John Lewis Martha Sleigh cotbed Bedienungsanleitung

Martha Sleigh cotbed

Instruction manual

IMPORTANT - RETAIN FOR FUTURE

REFERENCE - PLEASE READ CAREFULLY

Thank you for purchasing this Martha Sleigh cot bed. Please read the instructions and warnings

carefully before use to ensure safe and satisfactory operation of this product.

Your child’s safety is your responsibility. If you have a query with this product or require replacement

Parts, please contact your nearest John Lewis department store.

Lay out the Parts on a soft level surface and compare to the Part/Fixings checklist on pages 2 and 3.

Do not discard any packaging until you are sure that you have all the Parts.

Ensure that your child is kept clear during assembly due to small Parts.

Recommended mattress: 70 x 140 cm

This product complies with BS EN 716 - 1: 2008 and BS 8509: 2008

Handle screw x 2

Cam nut x 1

Wood screw x 10

Drawer handle x 2

Cam pin x 1

Base x 1

End panel x 2

Side panel x 2

Drawer trim x 1

65 mm bolt x 8

Barrel nut x 4

45 mm bolt x 8

Wooden dowel x 6

Fixings

Parts

Base x 2

Drawer centre x 1

Drawer back x 1

Drawer side x 2

Drawer front x 1

You will need:

1 x 6mm Allen Key (supplied)

Flat-headed screwdriver

Cross-point screwdriver

Parts (continued)

Take one End panel (Part A) and lay it on edge as shown on a soft surface with the drawer runner

nearest the floor.

Attach one Side panel (Part B) using two 45mm bolts (Fixing 2).

Do not fully tighten the bolts at this stage.

Fixing 2

Cot assembly - step 1

Part B

Part A

2 x Fixing 3

Cot assembly - step 2

Fixing 1

Push two barrel nuts (Fixing 1) into the holes in the underside edges of the base (Part D) so that the

slot in the end is visible and is in line with the base rail. If it is not, use a flat-bladed screwdriver to

correct it.

Select the desired base position from the three available.

NOTE: the lowest position is the safest and should always be used as soon as your child is able to sit up

unaided.

Attach the base (Part D) to the assembly from step 1 using four 65mm bolts (Fixing 3).

Do not fully tighten the bolts at this stage.

Part D

2 x Fixing 4

Fixing 2

Part B

Part C

Attach the second Side panel (Part B) using two 45mm bolts (Fixing 2). Do not fully tighten bolts.

Push two Dowels (Fixing 4) into the holes in the lower leg of the End panel (Part A) and then attach

the Drawer trim (Part C) by pushing it onto the Dowels. Ensure that the curve in this part is on the

lower edge.

Cot assembly - step 3

3 Optional

positions

Push the two remaining Dowels (Fixing 4) into the holes in the end of the Drawer trim (Part C).

Insert two Barrel nuts (Fixing 1) into the holes in the underside of the Base (Part D) and ensure that

the slots are aligned correctly (See step 2)

Attach the second End panel (Part A) making sure that the Dowels in the Drawer trim are correctly

fitted in to the holes in the End panel, then insert the four 65mm bolts (Fixing 3) and four 45mm bolts

(Fixing 2) into the holes indicated above.

Stand the Cot upright and place in its final position, ensuring that the Drawer trim (Part C) is facing

away from any walls.

Fully tighten ALL bolts

Part A

Cot assembly - step 4

Fixing 1

2 x Fixing 3

Fixing 2

2 x Fixing 4

Fixing 8

Drawer assembly - step 1

Fixing 9

Push two dowels (Fixing 4) into the holes in the end of the Drawer centre (Part H).

Attach the Drawer handles (Fixing 8) to the Drawer front (Part E) with the two Handle screws (Fixing 9).

Screw the Cam pin (Fixing 5) into the centre hole in the Drawer front (Part E).

Part H

Part F

Fixing 7

Push the Drawer centre (Part H) onto the Cam pin (Fixing 5) that was fitted to the Drawer front (Part

E) in the previous stage. Ensure that the slots in both parts line up with each other.

Push the Cam nut (Fixing 6) into the large hole in the side of the Drawer centre (Part H) with the pointed

end of the slot facing the Drawer front (Part E) as shown in the diagram.To secure, use a large flat-bladed

screwdriver and turn the Cam nut (Fixing 6) clockwise approximately 1/2 a turn, until the parts are drawn

tightly together.

Attach the Drawer sides (Parts F) to the Drawer front (Part E) using fourWood screws (Fixing 7). Ensure

that the metal runners are nearest the Drawer front (Part E).

Part E

Fixing 4

Drawer assembly - step 2

Fixing 5

Fixing 7

Part F

Part E

Part H

Fixing 6

Drawer assembly - step 3

Fixing 7

Part G

Part I

Slide the two Drawer bases (Parts I) into the slots in the assembled drawer.

Fit the Drawer back (Part G) onto the rest of the drawer, ensuring that the previously fitted Base parts

fit into the slot.

Secure the Drawer back (Part G) using the remaining six Wood screws (Fixing 7).

Ensure that all fixings are fully tightened before fitting the drawer to the Cot.

Final assembly

To fit the drawer, locate the plastic rollers on the drawer in the channels of the metal drawer runners

on the cot and slide in.

If desired, the Cot can be converted to a Day bed by removing one of the side panels, or to a Toddler

bed by removing both Side panels.

NOTE: If using as either a Day bed or a Toddler bed, the base MUST be in the lowest position.

Once the panels have been removed, check the cot carefully to ensure that no fixings have come loose

and that there is no damage which may affect the strength of the cot.

In use

Care and maintenance

Your furniture may be cleaned by wiping with a damp cloth and drying with a soft clean cloth.

Do not use abrasives, bleach, alcohol or ammonia-based household polishes.

Take care when handling or moving the furniture. Careless handling may cause damage.

Safety notes - Cot mode

Furniture can be dangerous if incorrectly installed. Assembly should be carried out by a competent

person.

Keep children clear during assembly as pack contains small parts which may present a choking hazard.

Warning: Be aware of the risks of open ﬁres and other such sources of strong heat, such as electric bar

ﬁres, gas ﬁres, etc. in the near vicinity of the cot.

Warning: Do not use the cot if any part is broken, torn or missing and use only spare parts approved by

the manufacturer.

Warning: Do not leave anything in the cot or place the cot close to another product, which could

provide a foothold or present a danger of suffocation or strangulation, e.g. strings, blind/curtain cords,

etc.

Warning: Do not use more than one mattress in the cot.

The lowest base position is the safest and should be used as soon as your baby is old enough to sit up.

The thickness of the mattress chosen must not reduce the internal depth (from the top of the mattress

surface to the top of the side) to less than 500mm with the base in its lowest position or 200mm with

the base in the highest position.

The mattress should be no more than 30mm shorter or narrower than the internal length or width

of the cotbed. Suitable for use with a mattress of 1400mm in length, 700mm in width and a maximum

thickness of 100mm.

All assembly ﬁxings should always be tightened properly. Periodically check all ﬁxings to ensure none

have come loose, and that there is no risk of clothing or parts of the body becoming snagged or

trapped.

To prevent falls, when the child is able to climb out of the cot, the cot should no longer be used for that

child.

Do not allow your child to jump on the cotbed. This may result in damage to the furniture and/or

injury to your child.

JMCB 001

Safety notes - Toddler bed mode

For ages 18 months to 4 years.

Warning: Do not place this child’s bed near heat sources, windows and other furniture.

Warning: Do not use this child’s bed if any part is broken, torn or missing.

The mattress should be no more than 30mm shorter or narrower than the internal length or width

of the bed. Suitable for use with a mattress of 1400mm in length, 700mm in width and a maximum

thickness of 100mm.

Furniture can be dangerous if incorrectly installed. Assembly should be carried out by a competent

person.

All assembly ﬁxings should always be tightened properly. Periodically check all ﬁxings to ensure none

have come loose, and that there is no risk of clothing or parts of the body becoming snagged or

trapped.

Do not allow your child to jump on the bed. This may result in damage to the furniture and/or injury

to your child.

Children are likely to play, bounce, jump & climb on beds, therefore the child’s bed should not be placed

too close to other furniture or windows, and should be placed either tight to any wall or have a gap of

300mm between the wall and the side of the bed.

Keep children clear during assembly as pack contains small parts which may present a choking hazard.

Retain this information leaﬂet for future reference.

John Lewis Partnership

171 Victoria Street

London

SW1E 5NN

www.johnlewis.com

Inhaltsverzeichnis

Andere John Lewis Inneneinrichtung Handbücher

John Lewis

John Lewis OXFORD 83501 Bedienungsanleitung

John Lewis

John Lewis Morgan Guest Bedstead 800/61601 Bedienungsanleitung

John Lewis

John Lewis Mixit Bedienungsanleitung

John Lewis

John Lewis Match 81610115 Bedienungsanleitung

John Lewis

John Lewis Milan Bed 803/45901 Bedienungsanleitung

John Lewis

John Lewis St. Ives Series Bedienungsanleitung

John Lewis

John Lewis Morgan 803/16409 Bedienungsanleitung

John Lewis

John Lewis CUBE 816/25502 Bedienungsanleitung

John Lewis

John Lewis SBSKITC Bedienungsanleitung

John Lewis

John Lewis 803/15701 Bedienungsanleitung

John Lewis

John Lewis Genoa 2 Drawer Storage 810/84001 Bedienungsanleitung

John Lewis

John Lewis 82015322 Bedienungsanleitung

John Lewis

John Lewis Emily Storage Bed Bedienungsanleitung

John Lewis

John Lewis 86203502 Bedienungsanleitung

John Lewis

John Lewis Amy White Chair Bedienungsanleitung

John Lewis

John Lewis Duhrer 836 03703 Bedienungsanleitung

John Lewis

John Lewis 41392441 Bedienungsanleitung

John Lewis

John Lewis Ivybridge Le Bedstead 80344001 Bedienungsanleitung

John Lewis

John Lewis MIRA 836 23502 Bedienungsanleitung

John Lewis

John Lewis Devon 820/81602 Bedienungsanleitung

John Lewis

John Lewis Grace Bed Bedienungsanleitung

John Lewis

John Lewis Rouen Bedienungsanleitung

John Lewis

John Lewis FLAT-SCREEN TELEVISION STAND JLC95/3-B/W-09 Bedienungsanleitung

John Lewis

John Lewis FELT MAGAZINE RACK 57020306 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung