Johnson Controls SEN-600-1 Bedienungsanleitung

Installation Instructions

Issue Date September 23, 2003

SEN-600-1 and SEN-600-4 Remote Indoor

Temperature Sensors

Application Installation

Dimensions

The SEN-600-1 and SEN-600-4 remote sensors are

designed to allow remote indoor temperature sensing

in applications with the T600 Series programmable

and non-programmable thermostats and the TEC2100

Metasys® system N2 networked thermostats. The

SEN-600-1 and SEN-600-4 contain an integral sensor

and circuitry to interface with the T600 and TEC2100

thermostats. Additionally, the SEN-600-4 has an

override button and Light-Emitting Diode (LED)

indicator to enable and indicate occupancy override

from the remote sensor. Up to three remote sensors

can be wired together for averaging.

125

4.94

3.38

1.13

Note: The SEN-600-4 remote indoor sensor is only

intended for use with programmable T600 Series

thermostats. Additionally, if the SEN-600-4 is used

with a T600 non-programmable thermostat, the LED

does not light up to indicate occupancy status.

Figure 1: Sensor Dimensions (mm/in.)

Mounting To install the sensor:

Prior to installing the sensor, install the T600 or

TEC2100 thermostat following the installation

instructions provided with the thermostat.

1. Remove the security screw on the bottom of the

sensor cover using a Phillips-head screwdriver.

Open the thermostat by pulling on the bottom side

of the sensor cover (see Figure 2).

Location Considerations

2. Unlock the Printed Circuit Board (PCB) by

carefully pressing the locking tabs to the right.

Open the sensor’s PCB to the left (see Figure 3).

Locate the sensors as follows:

• on a partitioning interior wall, and approximately

1.5 m (5 ft) above the floor in a location of average

temperature 3. Pull out approximately 152 mm (6 in.) of wires

from the wall and insert the cable through the hole

in the base.

• away from direct sunlight, radiant heat, outside

walls, behind doors, air discharge grills, stairwells,

or outside doors 4. Align the base on the wall, and using the base as

a template, mark the location of the two mounting

holes on the wall. Confirm the sensor base is

installed with the proper side up.

• away from steam or water pipes, warm air stacks,

unheated/uncooled areas, or sources of electrical

interference 5. Use the supplied anchors and screws for mounting

on drywall or plaster. Drill two 4.7 mm (3/16 in.)

holes at the marked locations and tap nylon

anchors flush to wall surface (see Figure 4).

6. Position base on the wall, insert screws through

mounting base, and fasten into wall anchors. Do

not overtighten screws.

Part No. 24-9954-7, Rev. — www.johnsoncontrols.com

7. Swing the sensor’s PCB back to the right to close.

Gently press on the PCB to secure the locking tab.

Figure 2: Removing the Sensor Cover

PCB

Locking Tab

Figure 3: Opening the Sensor PCB

Figure 4: Mounting the Sensor Base

Wiring

CAUTION: Risk of Electrical Shock.

Disconnect power supply before making electrical

connections to avoid electrical shock.

Note:

Keep sensor conductors as short as possible

to minimize temperature error. If necessary, the indoor

temperature displayed at the thermostat can be

adjusted (see the appropriate T600 or TEC2100

Installation Instructions).

To complete wiring for the sensor:

1. Connect wires between the T600 or TEC2100

thermostat and the SEN-600-1 or SEN-600-4

sensors according to the appropriate wiring

diagram (see Figure 5).

2. Set the switch on the PCB in the remote indoor

sensor to the correct positions (see Table 1 for

switch positions).

3. Reattach the sensor cover to the installed base

(top side first) and install the security screw on the

bottom.

4. Verify that the sensor is functioning by checking

the temperature display on the T600 or TEC2100

thermostat. If using the SEN-600-4 remote sensor,

verify the functionality of the override button and

occupancy status LED.

If using the SEN-600-4, the digital input on the

thermostat to which the D1 terminal on the sensor is

connected must be configured for remote override

(RemOVR). See the T600 Installation Instructions for

details on configuring the digital input.

CAUTION: Risk of Electrical Shock.

Do not apply power to the system before checking

all wiring connections. Short circuited or improperly

connected wires may result in permanent damage to

the equipment.

Table 1: Switch Positions for Single or Multiple

Sensor Installations

Number of Sensors Switch 1 Switch 2

1 Sensor On On

2 Sensor Off On

3 Sensor Off Off

2SEN-600-1 and SEN-600-4 Remote Indoor Temperature Sensors Installation Instructions

SEN-600-1 and SEN-600-4 Remote Indoor Temperature Sensors Installation Instructions 3

Scom

AUX

Scom

D1D2

Scom

AUX

T600 SEN-600-4 SEN-600-4

Scom

D1D2

Scom

T600 or TEC2100

SEN-600-1 SEN-600-1

Scom

AUX

Scom

D1D2

Scom

SEN-600-1

SEN-600-4

T600

This is a wiring example of two remote room sensors for averaging applications (S1=Off, S2=On).

Note: When wiring the SEN-600-4 remote indoor sensor to

a non-programmable model of the T600, the AUX terminal

on the SEN-600-4 is not used. Additionally, when using the

SEN-600-4 remote indoor sensor with a non-programmable

model of the T600, the LED will not light to indicate

occupancy status.

This is a wiring example of a single remote room sensor (S1=On, S2=On).

Scom

AUX

Scom

D1D2

T600 SEN-600-4

Scom

D1D2

T600 or TEC2100

SEN-600-1

This is a wiring example of three remote room sensors for averaging applications (S1=Off, S2=Off).

