot

iRobot Roomba 600 Series Bedienungsanleitung

iRobot

iRobot Roomba Professional Series Bedienungsanleitung

iRobot

iRobot Roomba Bedienungsanleitung

iRobot

iRobot Roomba Bedienungsanleitung

iRobot

iRobot Looj Bedienungsanleitung

iRobot

iRobot Scooba 200 Series Bedienungsanleitung

iRobot

iRobot Roomba 4105 Bedienungsanleitung

iRobot

iRobot R11384 Bedienungsanleitung

iRobot

iRobot Roomba j7 Bedienungsanleitung

iRobot

iRobot H1 Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

Exido

Exido 240-114 Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung

iRobot e5 Series Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken