JABSCO 22060-7125-C Bedienungsanleitung

Model 22060-7125 (C)

SANITARY PUMP

Standard Pressure Impeller SMS Ports

FEATURES

Body: Type 316 Stainless Steel

Impeller: Jabsco Sanitary Neoprene Compound

Seal: Sanitary Mechanical

Bearings: Ball/Roller Bearings

Shaft: Type 316 Stainless Steel

Ports: SMS 1145 Threads

Weight: 50 lb (23 kg) Approx.

APPLICATION

This product is specifically designed for farm pick-up

milk tanker trucks. Jabsco pumps are also available as

pedestal mounted or close-coupled units with capacities

to 100 GPM for other sanitary applications. Contact

factory for details.

OPERATING INSTRUCTIONS

1. INSTALLATION – Pump may be mounted in any

position. The rotation of the pump shaft determines

the location of the pump’s intake and discharge

ports. Refer to dimensional drawing. Pump is

normally assembled at factory for clockwise rotation

looking at end cover. If counterclockwise rotation is

desired, follow steps 1 and 2 of disassembly and

step 9 of assembly instructions to change direction

of impeller blade deflection under cam.

2. DRIVE – Belt or direct with flexible coupling. Belt

Drive: Overtight belt load will reduce pump bearing

life. Direct Drive: Clearance should be left between

drive shaft and pump shaft when installing coupling.

Always mount and align pump and drive shaft before

tightening the coupling set screw. If pulley or

coupling must be pressed on shaft, remove end

cover and impeller to support shaft from impeller end

during press operation. Do not hammer pulley or

coupling on shaft; this may damage bearing or seal.

Capacitor start motor is required to overcome

starting torque of impeller.

3. SPEEDS – 100 RPM to the maximum shown in the

performance curves. For longer pump life, operate

at lowest possible speeds. Lower speeds are

required for viscous liquids, consult the factory for

proper speeds and horsepower requirements.

4. SELF-PRIMING – Primes at low or high speeds. For

vertical dry suction lift of 10 feet, a minimum of 800

RPM is required. Pump will produce suction lift up to

22 feet when wet. BE SURE SUCTION LINES ARE

AIRTIGHT OR PUMP WILL NOT SELF-PRIME.

5. DISCHARGE - When transferring liquids further

than 25 feet, use 3" discharge line.

6. RUNNING DRY – Unit depends on liquid pumped

for lubrication. DO NOT RUN DRY for more than 30

seconds. Lack of liquid will damage the impeller.

7. PUMPAGE COMPATIBILITY – When corrosive

cleaning fluids are handled, pump life will be

prolonged if pump is flushed with a neutralizing

solution after each use or after each work day. A

Tungsten Carbide Seal variation is available for

pumping liquids that contain abrasives or are highly

corrosive.

8. PRESSURES – Consult Performance Curves for

maximum recommended pressures for pump in

continuous operation. If pressures exceed those

shown, consult the factory.

9. TEMPERATURES – The operating temperature limits

of the pump: 45° to 150° F (7° to 65° C).

N.B. 3A option to include Elastomers : EPDM and

Neoprene. Ports : Tri-Clamp, IDF, 3A and DIN11851.

10. CLEANING – Before using pump, it should be

disassembled and cleaned to remove any dust and

dirt resulting from storage or shipping. Wash parts in

standard cleaning solutions approved for handling

stainless steel. Thoroughly rinse before reassembly.

DO NOT USE IODINE BASED SANITIZERS as the

iodine attacks the elastomer materials used in the

impeller. All parts have been expertly machined and

polished. HANDLE WITH CARE. DO NOT DROP

OR MISHANDLE.

11. IMPELLER TORQUE – The torque required to

initiate rotation of a new impeller in a dry pump

body is:

Forward = 10.2 pounds force – feet

Reverse = 18.8 pounds force – feet

These values may vary slightly due to manufacturing

tolerances. Consult factory for more information.

12. SPARE PARTS – To avoid costly shutdowns, keep

a spare JABSCO impeller, seal and O-ring set

on hand.

MANUAL BY-PASS CIP ENDCOVER FOR

JABSCO PUMPS

Jabsco stainless-steel milk collection tanker pumps are

easily cleaned in place at the same time that the tanker

is cleaned. This can be achieved in 2 ways:

By running the pump to circulate the cleaning liquid

through the pipe work and metering equipment; a

separate land-based CIP pump may be used to provide

the pressure to the tank spray balls. The pump and

impeller can withstand hot water and proprietary

chemicals for the duration of the cleaning cycle.

Alternatively, if the pump is fitted with the Jabsco Manual

By-pass CIP Endcover Assembly the complete system

can be cleaned with the milk collection pump static. This

brings several advantages:

• No Need To Run The Vehicle Engine: The hydraulic

system is not required during cleaning so no engine

fumes are generated in the CIP bay, noise is much

reduced and unnecessary fuel consumption is

eliminated.

• More Effective Cleaning: Tests have shown that

cleaning is more thorough with the Manual By-pass

End Cover fitted.

• Extended Pump Life: During the cleaning cycle the

pump is at greatest risk of running dry. If the cleaning

fluid runs out e.g. during change-over from CIP fluid

to rinse water, the pump impeller can be damaged if

the pump is running. By cleaning the pump static,

impeller life will be extended.

This end cover assembly fits in place of the standard

pump end cover and contains a piston which moves

back under the pressure from the separate CIP cleaning

pump allowing cleaning fluid to by-pass the ends of the

impeller.

CLEANING

Before starting the CIP pump, the center screw (24) of

the manual by-pass assembly is loosened at least 10

turns counter-clockwise. This allows the piston (22) to

travel back under the pressure of the CIP liquid. The

system can then be cleaned using the regime

established by the tanker operator; the pump does not

need to be run or attended to in any way during cleaning.

After cleaning, the center screw is tightened clockwise

ready for normal pumping.

PIPE WORK

The pipe work can be arranged in two ways during cleaning:

1. Parallel piping: the flow from the CIP pump is split at

a tee-piece so part of the flow is taken direct to the

tanker spray balls while the rest flows through the

pump and the metering equipment. See fig 1.

2. Series piping: all the CIP flow is directed through the

pump and metering equipment and then on to spray

balls. See fig 2.

N.B. Do not clean with Phosphoric Acid.

EXPLODED VIEW

SPARE PARTS LIST

Part

Key Description Qty. Number

1 Clamp Screw 1 21908-0001

2 Clamp Frame 1 21909-0000

2 Clamp Frame CIP 1 286420000

3 End Cover 1 22007-0000

3 End Cover CIP 1 287120000

4 O-ring 2 92000-1213

5 Impeller 1 218990005B

6 Body 1 28704-7000

7 Wearplate 1 21937-0000

8 Seal Kit 1 226448000B

9 V-Ring 1 X5280-015

10 O-ring 1 X4020-379A

* Oring CIP 1 X4020424A

11 Seal Housing 1 23933-0000

Part

Key Description Qty. Number

12 Lip Seal 1 X5280-011

13 Lip Seal Kit 1 92701-0880

14 Retaining Ring (Hsg) 2 91701-4391

15 Bearing Hsg 1 22064-0100

16 Roller Bearing (front) 1 92601-0460

17 Shaft 1 219780000

18 Key 1 91402-0270

19 Ball Bearing (rear) 1 92601-0450

20 Retaining ring (shaft) 1 91700-2870

* By-Pass Endcover Kit 1 2870-0000

*22 Clamp Screw CIP 1 287140000

*24 End Cover Piston CIP 1 287110000

* Handle Assy CIP End Cover 1 287180000

*Not Shown

SERVICE INSTRUCTIONS

DISASSEMBLY

1. Remove end cover clamp. Remove end cover and

O-ring.

2. Slide body, complete with impeller and wearplate,

from shaft assembly. Remove impeller from body.

3. Remove mechanical seal from shaft. Use extreme

care not to mar shaft surface. Remove seal seat and

O-ring from recess in wearplate.

4. From the drive end of the bearing housing, pry out

bearing seal by inserting a screwdriver blade

between OD of the seal and housing. Remove

retaining ring. Very carefully withdraw shaft and

bearing assembly.

5. Remove inner bearing seal and retaining ring.

6. To remove bearings from shaft an arbor press is

required. If an arbor press is not available then a

bearing extractor may be used. Supporting inner

race of bearing, apply a steady pressure on shaft

until bearing slides free. Repeat this procedure to

remove second bearing.

ASSEMBLY

1. To replace bearing on shaft. Support bearing on its

inner race and locate shaft onto bearing. Apply a

steady pressure to the shaft until bearing locates

against shoulder on shaft. Repeat for second bearing.

2. Fit retaining ring and bearing seal into impeller end

of bearing housing. Spring on bearing seal to face

outwards.

3. Apply bearing grease around and between bearings,

filling cavity between bearings two thirds full. Smear

grease on shaft where bearing seal locates. Push

shaft and bearing assembly into bearing housing.

4. Replace the two retaining rings and outer bearing

seal, with spring facing outwards, on drive end of

bearing housing.

5. Replace mechanical seal by sliding positioning

washer onto shaft up to locating shoulder, then

smear shaft with light lubricating oil. Push on seal

gently until it engages with washer. Fit O-ring and

seal seat into wearplate.

6. Insert impeller in pump body. Fit O-ring on each end

of the pump body. Fit wearplate to body.

7. Slide wearplate and body assembly over shaft,

positioning wearplate in housing.

8. Fit end cover and end cover clamp. Clamp should

be hand tightened. Do not use wrench or hammer.

9. Changing Pump Rotation (looking at end cover):

Clockwise Rotation: Insert impeller into pump

body with blades bending counterclockwise.

Counter-clockwise Rotation: Insert impeller into

pump body with blades bending clockwise.

Warranty: All products of the company are sold and all services of the company are offered subject to the company’s warranty and terms and conditions of sale, copies of which will be furnished upon request. The information pro-

vided herein is for guidance only, it does not constitute a guarantee of the performance or specification of any individual product or component.

DIMENSIONAL DRAWING

Inches (Millimeters)

430000606RWD Rev:0312

SMS

Dieses Handbuch passt für folgende Modelle

Andere JABSCO Wasserpumpe Handbücher

JABSCO

JABSCO 12490 Series Bedienungsanleitung

JABSCO

JABSCO 30560-0 Series Bedienungsanleitung

JABSCO

JABSCO 30296 Series Bedienungsanleitung

JABSCO

JABSCO Hy-Line Bedienungsanleitung

JABSCO

JABSCO 50890 Bedienungsanleitung

JABSCO

JABSCO 28 Series Bedienungsanleitung

JABSCO

JABSCO 30520-310 Bedienungsanleitung

JABSCO

JABSCO 36680-2 Series Bedienungsanleitung

JABSCO

JABSCO 36960-2 Series Bedienungsanleitung

JABSCO

JABSCO 30580-0 Series Bedienungsanleitung

JABSCO

JABSCO 30510-0 Series Bedienungsanleitung

JABSCO

JABSCO 50270 Series Betriebsanleitung

JABSCO

JABSCO Puppy 12560-0001 Bedienungsanleitung

JABSCO

JABSCO 32605 Series Bedienungsanleitung

JABSCO

JABSCO 30520-5 Series Bedienungsanleitung

JABSCO

JABSCO 29200-0120 Bedienungsanleitung

JABSCO

JABSCO 50870 Series Bedienungsanleitung

JABSCO

JABSCO 50840 Series Bedienungsanleitung

JABSCO

JABSCO 23920-9503 Bedienungsanleitung

JABSCO

JABSCO 30570-2 series Bedienungsanleitung

JABSCO

JABSCO 37202-2712 Bedienungsanleitung

JABSCO

JABSCO 18690-0000 Bedienungsanleitung

JABSCO

JABSCO 30560-0 Series Bedienungsanleitung

JABSCO

JABSCO 4720 Series Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung