jbc DSS Bedienungsanleitung
Box includes one stand according to purchased reference.
This manual corresponds to the following references:
DS-SF (for DS360)
DR-SF (for DR560)
Packing List
Stand for
DR560 Desoldering Iron ..................... 1 unit
Stand for
DS360 Micro Desoldering Iron ............ 1unit
Cable Holder ................. 1 unit
Ref. 0024028 (already assembled)
Stand Cable 1m ............ 1 unit
Ref. 0024227
Manual ............................. 1 unit
Ref. 0027183
Sponge for Modular
Tool Stands ................... 1 unit
Ref. S7034
Brass Wool .................... 1 unit
Ref. CL6210
Connecting Clip Set .... 1 unit
Ref. 0011356 (includes 2 pieces)
The following items are included in each stand:
2
Features and Connections
To Tool
To Control Unit
Wiper for
Modular Tool Stand
Ref. CL7899
Adjustable
Cable Collector
Ref. CC1001
Quick Tip Changer
Tip Storage
Ajustable Tool Holder
Brass Wool
(inside)
Sponge
www.jbctools.com
3
Assembly
Cable Collector and Adjustable Tool Holder
Adjust the tool holder angle to
suit the work position.
The cable collector is flexible.
It accompanies and adapts
to the movements during the
soldering process.Insert the cable into the clip
and then insert into the cable
collector. Do not leave the
cable longer than necessary
to reach the work area freely.
The wiper offers different ways to
clean the cartridge tips. If desired
use the included sponge.
4
Brass Wool
Ref. CL6210
Very effective cleaning method. Leaves a small layer of solder on
the tip preventing oxidation between cleaning and rewetting.
If the tip is very dirty, JBC recommends first the cleaning with the
wiper to remove excess solder.
Tap gently to remove excess
solder.
Use the slots to remove the
remaining particles.
Wiper
Tapping Wiping Sponge
The softest cleaning method.
Keep the sponge damp with
distilled water when working to
avoid tip wear.
The integrated wiper offers different ways to clean the cartridge tips.
Tip Cleaner
Select the option to suit your needs and improve the thermal transfer of the tip.
www.jbctools.com
5
DS360
Ref. DS-SF
Place the Soldering Iron with the assembled tip
in the extractor groove, pull the tool towards and
remove the tip.
Put on the new tip and press slightly to ensure
its correct postion.
Unused tips can be stored in the extractor
openings.
The Spanner is used to unscrew and replace
the tips. When not in use it can be stored inside
the extractor.
Unused tips can be stored in the extractor
openings.
Tip Extractor
Spanner
Tip Storage
Tip Storage
Ref. DR-SF
Wiper and Brass Wool Replacement
Lift the wiper at its front edge.
The wiper and brass wool can easily be removed for cleaning or replacement when they are worn.
Remove the wiper by pulling
it out.
Replace the brass wool with a
new one when it is worn out.
Place the wiper back o replace
them if desired.
6
Accessories
Suction Extension Tube Kit
Ref. A1287
Length: 1.5m
Stand extension cable
Ref. A1286
Length: 1.5m
Stand cable
www.jbctools.com
7
Clean periodically
Maintenance
Before carrying out maintenance or storage,
always unplug the stand from the station and
the tool.
- Use a damp cloth to clean the stand.
Alcohol can be used only when cleaning
the metal parts.
- Check periodically that the metal parts of
the tool/stand are clean so that the station
can check the tool’s status.
- Periodically check all cables and tube
connections.
- Replace any defective or damaged parts.
Use original JBC spare parts only.
- Repairs should only be performed by a
JBC authorized technical service.
8
Safety
- Do not use the stand for any other purpose than soldering or rework.
- The power cord must be plugged into approved bases. Be sure that it is properly grounded
before use. When unplugging it, hold the plug, not the wire.
- The tool should be placed in the stand when not in use in order to activate the sleep mode.
The soldering tip, the metal part of the tool and the stand may still be hot even when the station
is turned off. Handle with care, including when adjusting the stand position.
- Avoid the contact of flux with skin or eyes to prevent irritation.
- Be careful with the fumes produced when soldering.
- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when
working to avoid personal harm.
- Utmost care must be taken with liquid tin waste which can cause burns.
- This appliance can be used by children over the age of eight and also persons with reduced
physical, sensory or mental capabilities or lack of experience provided that they have been given
adequate supervision or instruction concerning use of the appliance and understand the hazards
involved. Children must not play with the appliance.
- Maintenance must not be carried out by children unless supervised.
It is imperative to follow safety guidelines to prevent electric
shock, injury, fire or explosion.
www.jbctools.com
9
Notes
10
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Andere jbc Elektrowerkzeuge Handbücher
jbc
jbc AM120-A Bedienungsanleitung
jbc
jbc AP250 Bedienungsanleitung
jbc
jbc SF250 Bedienungsanleitung
jbc
jbc HT420-A Bedienungsanleitung
jbc
jbc AP250 Bedienungsanleitung
jbc
jbc DS360 Bedienungsanleitung
jbc
jbc AD 8211 Bedienungsanleitung
jbc
jbc JT Series Bedienungsanleitung
jbc
jbc JT Bedienungsanleitung
jbc
jbc DS360 Bedienungsanleitung
jbc
jbc TRA245 Bedienungsanleitung
jbc
jbc JTSE-QA Bedienungsanleitung
jbc
jbc TR245-A Bedienungsanleitung
jbc
jbc MD 2960 Bedienungsanleitung
jbc
jbc ALE250 Bedienungsanleitung
jbc
jbc AL250-B Bedienungsanleitung
jbc
jbc TE Bedienungsanleitung
jbc
jbc TRA245-B Bedienungsanleitung
jbc
jbc advanced Series Bedienungsanleitung
jbc
jbc MV-A Bedienungsanleitung
