Jbc PHB-KA Series Bedienungsanleitung

Español 11

Convection Preheater Set

Ref. PHB-KA

English 2

Page

INSTRUCTION MANUAL

www.jbctools.com

Packing List

The following items should be included:

Heater Unit Console

Power Cord .............................................. 1 unit

Ref. 0009417 (100V/120V)

0009401 (230V)

Thermocouple .............. 1 unit

Ref. PH218

Kapton Tape .................. 1 unit

Ref. PH217

Manual ............................ 1 unit

Ref. 0016815

Ref. PHB-KA

Convection Preheater Set

Convection Preheater ............................................................................................................................. 1 unit

Ref. PHB-1A (120V)

PHB-2A (230V)

PHB-9A (100V)

Convection Preheater Support ........... 1 unit

Ref. PHB-SA

INSTRUCTION MANUAL

www.jbctools.com

Features

Pedal socket (optional)

Ref. P-005

Heating Areas

Power socket

Power

Fixing brackets

for PHB-SA

Convection Preheater

Support

Heater Unit

Console

Control Unit Start / Stop

Auxiliary Thermocouple (Type K) Input

Thermocouple

(Type K)

Ref. PH218

USB-B

connector to PC:

Update software

Zone A Zone B

www.jbctools.com

Height Adjustment

It allows adjustment for 3 heights between the PCB and the Heating Area of the PHB-A Heater Unit.

Low level

High level

Medium level

28 mm

38 mm

48 mm

PHB-SA Features

Adjustable slot clamps

for switching PCBs

Adjusting system

for changing height

Clamp knobs

Sliding

guides

Allen key

Changing PCBs of the same batch

Loosen one sliding guide, pull back and lift

out the PCB.

The support lets you place PCBs of the same batch so as to always heat the same area.

Use the sliding guides to change the PCBs.

Position it and tighten the sliding guide knobs.

Removing the PCB Placing another PCB

Cap Guide PCB

Use the 4 caps to place larger PCBs than the PHB-SA Support or over 3mm thick.

1. Remove both guides by

untightening the 8 screws.

2. Place the PCB on the 4

rubber caps.

3. The PCB is ready to work.

Reworking large PCBs

Clamp knobs

www.jbctools.com

Profiles by Temperature

The usual way to run a profile is using the Thermocouple (TC) connected to the Control Input of the

console. JBC offers 3 predefined profiles (JBCset) and 20 profiles ready for you to personalize.

Why convection? Perfect heat distribution

Convection technology offers a uniform heat distribution over the whole working area of the

Preheater. This gradual heating system reduces the risk of thermal stress on the PCB.

Operation

JBCset profiles

There are 3 profiles predefined by JBC: A, B and C. The difference between them is the number

of steps: 2, 3 or 4. The thicker your PCB is and the more layers it contains, the more steps are

needed to obtain a gradual warming.

These profiles are not modifiable but they can be used as a template to create your own profiles.

JBCset A

2 steps

JBCset B

3 steps

JBCset C

4 steps

For repetitive jobs we recommend running profiles without the Thermocouple (TC). Once any

profile has been run to the end, the system has all the process data which you can save.

Once it is saved, you can run this profile without connecting the Thermocouple (TC). The heating

process will the same as long as the same working conditions are respected.

User profiles

You can create your own profiles from the JBCset profiles. On the work screen of the profile,

press the Enter button and choose the option Edit profile.

Power or Temperature Modes

The unit works at the selected power or temperature during the defined time. These parameters can

be modified from the work screen by pressing the Enter button and the Edit parameters menu.

To see the current temperature you must plug the Thermocouple (TC) into the Control connector.

PCB reference

specifications:

FR4 1,6mm thick

and 2 layers. FR4 2,2mm thick

and 6 layers.

FR4 1,6mm thick

and 6 layers.

Profiles set using the low position of the PHB-SA Support (28 mm in height between the PCB and the heating area).

Recommended Guidelines

1. Place the Thermocouple (TC) as near as possible to the component being worked on.

2. If there are any sensitive components, use the Auxiliary Thermocouple as protection.

You can select the protection temperature in Station settings. If the selected temperature is

reached, the Heater Unit will stop the process and a warning message will be shown.

3. IPC* does not recommend exceeding ramp-up rates over 3 - 4 °C / sec (5 - 7 °F / sec) so as to

reduce the risk of thermal stress on the PCB.

* IPC was founded in the U.S. in 1957 as the Institute for Printed Circuits and is committed to becoming the

most recognized international industry association for the electronics manufacturing industry.

Fix the TC with Kapton Tape

Auxiliary Thermocouple (TC)

www.jbctools.com

Display Control

www.jbctools.com

Maintenance

Before carrying out maintenance or storage, always allow the equipment and the support to cool.

- Check periodically that the PHB-KA is clean.

- Use a damp cloth when cleaning. Alcohol

can only be used to clean the metal parts.

- Only if it is absolutely necessary and

if cleaning with isopropyl alcohol (IPA) is not

enough, itisrecommended touse a scraper

to remove dirt in the glass area.

- Replace any defective or damaged parts.

Use original JBC spare parts only.

- Repairs should only be performed by a JBC

authorized technical service.

Clean periodically

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere jbc Lötpistole Handbücher

Beliebte Lötpistole Handbücher anderer Marken

Bakon

Bakon 3200 Bedienungsanleitung

Proxxon

Proxxon Gaslotset MGS Bedienungsanleitung

HAKO

HAKO FX-8804 Bedienungsanleitung

SATA

SATA 02002A Bedienungsanleitung

Velleman

Velleman HRJA151 Bedienungsanleitung

Weller

Weller WSM 1 Bedienungsanleitung

Vishay Precision Group

Vishay Precision Group Micro-Measurements Mark V Montageanleitung

ersa

ersa i-CON 1V Bedienungsanleitung

Hakko Electronics

Hakko Electronics FX-100 Bedienungsanleitung

Weller

Weller WAD 101 Bedienungsanleitung

Weller

Weller WXD 2 Bedienungsanleitung

AlienTek

AlienTek T100 Bedienungsanleitung

Atten

Atten ATETOOL AT-689A Bedienungsanleitung

Surtek

Surtek 112554 Abmessungen und Installationsanleitung

Parkside

Parkside PLBS 30 A1 Bedienungsanleitung

BlackJack SolderWerks

BlackJack SolderWerks BK8000 Bedienungsanleitung

Weller

Weller WX1 Bedienungsanleitung

multicomp pro

multicomp pro MP740893 Bedienungsanleitung

jbc PHB-KA Series Bedienungsanleitung

Beliebte Lötpistole Handbücher anderer Marken