Kamstrup 382 Bedienungsanleitung

www.kamstrup.com

Manual

Kamstrup 382

Operating instructions

Connect the meter in accordance with the installation diagram on the meter’s type label.

Depending on the configuration a fixed value will be displayed, or the display will

change between selected indications every 10 seconds.

It is possible to change the display reading manually by activating the push button on

the meter. The available readings will depend on the meter’s configuration.

Security and installation guidelines

The meter is only to be used for measuring electrical energy and shall operate within the

specified values only.

The meter must be disconnected when working on it. It can be highly dangerous to touch

the meter parts when the meter is switched on.

Therefore, the relevant security fuse must be removed and kept in a place where it cannot

be inserted by unauthorized persons.

Current local standards, guidelines, regulations and instruction must be observed. Only

authorized personnel is permitted to install electricity meters.

Meters for direct connection must be protected against short circuit by a security fuse in

accordance with the maximum current stated on the meter.

The meter constant LED blinks proportionally to the consumed active energy.

Only authorized personnel must break the utility sealing.

Utility seals

LCD-display

Optical interface

LED (meter constant)

Push button

Type label

LED breaker status

(only meters with

internal breaker)

LCD display

The phase indications (L1, L2 and L3) have various functions. They indicate the two

situations described below.

From reset (voltage cut-off) of meter and 4 hours ahead:

Indications L1, L2, L3 Indicate

On Voltage is above minimum limit (160V), and load is above

minimum limit (2.3W).

Off Voltage is below minimum limit (160V).

Flashing Voltage is above minimum limit (160V), and load is below

minimum limit (2.3W).

After 4 hours’ operation:

Indications L1, L2, L3 Indicate

On Voltage is above minimum limit (160V).

Off Voltage is below minimum limit (160V).

If the load exceeds the minimum limit and the meter is configured with this reading,

consumption will be indicated via the quadrant reading.

The meter’s LED can be used provided that the quadrant indicator is not selected.

The measured unit is displayed in the right side of the display.

Tariff indicating active tariff.

Terminals

Multi core 7 core Massive /

terminals

Size: 1,5 – 25 mm2

1,5 – 35 mm2

Screw: Pz 2

Torch: 2,5 – 3 Nm

Brass terminal

35 mm2≥10 mm2≥10 mm2≥4 mm2

Steel terminal

35 mm2≥6 mm2≥6 mm2≥1,5 mm2

Steel terminal

25 mm2≥6 mm2≥6 mm2≥1,5 mm2

L1 L2 L3

T1 T2 T3 T4

7-digit identification field Quadrant reading Status reading

Unit field

Tariff reading

Phase indication

Value field

With built-in radio

If the meter is supplied with integral radio for establishment of remote reading, the

meter automatically connects to a radio network. The integral radio is equipped with

an internal antenna. The radio signal strength can be read by means of a hand-held

terminal. If the radio signal is not sufficient, an external antenna must be connected.

Please see current documentation on available antennas.

Mounting a communication module in the meter may influence communication, please

contact Kamstrup.

With disconnection function

With this type of meter, it must be checked that the red/green diode is not switched on.

This indicates that the consumer’s supply is switched off.

Installation dimensions

Connection diagrams

The valid connection diagram appears from the type label.

3-phase, 4-wire 3-phase, 3-wire (Aron)

201,6

166,9

684-38A-C4-00-010

Sn:

3 x230/400V

50 Hz

LED/S0:1000 imp/kWh

0,5-5(85)A

Kl. A (3) EN 62053-23

EN 50470 1/3

2007W13

40 +70C

T10063

201,5

166,9

5512474_E1_GB_11.2010

123456789101112

P+

S0 +

20 -

123456789101112

P+

S0 +

20 -

Inhaltsverzeichnis

Andere Kamstrup Messgerät Handbücher

Kamstrup

Kamstrup ULTRAFLOW 54 DN150-300 Stücklistenhandbuch

Kamstrup

Kamstrup MULTICAL 302 Stücklistenhandbuch

Kamstrup

Kamstrup MULTICAL 803 Bedienungsanleitung

Kamstrup

Kamstrup MULTICAL 62 Stücklistenhandbuch

Kamstrup

Kamstrup MULTICAL 21 Stücklistenhandbuch

Kamstrup

Kamstrup MULTICAL 302 Bedienungsanleitung

Kamstrup

Kamstrup MULTICAL 602 Bedienungsanleitung

Kamstrup

Kamstrup MULTICAL 601 Bedienungsanleitung

Kamstrup

Kamstrup flowIQ 3100 Stücklistenhandbuch

Kamstrup

Kamstrup M-Bus Stücklistenhandbuch

Kamstrup

Kamstrup ULTRAFLOW 54 DN15-125 Stücklistenhandbuch

Kamstrup

Kamstrup MULTICAL 61 Bedienungsanleitung

Kamstrup

Kamstrup MAXICAL III Bedienungsanleitung

Kamstrup

Kamstrup flowIQ 2102 Bedienungs- und Wartungsanleitung

Kamstrup

Kamstrup ULTRAFLOW 54 Bedienungsanleitung

Kamstrup

Kamstrup MULTICAL 602 Bedienungsanleitung

Kamstrup

Kamstrup MULTICAL 403 Stücklistenhandbuch

Kamstrup

Kamstrup MULTICAL 403 Stücklistenhandbuch

Kamstrup

Kamstrup MULTICAL 62 Stücklistenhandbuch

Kamstrup

Kamstrup MULTICAL 402 Montage- und Bedienungsanleitung

Kamstrup

Kamstrup MULTICAL 41 Stücklistenhandbuch

Kamstrup

Kamstrup MULTICAL 62 Bedienungsanleitung

Kamstrup

Kamstrup flowIQ 3100 Bedienungs- und Montageanleitung

Kamstrup

Kamstrup MULTICAL 6M2 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung