JVC KD-S570 Bedienungsanleitung

INSTRUCTIONS

MANUAL DE INSTRUCCIONES

MANUEL D’INSTRUCTIONS

GET0003-001C

[J]

For customer Use:

Enter below the Model No. and

Serial No. which are located on

the top or bottom of the cabinet.

Retainthisinformationforfuture

reference.

Model No.

Serial No.

For installation and connections, refer to the separate manual.

Para la instalación y las conexiones, refiérase al manual separado.

Pour l’installation et les raccordements, se référer au manuel séparé.

COMPACT

DIGITAL AUDIO

KD-S620

RECEPTEUR CD KD-S620/S576/S570

RECEPTOR CON CD KD-S620/S576/S570

CD RECEIVER KD-S620/S576/S570

ENGLISH

ESPAÑOL

FRANÇAIS

KD-S576

KD-S570

KD-S576

KD-S570

CoverKD-S620.S576.S570(J)F 26/04/2001, 9:24 AM3

ENGLISH

INFORMATION (For USA)

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection

against harmful interference in a residential installation.This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interferencewillnotoccurinaparticularinstallation.Ifthis equipment does cause harmful interference

to radio or television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

– Consult the dealer or an experienced radio/TV technician for help.

IMPORTANT FOR LASER PRODUCTS

Precautions:

1. CLASS 1 LASER PRODUCT

2. DANGER: Invisible laser radiation when open and interlock failed or defeated. Avoid direct

exposure to beam.

3. CAUTION: Do not open the top cover.There are no user-serviceable parts inside. Leave all

servicing to qualified service personnel.

4. CAUTION: This CD player uses invisible laser radiation, however, is equipped with safety switches

to prevent radiation emission when unloading CDs. It is dangerous to defeat the safety switches.

5. CAUTION: Use of controls, adjustments or performance of procedures other than those specified

herein may result in hazardous radiation exposure.

(Standby/On/ATT)

How to reset your unit

Press and hold both the SEL (Select) and

(Standby/On/ATT) buttons at the same time for several

seconds.

This will reset the built-in microcomputer.

NOTES:

Your preset adjustments — such as preset channels or sound

adjustments — will also be erased.

If a CD is in the unit, it will eject when you reset the unit. Pay

attention not to drop the CD. SEL (Select)

EN02-03KD-S620.S576.S570(J)F 26/04/2001, 9:25 AM2

ENGLISH

CONTENTS

Thank you for purchasing a JVC product. Please read all instructions carefully before operation,

to ensure your complete understanding and to obtain the best possible performance from the unit.

How to reset your unit.................................. 2

LOCATION OF THE BUTTONS ...............4

Control panel ............................................... 4

Remote controller (only for KD-S620).......... 5

Preparing the remote controller

(only for KD-S620) ................................... 6

BASIC OPERATIONS ..........................7

Turning on the power ................................... 7

RADIO BASIC OPERATIONS .................8

Listening to the radio ................................... 8

Storing station in memory ............................ 9

Tuning into a preset station........................ 10

Other convenient tuner functions ............... 10

CD OPERATIONS ............................ 11

Playing a CD.............................................. 11

Locating a track or a particular portion

on a CD.................................................. 12

Selecting CD playback modes................... 12

Prohibiting CD ejection .............................. 13

SOUND ADJUSTMENTS.................... 14

Adjusting the sound ................................... 14

Turning on/off the loudness function ............. 14

Using the Sound Control Memory (SCM) .. 15

Storing your own sound adjustments......... 16

OTHER MAIN FUNCTIONS ................. 17

Setting the clock ........................................ 17

To cancel advanced SCM .......................... 17

Selecting the level display.......................... 18

Detaching the control panel ....................... 19

MAINTENANCE .............................. 20

Handling CDs ............................................ 20

TROUBLESHOOTING ....................... 21

SPECIFICATIONS............................ 22

BEFORE USE

For safety....

• Do not raise the volume level too much, as this

will block outside sounds, making driving

dangerous.

• Stop the car before performing any complicated

operations.

Temperature inside the car....

If you have parked the car for a long time in hot

or cold weather, wait until the temperature in the

car becomes normal before operating the unit.

EN02-03KD-S620.S576.S570(J)F 26/04/2001, 9:25 AM3

ENGLISH

LOCATION OF THE BUTTONS

1(standby/on/attenuator) button

2+/– button

3LOUD button

4MO (monaural) button

RND (random) button

5Display window

6Remote sensor (only for KD-S620)

70(eject) button

8CD button

9FM button

pAM button

qSEL (select) button

w4/ ¢buttons

• Also functions as SSM buttons when

pressed together.

eNumber buttons

rDISP (display) button

tRPT (repeat) button

SCAN button

ySCM (sound control memory) button

u(control panel release) button

Display window

iVolume (or audio) level indicator

Equalization Pattern indicator

oTuner reception indicators

STEREO, MONO

;RND (random) indicator

aRPT (repeat) indicator

s"SCM" indicator

dLOUD indicator

fSound mode indicators

BEAT, SOFT, POP

gCD indicator

hBand indicators

FM1, FM2, FM3

jMain display

kCD IN indicator

Display window

12 34 5 6

789p

qwert y u

;a sdf

Control panel

EN04-06KD-S620.S576.S570(J)F 26/04/2001, 9:25 AM4

ENGLISH

RM-RK31

Remote controller

(only for KD-S620)

This section is only for KD-S620.

1• Turns on the unit if pressed when the unit is

turned off.

• Turns off the unit if pressed and held until

“SEEYOU” appears on the display.

• Drops the volume level in a moment if

pressed briefly.

Press again to resume the volume.

2• Functionsas the BAND buttonwhile listening

to the FM broadcast.

Each time you press the button, the band

changes.

• Does not function as the PROG/DISC +

button.

3• Functions as the PRESET button while

listening to the radio.

Each time you press the button, the preset

station number increases, and the selected

station is tuned into.

• Does not function as the DISC – button.

4Functions the same as the + and – buttons on

the main unit.

Note:

These buttons cannot be used for the clock

(CLOCK H, CLOCK M), SCM LINK and

LEVEL (see pages 17 and 18).

5Selects the sound mode.

Each time you press the button, the mode

changes.

6Selects the source.

Each time you press the button, the source

changes.

7• Searchesstations while listening to theradio.

• Fast -forwardsor reversesthe trackifpressed

and held while listening to a CD.

• Skips to the beginning of the next tracks or

goes back to the beginning of the current (or

previous tracks) if pressed briefly while

listening to a CD.

EN04-06KD-S620.S576.S570(J)F 26/04/2001, 9:25 AM5

ENGLISH

Remote sensor

(back side)

WARNING:

• Store the batteries in a place which children

cannot reach.

If a child accidentally swallows the battery,

consult a doctor immediately.

• Do not recharge, short, disassemble or heat the

batteries or dispose it in a fire.

Doing any of these things may cause the

batteries to give off heat, crack or start a fire.

• Do not leave the batteries with other metallic

materials.

Doing this may cause the batteries to give off

heat, crack or start a fire.

• When throwing away or saving the batteries,

wrap it in tape and insulate; otherwise, the

batteriesmay start to give off heat, crackor start

a fire.

• Do not poke the batteries with tweezers or

similar tools.

Doing this may cause the batteries to give off

heat, crack or start a fire.

Return the battery holder.

Insertagain the battery holder pushing it until

you hear a clicking sound.

Preparingtheremotecontroller

This section is ONLY FOR KD-S620.

Before using the remote controller:

• Aim the remote controller directly at the remote

sensor on the main unit. Make sure there is no

obstacle in between.

• Do not expose the remote sensor to strong light

(direct sunlight or artificial lighting).

(back side) 1) 2)

Installing the battery

When the controllable range or effectiveness of

the remote controller decreases, replace the

battery.

Remove the battery holder.

1) Push out in the direction indicated by the

arrow using a ball point pen or a similar

tool.

2) Remove the battery holder.

Place the battery.

Slide the battery into the holder with the +

sidefacing upwards so thatthebattery is fixed

in the holder.

Lithium coin battery

(product number:

CR2025)

EN04-06KD-S620.S576.S570(J)F 26/04/2001, 9:25 AM6

ENGLISH

Adjust the sound as you want (see

page 14).

To drop the volume in a moment

Press briefly while listening to any

source.“ATT” starts flashing on the display, and

the volume level will drop in a moment.

To resume the previous volume level, press the

button briefly again.

To turn off the power

Press and hold until "SEEYOU"

appears on the display.

Note:

When you use this unit for the first time, set the built-

in clock correctly, see page 17

Turning on the power

Turn on the power.

Note on One-Touch Operation:

When you select a source in step 2 below, the

power automatically comes on. You do not have

to press this button to turn on the power.

Select the source.

Adjust the volume.

BASIC OPERATIONS

C D

A M

F M

Volume or audio level indicator

(see page 18)

Volume level appears

To increase the volume.

To decrease the volume.

To operate the tuner (FM or AM),

see pages 8 – 10.

To operate the CD,

see pages 11 – 13.

CAUTION on volume setting

CDs produce very little noise compared with other

sources. If the volume level is adjusted for the tuner,

for example, the speakers may be damaged by the

sudden increase in the output level. Therefore, lower

the volume before playing a disc and adjust it as

required during playback.

EN07-07KD-S620.S576.S570(J)F 26/04/2001, 9:26 AM7

ENGLISH

RADIO BASIC OPERATIONS

Listening to the radio

You can use either automatic searching or manual

searching to tune into a particular station.

Searching a station automatically:

Auto search

Select the band (FM 1 – 3, AM).

Note:

This receiver has three FM bands (FM1, FM2,

FM3). You can use any one of them to listen to an

FM broadcast.

Start searching a station.

When a station is received, searching stops.

A M

F M

FM1 FM2

FM3

selected band appears

Volume or audio level (see page 18) indicator

Press ¢to search

stations of higher

frequencies.

Press 4to search

stations of lower

frequencies.

To stop searching before a station is received,

press the same button you have pressed for

searching.

Searching a station manually:

Manual search

Select the band (FM 1 – 3, AM).

Note:

This receiver has three FM bands (FM1, FM2,

FM3). You can use any one of them to listen to an

FM broadcast.

Press and hold 4or ¢ until

“M” starts flashing on the display.

A M

F M

FM1 FM2

FM3

selected band appears

EN08-10KD-S620.S576.S570(J)F 26/04/2001, 9:34 AM8

ENGLISH

Tune into a station you want while“M”

is flashing.

• If you release your finger from the button, the

manual mode will automatically turn off after 5

seconds.

• If you hold down the button, the frequency keeps

changing until you release the button.

When an FM stereo broadcast is hard to

receive:

Press MO/RND (monaural/random) while listening

to an FM stereo broadcast.

• Eachtime youpress the button, the MO indicator

lights up and goes off alternately.

When the MO indicator is lit on the display, the

sound you hear becomes monaural but the

reception will be improved (the ST indicator goes

off).

Storing stations in memory

You can use one of the following two methods to

store broadcasting stations in memory.

• Automatic preset of FM stations: SSM (Strong-

station Sequential Memory)

• Manual preset of both FM and AM stations

FM station automatic preset: SSM

Youcan preset6localFMstationsin each FM band

(FM1, FM2 and FM3).

Select the band (FM1 – 3) you want

to store FM stations into.

• Each time you press the button, the FM

band changes as follows:

Press and hold both buttons for

more than 2 seconds.

Local FM stations with the strongest signals are

searched and stored automatically in the band

number you have selected (FM1, FM2 or FM3.)

These stations are preset in the number buttons –

No.1(lowest frequency)to No.6(highestfrequency).

When automatic preset is over, the station stored

in number button 1 will be automatically tuned in.

A M

F M

FM1 FM2

FM3

Press ¢to search

stations of higher

frequencies.

Press 4to search

stations of lower

frequencies.

MO/RND

“SSM” appears, then disappears when automatic

preset is over.

Lights up when receiving an

FM broadcast in stereo.

EN08-10KD-S620.S576.S570(J)F 26/04/2001, 9:34 AM9

ENGLISH

Manual preset

Youcanpresetup to 6 stationsineach band (FM1,

FM2, FM3 and AM) manually.

Ex: Storing an FM station of 88.3 MHz into the

preset number 1 of the FM1 band.

Select the band (FM1 – 3) you want

to store FM stations into (in this

example, FM1).

• Each time you press the button, the FM

band changes as follows:

Tune into a station of 88.3 MHz.

Press and hold the number button (in

this example, 1) for more than 2

seconds.

Repeat the above procedure to store

other stations into other preset

numbers.

Other convenient tuner

functions

Scanning broadcast station

When you press RPT/SCAN while listening to the

radio,stationscanningstarts.Eachtimeabroadcast

is tuned in, scanning stops for about 5 seconds

(tunedfrequency number flashesonthe display), and

you can check what program is now being

broadcasted.

If you want to listen to that program, press the same

button again to stop scanning.

Press ¢totune

stations of higher

frequencies.

Press4totune

stations of lower

frequencies.

”P1” flashes for a few seconds.

Notes:

• Apreviously preset station is erased when a new station

is stored in the same preset number.

• Preset stations are erased whent the power supply to

the memory circuit is interrupted (for example, during

battery replacement). If this occurs, preset the stations

again.

Tuning into a preset station

You can easily tune into a preset station.

Remember that you must store stations first. If you

have not stored them yet, see ”Storing stations in

memory” on page 9 and 10.

Select the band (FM1 – 3, AM).

Select the number (1 – 6) for the preset

station you want.

A M

F M

FM1 FM2

FM3

7 8 9 10 11 12

RPT

SCAN

A M

F M

FM1 FM2

FM3

EN08-10KD-S620.S576.S570(J)F 26/04/2001, 9:34 AM10

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere JVC Autoempfänger Handbücher

JVC

JVC KD-R901 Bedienungsanleitung

JVC

JVC KD-DV6101 Bedienungsanleitung

JVC

JVC KW-V40BT Bedienungsanleitung

JVC

JVC KD-ADV49 - DVD Player With LCD monitor Bedienungsanleitung

JVC

JVC KD-S895 Bedienungsanleitung

JVC

JVC KD-SV3205 Bedienungsanleitung

JVC

JVC KD-SX8250 Bedienungsanleitung

JVC

JVC KD-S577 Bedienungsanleitung

JVC

JVC KD-R421 Bedienungsanleitung

JVC

JVC KW-XC550J Bedienungsanleitung

JVC

JVC KD-G341 Bedienungsanleitung

JVC

JVC KD-G317 Bedienungsanleitung

JVC

JVC GET0564-006A Bedienungsanleitung

JVC

JVC KD-SR72 Bedienungsanleitung

JVC

JVC KD-S9R Bedienungsanleitung

JVC

JVC LVT1134-001A Bedienungsanleitung

JVC

JVC KD-R890BT Bedienungsanleitung

JVC

JVC KD-S70R Bedienungsanleitung

JVC

JVC KD-HDR70 Bedienungsanleitung

JVC

JVC KW-XC899 Bedienungsanleitung

JVC

JVC KD-T706BT Bedienungsanleitung

JVC

JVC KD-DV4200 - DVD Player With Radio Bedienungsanleitung

JVC

JVC KD-R690S Bedienungsanleitung

JVC

JVC EXAD KD-LHX501 Leitfaden

Beliebte Autoempfänger Handbücher anderer Marken

Motorola

Motorola VWA63 Bedienungsanleitung

Nextar

Nextar D3201 Bedienungsanleitung

Alpine

Alpine CDE-163BT Bedienungsanleitung

Pioneer

Pioneer DEH-P645R Bedienungsanleitung

Axxera

Axxera XDMA7600 Betriebsanleitung

XM OnyX Bedienungsanleitung

Sound Storm

Sound Storm STM93R Bedienungsanleitung

Soundstream

Soundstream VIR-5000 Bedienungsanleitung

Avson

Avson MKT Platform Bedienungsanleitung

Sony

Sony MEX-1HD - Audio Library System Bedienungsanleitung

Pioneer

Pioneer DVH-P500UB Bedienungsanleitung

Blaupunkt

Blaupunkt SANTIAGO CR 87 Bedienungsanleitung

Sony

Sony CDX-4160 - Cd Receiver Bedienungsanleitung

XFIRE AUDIO

XFIRE AUDIO BMW42S Bedienungsanleitung

VDO

VDO CD 2253 Bedienungsanleitung

Volvo

Volvo 13 84 580 Bedienungsanleitung

ZENEC

ZENEC ZE-160DVD Bedienungsanleitung

Medion

Medion Car Audio Bedienungsanleitung