Ivoclar Vivadent Programat CS4 Bedienungsanleitung

Programat®CS4

Operating Instructions

Views of the Furnace, List of Parts 4

1. Introduction / Signs and Symbols 8

1.1 Preface

1.2 Signs and symbols

1.3 Notes regarding these Operating Instructions

1.4 Notes regarding the different voltage versions

1.5 Notes on the images in the Operating Instructions

2. Safety First 9

2.1 Indications

2.2 Health and safety instructions

3. Product Description 12

3.1 Components

3.2 Hazardous areas and safety equipment

3.3 Descriptions of functions

3.4 Accessories

3.5 Indications/contraindications

4. Installation and Initial Start-Up 13

4.1 Unpacking and checking the contents

4.2 Selecting the location

4.3 Assembly

4.4 Removing the furnace head

4.5 Initial start-up

5. Operation and Configuration 18

5.1 Introduction to the operation

5.2 Explanation of the key functions

5.3 Basic meaning of the display readouts

5.4 Program structure

5.5 Settable parameters and possible value ranges

5.6 Settings / test programs and information

5.7 Explanation of the display symbols

5.8 Explanation of the acoustic signals

5.9 OSD

6. Practical Use 23

6.1 Switching on the furnace

6.2 Loading for sintering programs

6.3 Sintering procedure with a standard program

6.4 Loading for glaze and crystallization programs

6.5 Glazing and crystallizing procedure with a standard program

6.6 Individual programs

6.7 Additional possibilities and special features of the furnace

6.8 Programming

7. Maintenance, Cleaning and Diagnosis 26

7.1 Cleaning of the sintering chamber and the heating elements

7.2 Monitoring and maintenance

7.3 Cleaning

7.4 Test programs

7.5 Stand-by

7.6 Temperature calibration

7.7 Service hint

8. What if ... 30

8.1 Error messages

8.2 Technical malfunctions

8.3 Repair

9. Product Specifications 32

9.1 Delivery form

9.2 Technical data

9.3 Acceptable operating conditions

9.4 Acceptable transportation and storage conditions

10. Appendix 33

10.1 Program table

Table of Contents

List of Parts

1 Insulation

2 Thermocouple

3 Sinter tray

4 Display

5 Frame plate

6 Sintering chamber

7 Furnace housing

8 Membrane-sealed keypad

9 On/Off switch

10 Heater fuse

11 Fuse holder

12 Power cord

13 Power socket

14 Rating plate

15 Furnace feet

16 Furnace head housing

17 Thermocouple plug

18 Power electronics plug

19 Plug fuse

20 Heater plug

21 Socket for the heater plug

22 Socket for the thermocouple plug

23 Socket for the power electronics plug

24 Leave spring

25 Air vents base

26 Cooling tray

27 Cooling tray fastening screw

28 Silicone washer

29 Hood

30 Attachment screw for hood

31 Air vents furnace head

32 Air vents rear panel

33 Furnace head mounting mark

34 Furnace base mounting mark

35 Furnace head mounting

36 Heating element

37 Sinter tray rest

38 Thermocouple cable

39 Power electronics cable

40 Connecting rod axis

41 Plug-in console

42 USB device interface

44 OSD

45 Spacer

46 Grounding band

47 Screw for grounding band

Please note that the list of parts applies to the entire

Operating Instructions. These parts and their numbers are

often referred to in later chapters.

List of Parts

827/28

15 25

18 23 21 20

47 19

24 35

910/11

10/11

42 45

Operating unit:

71 ESC key

72 ENTER key

73 Start key

74 Start LED

75 Stop key

76 + key

77 – key

78 Settings key

79 Cursor right key

80 Cursor left key

81 Information key

82 Program 1 key

83 Program 2 key

84 Program 3 key

85 Program 4 key

86 Next program key

87 Open furnace head

88 Close furnace head

100 Sinter tray

102 Cleaning brush 103 IPS e.max CAD Speed

Crystallization Tray

101 Sinter tray fork

80 77

101

100

102

103

83 84 85 86

72 71

1. Introduction / Signs and Symbols

1.1 Preface

Dear Customer

Thank you for having purchased the Programat® CS4. It is a sintering, glazing and crystallization furnace for dentists, who

are in need of such a furnace for the CAD/CAM technique. The furnace enables sintering and glazing of ZrO2materials

such as IPS e.max®ZirCAD as well as glazing and crystallization of IPS e.max CAD, for example. It has been especially

designed and constructed for this purpose.

The Programat CS4 has also been designed according to the latest industry standards. However, inappropriate use may

damage the equipment and be harmful to personnel. Please observe the relevant safety instructions and read these

Operating Instructions carefully.

Enjoy working with the Programat CS4.

1.2 Signs and symbols

The signs and symbols in these Operating Instructions facilitate the finding of important points and have the following

meanings:

Symbol Note

Risks and dangers

Important information

Contraindication

Burn hazard

Risk of crushing

The Operating Instructions must be read.

1.3 Notes regarding the Operating Instructions

Apparatus: Programat CS4

Target group: Dentists, dental professionals

These Operating Instructions facilitate the correct, safe and economical use of the furnace.

Should you lose the Operating Instructions, extra copies can be ordered at a nominal fee from your local Ivoclar Vivadent

Service Center or downloaded from the Internet free of charge (www.ivoclarvivadent.com).

1.4 Notes regarding the different voltage versions

The furnace has been designed for the following voltage range:

118–240V / 50–60 Hz

No manual switch-over is required for the use of the different voltage versions. Make sure that the local power supply

complies with the voltage indicated on the rating plate before operating the furnace.

Only use the supplied original power cord. Do not use an inadequately measured replacement.

1.5 Notes on the images in the Operating Instructions

All images and illustrations in these Operating Instructions are used for exemplification and the details are not authoritative

for the construction of the furnace. They are symbols which may slightly differ from the original, e.g. due to simplification.

2. Safety First

This chapter is especially important for individuals who work with

the Programat CS4 or who have to carry out maintenance or repair

work. This chapter must be read and the corresponding instructions

followed!

2.1 Indications

The Programat CS 4 has been especially designed for the sintering

and glazing of ZrO2materials such as IPS e.max ZirCAD as well as

glazing and crystallization of IPS e.max CAD, for example. The

Programat CS4 should be used for this purpose only. Other uses than

the ones stipulated, e.g. cooking of food, firing of other materials

etc., are contraindicated. The manufacturer does not assume any

liability for damage resulting from misuse. The user is solely

responsible for any risk resulting from failure to observe these

Instructions.

Further instructions to assure proper use of the furnace:

– The instructions, regulations and notes in these Operating

Instructions must be observed.

– The instructions, regulations and notes in the material’s

Instructions for Use must be observed.

– The furnace must be operated under the indicated environmental

and operating conditions (see chapter 9).

– The Programat CS4 must be properly maintained.

Do not use colouring liquids containing chlorine or hydro-

chloric acid in the Programat CS4 furnace. Due to the

aggressive components of the liquids, the furnace surfaces

or individual parts may be chemically corroded or damaged.

If colouring liquids containing chlorine or hydrochloric acid are used,

irritating gases may develop during the heating phase.

2.1.1

Contraindication

Do not carry the furnace by the

cooling tray.

2.1.2

Contraindication

Do not carry the furnace head by the

cables, since the cables and

connections may be damaged.

2.1.3

Contraindication

The furnace head must not be

removed from the furnace base as

long as the furnace head is connected

by means of the heater cable.

2.1.4

Contraindication

The furnace head is equipped with an

electric drive and can be operated by

means of the electronic controls. Never

open the furnace head by hand, since

this will damage the transmission.

2.1.5

Contraindication

Do not touch the thermocouple and

the heating element in the sintering

chamber. Avoid contact with the skin

(grease contamination), as the parts

may be prematurely damaged.

2.1.6

Contraindication

Never use the furnace without the sin-

ter tray. Use only the original Programat

sinter tray. Do not use the firing trays

or honey-combed trays from conven-

tional ceramic furnaces. Furthermore,

check the sinter tray for damage,

cracks or contamination before every

program start. If the sinter tray is

damaged, it must no longer be used.

A maximum of one sinter tray is to be

placed in the sintering chamber. Do not

stack the sinter trays.

2.1.7

Contraindication

Sinter trays must not be placed in the

area surrounding the firing plate, since

this will obstruct the closing of the

furnace head.

2.1.8

Contraindication

Foreign objects must not be placed on

the furnace head or the air vents.

Make sure that no liquids or other

foreign objects enter the air vents,

since this may result in an electric

shock.

2.1.9

Contraindication

Make sure that no liquids or other

foreign objects enter the furnace.

2.1.10

Contraindication

Do not insert any foreign objects into

the air vents. There is a risk of electric

shock!

2.1.11

Burn hazard

Never place objects in the hot firing

chamber by hand, since there is a burn

hazard. Always use the sinter tray fork

supplied for this purpose. Never touch

the hot surface of the furnace head, as

there is a burn hazard. Please also

observe the warnings on the furnace.

2.1.12

Risk of crushing / burn hazard

Never reach under the furnace head

with the hand or other parts of the

body during operation, since there is a

risk of crushing and a burn hazard.

2.1.13

Risks and dangers

This product contains ceramic fibres

and may release fibre dust. Do not use

compressed air or blow on the

furnace, thus distributing the dust in

the environment, and observe the

additional notes on page 11.

2.1.14

Risks and dangers

Do not use the furnace without spacer,

since the distance to the back wall has

to be kept!

2.1.15

Risks and dangers

The furnace must not be operated if the heating element

in the sintering chamber is damaged. There is a risk of

electric shock upon contact with the heating wire.

Inhaltsverzeichnis

Andere Ivoclar Vivadent Laborausrüstung Handbücher

Ivoclar Vivadent

Ivoclar Vivadent Programat P710 Handbuch

Ivoclar Vivadent

Ivoclar Vivadent PrograPrint Clean Handbuch

Ivoclar Vivadent

Ivoclar Vivadent Programat EP 5000 G2 Bedienungsanleitung

Ivoclar Vivadent

Ivoclar Vivadent Programat EP 5010 Handbuch

Ivoclar Vivadent

Ivoclar Vivadent Multilink Bedienungsanleitung

Ivoclar Vivadent

Ivoclar Vivadent IvoBase Series Bedienungsanleitung

Ivoclar Vivadent

Ivoclar Vivadent Programat EP3010 Handbuch

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung