Janitza UMG 806 Gebrauchsanweisung

Janitza electronics GmbH

Vor dem Polstück 6

35633 Lahnau, Germany

Support tel. +49 6441 9642-22

Email: [email protected]

www.janitza.com

Doc. no.: 2.064.005.2b Date: 05/2020

Modular Power Analyzer

UMG 806

User manual and technical data

(Firmware 1.18)

UMG 806 www.janitza.de

UMG 806

Modular multifunctional meter for

recording energy quantities

Doc. no.: 2.064.005.2b

Date: 05/2020

The German version is the original edition of the documentation

www.janitza.de UMG 806

Subject to technical changes.

The contents of our documentation have been compiled with great care and reﬂect the current state of

the information available to us. Nonetheless, we wish to point out that updates of this document are not

always possible at the same time as technical reﬁnements are implemented in our products. Please see

our website under www.janitza.de for the current version.

Please see our website under www.janitza.de for the current version.

UMG 806 www.janitza.de

Table of contents

1. Information on the device and the user manual 10

1. 1 Disclaimer 10

1. 2 Copyright notice 10

1. 3 Technical changes 10

1. 4 About this user manual 10

1. 5 Defective device/disposal 11

2. Safety 12

2. 1 Display of warning notices and safety information 12

2. 2 Hazard levels 12

2. 3 Product safety 13

2. 4 Dangers when handling the device 13

2. 5 Electrically qualiﬁed personnel 14

2. 6 Warranty in the event of damage 14

2. 7 Safety information for handling current transformers and measurement devices

with residual current measurement 14

2. 8 Handling batteries/accumulators 15

3. Product description 16

3. 1 Device description 16

3. 2 Incoming goods inspection 16

3. 3 Intended use 17

3. 4 Performance characteristics 18

3. 5 EU conformity declaration 18

3. 6 Scope of delivery 18

3. 7 Accessories 18

3. 8 Transformer 18

3. 9 Operating concept 19

3. 10 GridVis®network analysis software 19

3. 11 Overview of the range of functions 20

3. 11. 1 Conﬁguration on the device (via 2 buttons) 20

3. 11. 2 Communication 20

3. 11. 3 Measured values / functions 20

www.janitza.de UMG 806

4. Structure of the device 22

4. 1 Front panel and display 22

4. 2 Front view / side view 24

4. 3 Identiﬁcation of the device (rating plate) 25

5. Mounting 26

5. 1 Installation location 26

5. 2 Mounting orientation and attachment 26

6. Grid systems 28

7. Installation 29

7. 1 Nominal voltages 29

7. 1. 1 Three-phase 4-conductor network 29

7. 1. 2 Three-phase 3-conductor network 30

7. 2 Disconnect switch 31

7. 3 Supply voltage 31

7. 4 Voltage measurement 32

7. 4. 1 Overvoltage 32

7. 4. 2 Mains frequency 32

7. 5 Current measurement 33

7. 5. 1 Connection variants 34

7. 5. 2 Summation current measurement 35

7. 5. 3 Ammeter 35

7. 6 Residual current measurement (RCM) 36

7. 6. 1 Current direction of the residual current transformers 36

7. 6. 2 Residual current transformer example 37

7. 6. 3 Connection example - Residual current monitoring 37

7. 7 Temperature measurement 38

7. 8 RS-485 interface (serial interface) 39

7. 8. 1 Shielding 40

7. 8. 2 Termination resistors/Termination 40

7. 8. 3 Bus structure (bus segment) 41

7. 9 Digital output 42

UMG 806 www.janitza.de

8. PC connection 43

8. 1 Connection to a PC 43

9. Operation and button functions 44

9. 1 Controls 44

9. 2 Function buttons 44

9. 3 Operation 44

9. 3. 1 Display mode 44

9. 3. 2 Conﬁguration mode 44

9. 4 Password 44

9. 5 Overview of measuring display (display mode) 45

9. 6 Examples of basic measuring displays 46

9. 7 Examples of energy measurement 47

9. 8 Examples of power quality 47

9. 9 Example of time display 47

9. 10 Example of active EI1 module 47

9. 11 Example of active ED1 module 47

10. Conﬁguration 48

10. 1 Conﬁguration mode 48

10. 2 Conﬁguration 48

10. 2. 1 Conﬁguring the network system 48

10. 2. 2 Conﬁguring the current transformer ratios 49

10. 2. 3 Example: Conﬁguring the current transformer ratios I1-I3 49

10. 2. 4 Example: Conﬁguring the current transformer ratios of residual current

measurement input I5 (700:1) 50

10. 2. 5 Conﬁguring the voltage transformer ratios 51

10. 2. 6 Example: Conﬁguring the voltage transformer ratios 51

10. 2. 7 Conﬁguring the RS-485 interface (Modbus) 52

10. 2. 8 Conﬁguring the Ethernet interface 52

10. 3 Parameter list 54

www.janitza.de UMG 806

11. Commissioning 58

11. 1 Supply voltage 58

11. 2 Measured voltage 58

11. 3 Frequency measurement 58

11. 4 Measured current 59

11. 5 Checking the phase assignment 59

11. 6 Checking the power measurement 59

11. 7 Checking measurement 59

11. 8 Checking individual power 59

11. 9 Checking summation power 59

12. Connection example, UMG 806 60

13. Expansion modules 61

13. 1 Module types 61

13. 1. 1 806-EC1 module 61

13. 1. 2 806-ED1 module 61

13. 1. 3 806-EI1 module 61

13. 2 Installing the modules 63

13. 3 Front / side views 64

13. 3. 1 806-EC1 module 64

13. 3. 2 806-ED1 module 64

13. 3. 3 806-EI1 module 65

13. 4 Connection examples 65

13. 4. 1 806-ED1 module 65

13. 4. 2 806-EI1 module 65

13. 5 Conﬁgure/activate module 66

13. 6 Display examples 66

13. 6. 1 ED1 module 66

13. 6. 2 EI1 module 66

13. 7 EC1 module 67

13. 7. 1 Front LEDs and reset button 67

13. 7. 2 Conﬁguring the Ethernet interface 67

13. 8 Relay outputs of modules ED1 and EI1 69

13. 8. 1 Table "Parameters of the alarm elements" - Parameter address 412 70

13. 8. 2 Alarm elements and units of the alarm limit values 71

UMG 806 www.janitza.de

14. Service and maintenance 72

14. 1 Repair and calibration 72

14. 2 Front panel foil and display 72

14. 3 Service 72

14. 4 Device adjustment 72

14. 5 Clock/Battery 73

14. 6 Procedure in the event of a malfunction 74

15. Technical data 75

15. 1 Technical data, UMG 806 75

15. 2 Performance characteristics of functions 79

15. 3 Technical data of the modules 80

www.janitza.de UMG 806

UMG 806 www.janitza.de

1. Information on the device and the user manual

1.1 Disclaimer

Compliance with the informational products for

the device is a prerequisite for safe operation and

attaining the stated performance characteristics

and product features.

Janitza electronics GmbH assumes no liability for

bodily injury, material damage or ﬁnancial losses

which result from disregard of the informational

products.

Ensure that your informational products are readily

accessible in a legible form.

1.2 Copyright notice

Any reproduction, processing, distribution or other

use of this informational product, in whole or in

part, is prohibited.

All trademarks and the rights arising from them

are the property of the respective owners of these

rights.

1.3 Technical changes

· Make sure that your device matches the user

manual.

· This user manual applies to the UMG 806.

Separate validities and distinctions are marked.

· First read and understand the documents

associated with the product.

· Keep the documents associated with the product

available for the entire service life and pass them

on to any possible subsequent users.

· Find out about device revisions and the

associated modiﬁcations of the documentation

associated with your product at www.janitza.de.

1.4 About this user manual

If you have questions, suggestions or ideas for

improvement of the user manual, please let us

know via email at: [email protected].

INFORMATION

This user manual describes the UMG 806 and

provides information on the operation of the device.

Also consult the additional documentation relevant

for this user manual, such as:

· Installation instructions.

· Data sheet.

· Safety information.

· As applicable, documents for expansion

modules.

· Online help for the network visualization software

GridVis®.

Andere Handbücher für UMG 806

Inhaltsverzeichnis

Andere janitza Messgerät Handbücher

janitza

janitza UMG 605US Bedienungsanleitung

janitza

janitza UMG 96-S2 Gebrauchsanweisung

janitza

janitza UMG 806 Gebrauchsanweisung

janitza

janitza 800-CT8-A Bedienungsanleitung

janitza

janitza EM3-80 Bedienungsanleitung

janitza

janitza UMG 96S Bedienungsanleitung

janitza

janitza UMG 511 Bedienungsanleitung

janitza

janitza UMG 96 RM-M Gebrauchsanweisung

janitza

janitza UMG 103-CBM Bedienungsanleitung

janitza

janitza UMG 801 Gebrauchsanweisung

janitza

janitza UMG 96 RM-E Bedienungsanleitung

janitza

janitza FBM Series Bedienungsanleitung

janitza

janitza UMG96L Bedienungsanleitung

janitza

janitza UMG 96RM-P Bedienungsanleitung

janitza

janitza optec UMG-96 Bedienungsanleitung

janitza

janitza UMG 512 PRO Bedienungsanleitung

janitza

janitza UMG 96-PA Gebrauchsanweisung

janitza

janitza UMG 804 Gebrauchsanweisung

janitza

janitza UMG 104 Gebrauchsanweisung

janitza

janitza UMG 801 Bedienungsanleitung

janitza

janitza UMG96RM Bedienungsanleitung

janitza

janitza UMG 801 Bedienungsanleitung

janitza

janitza 800-CT8-LP Bedienungsanleitung

janitza

janitza UMG507 Bedienungs- und Montageanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung