Kamstrup 382 Bedienungsanleitung

Manual

Kamstrup 382

www.kamstrup.com

Operating instructions

Connect the meter in accordance with the installation diagram on the meter’s type label.

Depending on the configuration a fixed value will be displayed, or the display will

change between selected indications every 10 seconds.

It is possible to change the display reading manually by activating the push button on

the meter. The available readings will depend on the meter’s configuration.

Security and installation guidelines

The meter shall only to be used for measuring electrical energy and shall operate within

the specified values only.

The meter must be switched off when working on it. It can be highly dangerous to touch

the meter parts when the meter is switched on.

Therefore, the relevant security fuse must be removed and kept in a place where it cannot

be inserted by unauthorized persons.

Current local standards, guidelines, regulations and instruction must be observed. Only

authorized personnel is permitted to install electricity meters.

Meters for direct connection must be protected against short circuit by a security fuse in

accordance with the maximum current stated on the meter.

The meter constant LED blinks proportionally to the consumed active energy.

Only authorized personnel must break the utility sealing.

LCD-displayLCD-display

LED (meter constant)LED (meter constant)

Optical interfaceOptical interface

Push buttonPush button

Type labelType label

The phase indications L1, L2 and L3 have more than one function, they indicate one of

three situations described below:

Segments L1- L3 Indicate

On Both voltage and load above minimum limit.

Active phases indicate consumption.

Off The voltage is below minimum limit.

Blinking Segments L1 – L3 function as load indicators. Voltage is above and

load is below minimum limit.

The load indicator is active 4 hours after meter reset.

If the load exceeds the minimum limit and the meter is configured with this reading,

consumption will be indicated via the quadrant reading.

The meter’s LED can be used provided that the quadrant indicator is not selected.

The measured unit is displayed in the right side of the display.

Tariff indicating active tariff.

Terminals

Size: 1,5 – 25 mm2

1,5 – 35 mm2

Screw: Pz 2

Torch: 2,5 – 3 Nm

LCD display

L1 L2 L3

T1 T2 T3 T4

7-digit identification field Quadrant reading Status reading

Unit field

Tariff reading

Phase indication

Value field

Installation dimensions

Connection diagrams

The valid connection diagram appears from the type label.

3-phase, 4-wire 3-phase, 3-wire (Aron)

201,6

166,9

684-38A-C4-00-010

Sn:

3 x230/400V

50 Hz

LED/S0:1000 imp/kWh

0,5-5(85)A

Kl. A (3) EN 62053-23

EN 50470 1/3

2007W13

40 +70C

T10063

- -

201,5

166,9

123456789101112

P+

S0 +

20 -

123456789101112

P+

S0 +

20 -

5512-474 GB/04.2007/Rev. A1

Inhaltsverzeichnis

Andere Kamstrup Messgerät Handbücher

Kamstrup

Kamstrup MULTICAL 601 Bedienungsanleitung

Kamstrup

Kamstrup MULTICAL 62 Stücklistenhandbuch

Kamstrup

Kamstrup MULTICAL 603 Stücklistenhandbuch

Kamstrup

Kamstrup 382 Bedienungsanleitung

Kamstrup

Kamstrup MULTICAL 401 Stücklistenhandbuch

Kamstrup

Kamstrup 66-99-279 Handbuch

Kamstrup

Kamstrup M-Bus Stücklistenhandbuch

Kamstrup

Kamstrup ULTRAFLOW 54 Stücklistenhandbuch

Kamstrup

Kamstrup MULTICAL 402 Bedienungsanleitung

Kamstrup

Kamstrup 162M Stücklistenhandbuch

Kamstrup

Kamstrup MULTICAL 603 Bedienungsanleitung

Kamstrup

Kamstrup OMNIPOWER Bedienungsanleitung

Kamstrup

Kamstrup MAXICAL III Bedienungsanleitung

Kamstrup

Kamstrup flowIQ 2102 Bedienungs- und Wartungsanleitung

Kamstrup

Kamstrup ULTRAFLOW 54 Bedienungsanleitung

Kamstrup

Kamstrup MULTICAL 62 Bedienungsanleitung

Kamstrup

Kamstrup MULTICAL 402 Stücklistenhandbuch

Kamstrup

Kamstrup MULTICAL 801 Stücklistenhandbuch

Kamstrup

Kamstrup flowIQ 2101 Stücklistenhandbuch

Kamstrup

Kamstrup ULTRAFLOW 54 Series Stücklistenhandbuch

Kamstrup

Kamstrup flowIQ 3100 Bedienungs- und Montageanleitung

Kamstrup

Kamstrup ULTRAFLOW 54 DN150-300 Stücklistenhandbuch

Kamstrup

Kamstrup MULTICAL 62 Stücklistenhandbuch

Kamstrup

Kamstrup MULTICAL 801 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung