Jbc SF-110VB Bedienungsanleitung

Automatic Solder Feeder

Ref. SF-110VB/SF-210VB

www.jbctools.com

Packing List

The following items should be included:

Manual ...............................1 unit

Ref. 001633

Allen key Ø 1,5 ................1 unit

Ref. 0741610

SF Control Unit ............. 1 unit

Ref. SF-1B (100 -120V)

SF-2B (230V)

Allen key Ø 2,5 ................1 unit

R ef. 0 012574

Reel support ................ 1 unit

Ref. 0019301(x1)

0018033 (x1)

0003412 (x2)

Power cable .................... 1 unit

Ref. 0009417 (100V/120V)

0009401 (230V)

Spanner ............................ 1 unit

Ref. 0 017631

Guide Set ........................1 unit

Ref. GSF10V-B

Automatic Solder Feeder

Ref. SF-B

lock rings

Solder Feed

Handle .............................. 1 unit

Ref. SF280-A

www.jbctools.com

Power Socket

Fuse

RJ12 connection

for Robot System

RJ12 connection for Station

USB-B connector

Tin wire inlet

Features

Solder

Feed Handle

Ref. SF280-A

Control Unit

Main Switch

Control Screen

www.jbctools.com

Tool assembly

Connect the tool to the control unit.

1. Push the guide tube to the end

and tighten the screw.

2. Connect the jack.

Load the solder wire

1. Put the reel into its support.

2. Feed the wire into the input nozzle (2) until it reaches the wheels.

Input

nozzle

3. Use the Tin Reload Process

in Main Menu by pressing

the tool button.

4. Make sure the wire passes

through the nozzle.

insert to the end

Changing the wheels and the blade

1. Use the allen key and the spanner to loosen

the screws.

2. Replace the guide wheel and the blade for

the new ones.

Guide

wheel Blade

clamp

Blade

For this operation, disconnect the unit.

* Handle with care to avoid any cuts with the

blade because it is sharp.

2. You can easily adjust the length of the tube by opening the tube clamp.

Replacing the guide tube

1. Open the guide clamp, take off the guide tube and insert the new one.

For this operation, disconnect the tool from the control unit.

www.jbctools.com

Back

Setting Program 35

Continuous Mode Discontinuous Mode Program 35

Speed Length Length

STEP1 STEP2

Speed Speed

Supplied: 2.0mm 0:05 40% 40%

mm/s mm mm

mm/s mm/s

40.0 1.5 1.5

20.0 20.0

STEP3

Length Speed

mm mm/s

5.0 20.0

STEP 1

STEP 2

STEP 3

Back

Edit Program

mm/s

STEP 1 STEP 2 STEP 3

5.0 3.0 1.5

20.0 24.5 20.0

FACTORY 1 1Program35

FACTORY1

2Program22

LAB2

3Program35

FACTORY1

Program Concatenation

Back

Work Screen

Control Process

Choose between continuous, discontinuous and program mode:

Program mode

With the SF you can define up to 35 dynamic programs. In each one you can configure up to 3

steps with different lenght wire and dispensing speed.

Execute them sequentially and cyclically with the ‘Edit Concatenation List’ option.

Main Menu

5 Tin Reload Process

6 Counters

7 Software Version

1 Reset settings

Station settings

Tool settings

4 Programs Settings

Exit

1 Length units*

Beep Off

3 PIN On

4 Change PIN

1 Mode

Discontinuous

Backward Off

Tool Settings

Station Settings

Back

1 Edit Program

Delete Program

Edit Concatenation List

Program Settings

ckward Forward

Reload Process

1 Plugged hours

7605

Working hours 350

3 Supplied mm 560

4 Work Cycles 75830

Counters

Back

5 Reset partial counters

Press Enter to toggle*

Press enter when finished

Back

5 Station Locket

Off

Robot Mode Off

Screen Menu

Original PIN: 0105

Control Process

*switch total and partial

counters

*switch mm and inches

www.jbctools.com

Solder Wire Ø (mm) With Solder Wire Perforation Solder Wire Ø (mm) Without Solder Wire Perforation

- - 0.5-0.6 GSF05D-B

0.8 GSF08V-B 0.7-0.8 GSF08D-B

1.0 GSF10V-B 0.9-1.0 GSF10D-B

1.5 GSF15V-B 1.2-1.5 GSF15D-B

Accesories

Solder Feed Handle Stand

Ref. SF-SE

It prevents the SF280-A Solder Feed Handle

from rolling away while working.

Different guide sets are available depending on the solder wire used:

Before carrying out maintenance, always allow

the equipment to cool down.

- Clean the station screen with a glass cleaner

or a damp cloth.

- Use a damp cloth to clean the casing and the

tool. Alcohol can only be used to clean the

metal parts.

- Periodically check all cables and tubes.

Clean periodically

Maintenance

1. Pull off the fuse holder and remove the

fuse. If necessary use a tool to lever it off.

2. Insert the new fuse into the fuse holder

and return it to the station.

- Replace a blown fuse as follows:

- Replace any defective or damaged parts. Use original JBC spare parts only.

- Repairs should only be performed by a JBC authorized technical service.

www.jbctools.com

- Do not use the units for any purpose other than soldering or rework. Incorrect use may cause fire.

- The power cord must be plugged into approved bases. Make sure that it is properly grounded

before use. When unplugging it, hold the plug, not the wire.

- Do not work on electrically live parts.

- The tool should be placed in the stand when not in use.

Handle with care, including when adjusting the stand position.

- Do not leave the appliance unattended when it is on.

- Do not cover the ventilation grills. Heat can cause inflamable products to ignite.

- Avoid the contact of flux with skin or eyes to prevent irritation.

- Be careful with the fumes produced while soldering.

- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when

working to avoid personal harm.

- Utmost care must be taken with liquid tin waste which can cause burns.

- This appliance can be used by children over the age of eight as well as persons with reduced

physical, sensory or mental capabilities or lacking experience provided that they have been given

adequate supervision or instruction concerning use of the appliance and understand the hazards

involved. Children must not play with the appliance.

- Maintenance must not be carried out by children unless supervised.

Safety

It is imperative to follow safety guidelines to prevent electric

shock, injury, fire or explosion.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere jbc Lötpistole Handbücher

Beliebte Lötpistole Handbücher anderer Marken

Bakon

Bakon 3200 Bedienungsanleitung

Proxxon

Proxxon Gaslotset MGS Bedienungsanleitung

HAKO

HAKO FX-8804 Bedienungsanleitung

SATA

SATA 02002A Bedienungsanleitung

Velleman

Velleman HRJA151 Bedienungsanleitung

Weller

Weller WSM 1 Bedienungsanleitung

Vishay Precision Group

Vishay Precision Group Micro-Measurements Mark V Montageanleitung

ersa

ersa i-CON 1V Bedienungsanleitung

Hakko Electronics

Hakko Electronics FX-100 Bedienungsanleitung

Weller

Weller WAD 101 Bedienungsanleitung

Weller

Weller WXD 2 Bedienungsanleitung

AlienTek

AlienTek T100 Bedienungsanleitung

Atten

Atten ATETOOL AT-689A Bedienungsanleitung

Surtek

Surtek 112554 Abmessungen und Installationsanleitung

Parkside

Parkside PLBS 30 A1 Bedienungsanleitung

BlackJack SolderWerks

BlackJack SolderWerks BK8000 Bedienungsanleitung

Weller

Weller WX1 Bedienungsanleitung

multicomp pro

multicomp pro MP740893 Bedienungsanleitung

jbc SF-110VB Bedienungsanleitung

Beliebte Lötpistole Handbücher anderer Marken