JL Audio Stealthbox SB-N-MURAN/10W1v2 Bedienungsanleitung

➔

Stealthbox®

INSTALLATION GUIDE

SB-N-MURAN/10W1v2, JL AUDIO, Inc 2006 Sheet SKU#011197 Revision1/18/2006Page 1

for the

SB-N-MURAN/10W1v2

(2003-Up Nissan Murano)

This Stealthbox is a product which

requires professional installation skills and

tools.

Please read this installation guide thor-

oughly before beginning the project. It

will guide you step by step through the

installation.Several of the steps in this

process may require two people to

accomplish.

It is absolutely vital that the enclosure

be properly mounted to the vehicle

according to these instructions. Failure

to mount the enclosure properly pres-

ents two problems: 1)The sub-bass

performance will suffer due to the

movement of the enclosure caused by

the force exerted by the woofer(s) and

2) A loose enclosure presents a serious

safety hazard in the event of a collision

or sudden deceleration.

Please enjoy your JLAudio Stealthbox

responsibly.

STEP 1:

Remove all contents,rubber flooring,

cargo shade and lower the rear seats.

STEP 2:

Open the cargo flooring and hook it

to the upper lip of the tailgate opening.

Remove the organizer tray,wooden board,

factory woofer enclosure, spare tire and the

driver’s side cargo pocket cover.

STEP 3:

a)With a Phillips® screw driver,

remove the driver’s side cargo pocket.

b)Unsnap the wiring harness that is running

from front to back,on the floor.

STEP 4:

This picture is looking from the back-

seats to the tailgate opening,showing the tail-

gate sill plate.

To remove the sill plate;Pop out the middle of

these three tabs and then pull out the outer

piece from the sill plate.

STEP 5:

With a small flat blade; pop out the

oval plastic cover of the tailgate sill plate,that

is located under the tailgate hook latch.

The sill plate now can be lifted up and

removed out of the vehicle.

STEP 6:

Look to the front left of the cargo

area for the two factory bolts that are secur-

ing a black plate to the floor.

Remove the left side bolt only.

START

HERE

Continued on Next Page ➔

www.jlaudio.com

➔

➔➔

➔➔➔

STEP 7: There is a large L-bracket that is already

mounted to the rear of the Stealthbox®.This L-

bracket needs to be unmounted, flipped around and

remounted.The picture above shows the large L-

bracket properly mounted, with the woofer facing

down.

STEP 11: To access this mounting location; enter

the vehicle via the driver’s side rear passenger door,

lift up the flooring that is laying on the second row

seat.

Place a supplied 1/4” FlatWasher onto the

8mmx35mmx1.25” Hex Bolt.

Line up the angle bracket mounting hole to the fac-

tory bolt hole. Place the bolt assembly through the

angle bracket and thread into the factory bolt hole.

Do not tightly secure.

Cont.

From

Page

Continued on Next Page ➔

➔

STEP 8: a)Place a supplied 3/8” lock washer and

3/8” flat washer onto a

3/8”-16x1-1/4” hex bolt.

Using this bolt assembly, secure the supplied

small L-bracket onto the front of the

Stealthbox®,as is in the picture above.

b)With the Stealthbox® placed into the cargo area.

Run speaker wire from the amplifier location to the

Stealthbox’s® wire terminal and secure.

STEP 12: With Stealthbox loosely mounted in the

front, use the rear L-bracket mounting hole as a drill

guide. *CAUTION*

Before drilling, make sure that you are not going to

be drilling into any gas lines, brake lines, transmission

lines, electrical wiring or anything else that might

cause a reduction in your weekly pay.Always wear

eye protection when drilling.

With the use of a 3/8” drill bit and drill. Drill out the

floor.

➔

VEHICLE'S FLOOR

LOCK WASHER

HEX HEAD BOLT

FLAT WASHER

HEX NUT

FLAT WASHER

L-BRACKET FROM STEALTHBOX

FENDER WASHER

STEP 13: With the supplied hardware, place a

3/8” FlatWasher onto the 3/8”hex bolt. Place the

bolt assembly through the angle bracket and drilled

hole, from inside the vehicle.

From the underside of the vehicle, place a

3/8” Fender Washer, 3/8” Flat Washer, 3/8” Lock

Washer and the 3/8”-16 Hex Nut onto the pro-

truding bolt. Secure tightly.

Now, tightly secure the front mounting bolt assem-

bly, from STEP11.

STEP 14: Not pictured:Place the spare tire,

hardboard and hold down wing threaded rod back

into place.

The picture above is the under side of the driver’s

side rear cargo pocket floor, that was removed in

STEP2.

Remove the three positing tabs,indicated by the

white arrows.

STEP 9: Place the Stealthbox® into position.The

speaker terminal needs to face to the front of the

vehicle.

Position the factory wiring harness around the out-

side of the front right corner of the Stealthbox®.

STEP 10: Tuck the rear of the factory harness

under the right rear corner.The harness needs to

pass between the woofer and the rear L-bracket.

*Make sure that the harness is not under the

woofer*.

SB-N-MURAN/10W1v2, JL AUDIO, Inc 2006 Sheet SKU#011197 Revision1/18/2006

Page 2

www.jlaudio.com

➔

Specifications:

Enclosure Type: Sealed

Driver Type: 10W1v2-4

Nominal Impedance: 4Ω

Cont. Power Handling: 150Watts

JLAudio recommends using a high quality amplifier such as the JLAudio e2150. The diagram below shows the recommended

crossover, infrasonic filter and equalizer settings for the e2150 when being used to power your Stealthbox®.

Included Hardware:

1) 1/4” USS FlatWasher

1) 3/8”-16x1-1/4” Hex Bolt

2) 3/8” Split LockWasher

2) #6x3/8” Philip® Head Screws

1) 3/8”-16x1-3/4” Hex Bolt

3) 3/8” FlatWasher

1) 3/8” x 1-1/4” FenderWasher

1) 2”x1-1/4”x1” 3-Hole L-Bracket

1) 3/8”-16 Hex Nut

1) 8mmx35mmx1.25” Hex Bolt

2) Round Dual Lock Fastener

10369 N. Commerce Pkwy, Miramar, Florida 33025-392 Phone: 954.443.1100 Fax: 954.443.1111

The JLAudio e2150 is a very versatile audio component. Please consult the owner’s manual for detailed information

about installing and tuning this amplifier.

➔➔➔

STEP 15: a) Lower the flooring back into position,

from STEP 2.

b) Place the driver’s side floor cargo pocket panel

back into place. Pick up the left side of the panel

and stand it up on it’s right edge, just right of the

pair of the

round dual lock fastener

.As shown in

the picture above.

c) Mark the under side of the floor panel, of the

location of the

round dual lock fastener

STEP 16: a) Flip over the side floor panel.

Measure 1-1/2” from the outside left edge to the

right.This measurement needs to line up with the

round dual lock fastener

position markings

made in STEP 15. Mark the final location.

b) With the pair of supplied round dual lock fasten-

er and the pair of #6x3/8” Phillips® screws. Mount

the round dual lock fastener to the under side of

the floor panel at the markings.

STEP 17: Snap the driver’s side rear cargo pocket

cover into place.

➔

SB-N-MURAN/10W1v2, JL AUDIO, Inc 2006 Sheet SKU#011197 Revision1/18/2006Page 3

www.jlaudio.com

Mid/High Frequency Driver Information:

CONGRATULATIONS!

INSTALL COMPLETE.

VR690-CXi

VR650-CXi

Front Location Driver Size:

6x9

Applicable JL Audio Products:

TR690-TXi &VR650-CXi

Rear Location Driver Size:

6.5”

Applicable JL Audio Products:

TR,VR & XR650-CXi

Cont.

From

Page

Difficulty Of Installation:

1-1/2”

Dieses Handbuch passt für folgende Modelle

Andere JL Audio Subwoofer Handbücher

JL Audio

JL Audio Stealthbox SB-GM-SLVCRW/10W1v2 Bedienungsanleitung

JL Audio

JL Audio 15W0v2 Bedienungsanleitung

JL Audio

JL Audio 10W0v3-4 Bedienungsanleitung

JL Audio

JL Audio Fathom IWSv2-SYS-113 Bedienungsanleitung

JL Audio

JL Audio 10WX Bedienungsanleitung

JL Audio

JL Audio M6-10IB-L Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-GM-C6CONV/8W3v3 Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-GM-CLREXT/10W3v2 Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-P-987C/13TW5v2 Bedienungs- und Wartungsanleitung

JL Audio

JL Audio 12W5-D4 Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-GM-TAHOCNSL/10W1v2 Bedienungsanleitung

JL Audio

JL Audio 8W1v2-4 Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-M-3-SPD/10W3v3 Bedienungsanleitung

JL Audio

JL Audio 12W4-4 Bedienungsanleitung

JL Audio

JL Audio SB-N-ALT/10W3v3 Bedienungsanleitung

JL Audio

JL Audio 18W6 Montageanleitung

JL Audio

JL Audio 10WXv2 Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-GM-CLDRO/10W3v3 Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-GM-BURBCNSL/10W3v2 Bedienungsanleitung

JL Audio

JL Audio 6W0-4 Bedienungsanleitung

JL Audio

JL Audio 8W1v3-4 Bedienungsanleitung

JL Audio

JL Audio JL AUDIO 8W1v2-4 Bedienungsanleitung

JL Audio

JL Audio 12W3v3-2 Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-P-CYNNE/10W6v2/BK Bedienungsanleitung

Beliebte Subwoofer Handbücher anderer Marken

Sony

Sony XS-AW8 Bedienungsanleitung

Sony

Sony XS-L836 Bedienungsanleitung

B&C Speakers

B&C Speakers 15 HPL 76W Bedienungsanleitung

Velodyne

Velodyne DD-18+ Bedienungsanleitung

Sonance

Sonance Cinema Series SUB 10-150 Bedienungsanleitung

Hifonics

Hifonics HW-12 Kurzanleitung

Magnat Audio

Magnat Audio ADR 130 BP Bedienungsanleitung

Blitz

Blitz BZP106 Bedienungsanleitung

Technics

Technics SB-AS500 Bedienungsanleitung

Lyngdorf

Lyngdorf BW-2 Bedienungsanleitung

Lyngdorf

Lyngdorf BW-3 Bedienungsanleitung

Pyle Pro

Pyle Pro PYLE PRO PDW15125 Bedienungsanleitung

REL Acoustics

REL Acoustics Q Series Bedienungsanleitung

L-Acoustics

L-Acoustics KIVA SB15M Kurzanleitung

Pioneer

Pioneer Elite S-W1EX Bedienungsanleitung

B&C Speakers

B&C Speakers Woofer 12 HPL 76 Bedienungsanleitung

KEF

KEF KUBE 200 Bedienungsanleitung

Yamaha

Yamaha SW500 Bedienungsanleitung