T600

Scom

D1D2

Scom

AUX

Scom

SEN-600-1

SEN-600-4

Scom

SEN-600-1

Scom

AUX

Scom

AUX

SEN-600-4 SEN-600-4

Scom

SEN-600-1

Scom

D1D2

T600

T600 or TEC2100

Scom

SEN-600-1SEN-600-1

Scom

SEN-600-1

Figure 5:Wiring Diagrams

4SEN-600-1 and SEN-600-4 Remote Indoor Temperature Sensors Installation Instructions

Troubleshooting

Table 2: Troubleshooting

Symptom Possible Cause Corrective Action

Remote sensor is not correctly

connected.

Check wiring connections at the

thermostat terminal blocks and

between the thermostat and the

remote sensor.

Temperature displayed at the T600

or TEC2100 does not correlate with

the temperature at the remote

sensor.

T600, TEC2100, or remote sensor has

failed.

Short the appropriate sensor terminals

at the thermostat. The display should

indicate 50°C (122°F). If the reading is

not 50°C (122°F), replace the

thermostat. If the reading is 50°C

(122°F), check the resistance across

the sensor with the wires removed

from the thermostat. The resistance

should be 10,000 ohms at 25°C

(77°F). If the resistance is not correct,

replace the sensor.

SEN-600-4 is incorrectly wired to the

thermostat.

Check wiring connections with the

corresponding digital input at the

thermostat, at the D1 terminal on the

remote sensor, and between the

thermostat and remote sensor.

Override button on SEN-600-4

remote sensor is not functional.

The appropriate digital input on the

thermostat is not configured to remote

override (RemOVR).

Configure the appropriate digital input

at the thermostat for remote override

(RemOVR). See the T600 Installation

Instructions for details.

SEN-600-4 is incorrectly wired to the

thermostat.

Check wiring connections at the

auxiliary output at the programmable

T600 thermostat, at the AUX terminal

on the remote sensor, and between

the thermostat and remote sensor.

The auxiliary output is not properly

configured at the T600 programmable

thermostat.

Configure the auxiliary output at the

T600 programmable thermostat for

Normally Open (N.O.). See the T600

Installation Instructions for details.

Remote LED is not functional on the

SEN-600-4 remote sensor.

The T600 Series thermostat to which

the SEN-600-4 is connected is not a

programmable model.

The LED does not indicate occupancy

status on non-programmable T600

models (there is no auxiliary contact at

the thermostat). Replace the T600 with

a programmable model.

SEN-600-1 and SEN-600-4 Remote Indoor Temperature Sensors Installation Instructions 5

Technical Specifications

Product SEN-600-1 and SEN-600-4 Remote Indoor Temperature Sensor

Power Requirements Supplied by the T600 or TEC2100 Thermostat

Sensor Accuracy ±0.5 Cº from 0 to 70ºC; ±0.9 Fº from 32 to 158ºF

Sensor Ambient Operating

Conditions 0 to 50ºC (32 to 122ºF); 0 to 95% RH noncondensing

Sensor Ambient Storage

Conditions -30 to 50ºC (-22 to 122ºF); 0 to 95% RH noncondensing

Dimensions (H x W x D) 125 x 86 x 29 mm (4.94 x 3.38 x 1.13 in.)

Shipping Weight 0.34 kg (0.75 lb)

The performance specifications are nominal and conform to acceptable industry standards. For application at conditions beyond these

specifications, consult the local Johnson Controls office. Johnson Controls, Inc. shall not be liable for damages resulting from misapplication or

misuse of its products.

Controls Group

507 E. Michigan Street

P.O. Box 423 Published in U.S.A.

Milwaukee, WI 53201 www.johnsoncontrols.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Johnson Controls Zubehör Handbücher

Johnson Controls

Johnson Controls NS Series Bedienungsanleitung

Johnson Controls

Johnson Controls NS8000 Series Bedienungsanleitung

Johnson Controls

Johnson Controls NS Series Bedienungsanleitung

Johnson Controls

Johnson Controls NS Series Bedienungsanleitung

Johnson Controls

Johnson Controls NS Series Bedienungsanleitung

Johnson Controls

Johnson Controls WRZ-TTB0000-5 Bedienungsanleitung

Johnson Controls

Johnson Controls NS-AHN700 Series Bedienungsanleitung

Johnson Controls

Johnson Controls NS Series Bedienungsanleitung

Johnson Controls

Johnson Controls NS-AP Series Bedienungsanleitung

Johnson Controls

Johnson Controls NS Series Bedienungsanleitung

Johnson Controls

Johnson Controls TE-7800 Series Bedienungsanleitung

Johnson Controls

Johnson Controls TE-6300F Series Bedienungsanleitung

Johnson Controls

Johnson Controls B401BH Bedienungsanleitung

Johnson Controls

Johnson Controls WRZ Series Bedienungsanleitung

Johnson Controls

Johnson Controls GS3000 Bedienungsanleitung

Johnson Controls

Johnson Controls THM-R2A Bedienungsanleitung

Johnson Controls

Johnson Controls GS3000 Bedienungsanleitung

Johnson Controls

Johnson Controls NS8000 Series Bedienungsanleitung

Johnson Controls

Johnson Controls WRZ Series Bedienungsanleitung

Johnson Controls

Johnson Controls NS8000 Series Bedienungsanleitung

Johnson Controls

Johnson Controls 2951J-COPTIR Bedienungsanleitung

Johnson Controls

Johnson Controls TMZ1600 Bedienungsanleitung

Johnson Controls

Johnson Controls TEC-6-PIR Bedienungsanleitung

Johnson Controls

Johnson Controls NS Series Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung