Juniper JCS 1200 Bedienungsanleitung

Replacing a JCS 1200 Management Module or Module Filler

Topics include:

■Removing a JCS 1200 Management Module or Module Filler on page 1

■Installing a JCS 1200 Management Module or Module Filler on page 2

Removing a JCS 1200 Management Module or Module Filler

Figure 1 on page 1 shows how to remove and install a management module.

Figure 1: Removing and Installing a JCS 1200 Management Module

When you remove a management module, keep in mind the following:

■These instructions assume that the JCS 1200 platform is connected to power.

■If you are replacing the only management module in the JCS 1200 platform and

the management module is functioning, save the configuration file before you

proceed. For information about saving and restoring a configuration file, see the

JUNOS Protected System Domain Configuration Guide.

■If you have just installed a second management module in the JCS 1200 platform,

do not remove the first (primary) management module for up to 45 minutes;

the second (redundant) management module needs the time to receive initial

status information and firmware from the management module.

To remove a management module or module filler (see Figure 1 on page 1):

1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and

connect the strap to one of the ESD points on the chassis.

2. Pull the management module release handle to the open position. The module

moves out of the bay approximately 0.25 in. (0.6 cm).

3. Slide the management module out of the bay.

Replacing a JCS 1200 Management Module or Module Filler ■1

Installing a JCS 1200 Management Module or Module Filler

Figure 2 on page 2 shows how to remove and install a management module.

Figure 2: Removing and Installing a JCS 1200 Management Module

To install a management module or module filler (see Figure 2 on page 2):

1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and

connect the strap to one of the ESD points on the chassis.

2. Remove the management module filler, if one is installed.

3. Remove the management module interposer filler tray, if one is installed.

4. Install the management module interposer, if it is not already installed.

5. Make sure that the release handle on the management module is in the open

position.

6. Slide the management module into the management module bay until it stops.

7. Push the management module release handle to the closed position.

8. Connect any cables to the management module.

9. If the JCS 1200 platform is connected to power, make sure that the OK LED on

the management module is lit. If the management module is redundant, wait at

least 45 minutes for the modules to copy the configuration data before you make

any changes to the management module configuration.

Related Topics ■Preventing Electrostatic Discharge Damage to the JCS 1200 Platform

■JCS 1200 Management Module Description

■Replacing a JCS 1200 Management Module Filler Tray

■Locating the JCS 1200 Management Module Serial Number

2■Installing a JCS 1200 Management Module or Module Filler

Andere Handbücher für JCS 1200

6

Inhaltsverzeichnis

Andere Juniper Netzwerk-Router Handbücher

Juniper

Juniper PTX10001 Bedienungsanleitung

Juniper

Juniper M7i Montageanleitung

Juniper

Juniper ACX710 Bedienungsanleitung

Juniper

Juniper M320 Montageanleitung

Juniper

Juniper MX150 Bedienungsanleitung

Juniper

Juniper ACX5448-D Montageanleitung

Juniper

Juniper MX240 Montageanleitung

Juniper

Juniper QFX5100 Montageanleitung

Juniper

Juniper T Series Bedienungsanleitung

Juniper

Juniper EX9200 Series Technisches Datenblatt

Juniper

Juniper LN2600 Bedienungsanleitung

Juniper

Juniper MX2020 Montageanleitung

Juniper

Juniper M10i Montageanleitung

Juniper

Juniper ERX-310 Bedienungsanleitung

Juniper

Juniper ACX1000 Montageanleitung

Juniper

Juniper M120 Bedienungsanleitung

Juniper

Juniper EX4600 Bedienungsanleitung

Juniper

Juniper EX9200 Series Technisches Datenblatt

Juniper

Juniper ACX4000 Bedienungsanleitung

Juniper

Juniper J2300 Bedienungsanleitung

Juniper

Juniper CTP2000 Series Bedienerhandbuch

Juniper

Juniper MX240 Montageanleitung

Juniper

Juniper ACX500 Bedienungsanleitung

Juniper

Juniper MX10003 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise