JL Audio Stealthbox SB-GM-BURB/10W3 Bedienungsanleitung

Sheet SKU#011118 Revision 5/21/01SB-GM-BURB/10W3 - JL AUDIO, Inc 2001 • Page 1

Installation Guide:

This Stealthbox is designed to mount between the front bucket seats, replacing the center console.

It is not designed for installation in vehicles with bench seats.

Please read this installation guide thoroughly before beginning the project. It will guide you step by

step through the process. This product requires professional installation skills and tools. We highly

recommend that an authorized JL AUDIO dealer performs the installation.

It is absolutely vital that the Stealthbox be properly mounted to the vehicle according to these instruc-

tions. Failure to mount the enclosure properly will result in

inferior bass performance and potential danger in the event of

a collision or sudden jolt to the vehicle.

STEP 1: Remove the storage bin from the front portion of the

center console by gently prying it out. Save this piece for later

use.

STEP 2: Remove the inner storage bin from the console by

gently prying it out. Save this piece in the event that the

original console is ever reinstalled.

STEP 3: Using a 10mm socket, remove the two bolts that

hold the front console bracket to the floor.

SB-GM-BURB/10W3 STEALTHBOX™

Fits 92-97 GM Suburbans, 88-97 GM Full-

Size Trucks, 92-97 GMC Yukons and Chevy

Tahoes (2 and 4 Door Models)

Sheet SKU#011118 Revision 5/21/01SB-GM-BURB/10W3 - JL AUDIO, Inc 2001 • Page 2

STEP 4: Slide the console forward to dislodge it from the rear

support bracket. Remove the console.

STEP 5: Using a 10mm socket, remove the two bolts that hold

the rear bracket to the floor. Remove the bracket from the ve-

hicle.

STEP 6: Place the two supplied 4" X 4" wax squares, sticky side down, in the approximate locations of the

Stealthbox mounting holes.

STEP 7: Thread both of the supplied 3/8" X 1 1/2" bolts fully into the threaded inserts in the bottom of

the Stealthbox.

STEP 8: Place the Stealthbox into its mounting location.

Be sure the Stealthbox is in the same relative position as the original factory console.

STEP 9: Press down firmly on the Stealthbox to leave impressions in the wax squares.

Sheet SKU#011118 Revision 5/21/01SB-GM-BURB/10W3 - JL AUDIO, Inc 2001 • Page 3

STEP 10: Remove the Stealthbox from the vehicle. There should be

clear impressions in the wax squares.

STEP 11: Remove the bolts from the Stealthbox.

Before drilling check under the vehicle for any loose wires, fuel lines or other hazards in the

areas where holes are to be drilled.

STEP 12: Using the impressions in the wax squares as guides, drill a 1/2" diameter hole through the floor

pan of the vehicle, using the impression in each wax square as a guide. Stop the drill immediately after

penetrating the metal.

STEP 13: Remove the wax squares from the vehicle.

STEP 14: Cut 1" diameter holes in the carpet centered on the

1/2" diameter holes you drilled in STEP 13 to allow the threaded

inserts in the Stealthbox to contact the metal floor pan.

STEP 15: Run speaker wires to the Stealthbox mounting location, as shown. Be sure the wires will not be

pinched once the Stealthbox is bolted into position.

Sheet SKU#011118 Revision 5/21/01SB-GM-BURB/10W3 - JL AUDIO, Inc 2001 • Page 4

The top of the factory center console is used as the top of the Stealthbox.

STEP 16: Remove the lid of the console by removing the 4 torx

screws holding the lid to the console. The hinges should not be

removed from the lid.

STEP 17: Remove the 8 torx screws that hold the two sections

of the console together. Separate the console.

The lower section of the console will not be used. Save this

piece in the event the original console is ever reinstalled.

STEP 18: Using four of the supplied pan head screws,attach the

four supplied "L" brackets to the top section of the console using

the factory screw holes, as shown.

STEP 19: Using the

two supplied plastic

spacers and the four

screws previously

removed in STEP 17,

attach the lid to the top

section of the console.

The spacers should be

inserted between the

lid hinge and the top of

the console.

The console top is now ready for installation onto the

Stealthbox.

Sheet SKU#011118 Revision 5/21/01SB-GM-BURB/10W3 - JL AUDIO, Inc 2001 • Page 5

STEP 20: Place the assembled top section of the console onto

the Stealthbox. Align it so that it is flush on all sides.

STEP 21: While pressing down firmly and evenly on the top of

the console, mark the location of the mounting holes for all four of

the "L" brackets with a marker or felt tip pen. The lower hole in

each bracket should be used for mounting. The upper hole in each

bracket is unused.

IT IS EXTREMELY IMPORTANT THAT YOU PRE-DRILL THESE HOLES! If the holes are not

pre-drilled the fiberglass may crack and the warranty on the Stealthbox WILL BE VOID.

STEP 22: Using a 1/16" drill bit, pre-drill the screw holes you

marked in STEP 22. The holes should be 3/4" deep.

STEP 23: Mount the top section of the console to the Stealthbox

using four of the supplied pan head screws. Do not overtighten

the screws! We recommend installing these screws by hand to

lessen the chance of stripping the fiberglass.

STEP 24: Under the front storage compartment lid, drill two holes

using a 1/16" drill bit, as shown. The holes should be 3/4" deep.

STEP 25: Using a 7/32" drill bit, drill countersink slots for the

screw heads.

Sheet SKU#011118 Revision 5/21/01SB-GM-BURB/10W3 - JL AUDIO, Inc 2001 • Page 6

10369 N. Commerce Pkwy, Miramar, Florida 33025-3921 Voice: (954) 443-1100 Fax: (954) 443-1111

Finished Installation

STEP 27: Place the supplied shallow storage tray insert into the

main storage area of the finished Stealthbox. Use Velcro®

(provided) to attach coin box to storage tray.

STEP 28: Snap the factory storage bin previously removed in

STEP 1 into the front portion of the Stealthbox.

TECH TIP: We have found that stuffing polyfill under

these bins before installation may reduce the chances of rattles at high volume levels.

STEP 29: While one person adjusts the Stealthbox from inside the vehicle, a second person should bolt the

Stealthbox into place from underneath the vehicle. See diagram below:

3/8" Bolt

Split Lock Washer

Flat Washer Car's Sheet Metal

Enclosure Wall (fiberglass) Threaded Insert

Molded into

Enclosure

Bead of Silicone Sealant

STEP 26: Using the supplied small screws, screw the front edge

of the console to the Stealthbox.

Specifications:

•Enclosure type: Sealed

•Power handling: 250 Watts Continuous

•Final Impedance: 3Ω

Parts list:

•One Stealthbox loaded with one

JL AUDIO 10W3-D6 subwoofer

•Two 3/8" X 1 1/2" Bolts

•Two Flat Washers

•Two Lock Washers

•Two 4" X 4" Wax Squares

•4 "L" Brackets

•2 Plastic Spacers

•8 Pan Head Screws

•2 Small Screws

•1 Storage Bin Insert

•1 2" strip of Velcro® hook tape

•1 2" strip of Velcro® loop tape

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere JL Audio Subwoofer Handbücher

JL Audio

JL Audio MX10IB3 Bedienungsanleitung

JL Audio

JL Audio 12TW3-D4 Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-SC-XBG1/10W1v2 Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-J-UNLTD4DR/13TW5v2 Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-GM-SLVCTR2/10W3v3 Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-GM-CLDRO/10W3v3 Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-S-LWAG/10W6v2/DG Bedienungsanleitung

JL Audio

JL Audio Fathom IWS-SYS-2 Bedienungsanleitung

JL Audio

JL Audio 8W1v3-4 Bedienungsanleitung

JL Audio

JL Audio 12W6v3-D4 Bedienungsanleitung

JL Audio

JL Audio 10W6v3 Bedienungsanleitung

JL Audio

JL Audio JL AUDIO 8W1v2-4 Bedienungsanleitung

JL Audio

JL Audio gotham v2 Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-N-PTHFNDR/10W Bedienungsanleitung

JL Audio

JL Audio 10W0v3-4 Bedienungsanleitung

JL Audio

JL Audio MX101B3-SG Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-GM-EQNX/10W1v3 Bedienungsanleitung

JL Audio

JL Audio e112 Bedienungsanleitung

JL Audio

JL Audio M10IB5-4 Bedienungsanleitung

JL Audio

JL Audio 13TW5-3 Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-GM-HUMRH2/12W6v2 Bedienungsanleitung

JL Audio

JL Audio 10W0 Bedienungsanleitung

JL Audio

JL Audio 8W1v3-4 Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-GM-ESCESV/10W1v3 Bedienungsanleitung

Beliebte Subwoofer Handbücher anderer Marken

Sony

Sony XS-AW8 Bedienungsanleitung

Sony

Sony XS-L836 Bedienungsanleitung

B&C Speakers

B&C Speakers 15 HPL 76W Bedienungsanleitung

Velodyne

Velodyne DD-18+ Bedienungsanleitung

Sonance

Sonance Cinema Series SUB 10-150 Bedienungsanleitung

Hifonics

Hifonics HW-12 Kurzanleitung

Magnat Audio

Magnat Audio ADR 130 BP Bedienungsanleitung

Blitz

Blitz BZP106 Bedienungsanleitung

Technics

Technics SB-AS500 Bedienungsanleitung

Lyngdorf

Lyngdorf BW-2 Bedienungsanleitung

Lyngdorf

Lyngdorf BW-3 Bedienungsanleitung

Pyle Pro

Pyle Pro PYLE PRO PDW15125 Bedienungsanleitung

REL Acoustics

REL Acoustics Q Series Bedienungsanleitung

L-Acoustics

L-Acoustics KIVA SB15M Kurzanleitung

Pioneer

Pioneer Elite S-W1EX Bedienungsanleitung

B&C Speakers

B&C Speakers Woofer 12 HPL 76 Bedienungsanleitung

KEF

KEF KUBE 200 Bedienungsanleitung

Yamaha

Yamaha SW500 Bedienungsanleitung