Kargo Master 4089D Handbuch

Kargo Master

Rancho Cordova, CA 95742

800-343-7486

CustomerService@KargoMaster.com

20210812R1 DATE: ________________

Instruction Guide

4089D

Instructions –4089D

For Technical Support Call: 800-343-7486, Monday-Friday, 7AM - 4 PM (PST) Page 1

*PLEASE READ ALL INSTRUCTIONS AND WARNINGS PRIOR TO ASSEMBLING, INSTALLING,

AND USING THIS PRODUCT. *

Warning

Always check for wires, fuel tanks and lines, brake lines and other important vehicle

functionality items prior to drilling and installing all products.

DO NOT EXCEED MANUFACTURERS WEIGHT CAPACITY FOR ROOF.

Tools Needed

9/16” Socket and Wrench

9/16” Box Wrench

10mm, 13mm Sockets and Wrench

13mm Box Wrench

Table of Contents

Before You Begin............................................................................................................................................... 1

Parts .................................................................................................................................................................. 2

Hardware .......................................................................................................................................................... 2

Transit Connect Installation.............................................................................................................................. 4

ProMaster City Installation ............................................................................................................................... 5

NV200/City Express Installation........................................................................................................................ 7

Camper Shell Installation.................................................................................................................................. 8

Before You Begin

Read all instructions prior to assembling or installing any Kargo Master product.

Always locate your installation locations prior to performing any work.

Be sure to put sealant around all threads entering cargo area and between the rubber spacer and roof

of vehicle to prevent water from leaking into cargo area.

These instructions are for the mounting kit only. Refer to the instructions that came with the rack for

help with rack assembly.

Instructions –4089D

For Technical Support Call: 800-343-7486, Monday-Friday, 7AM - 4 PM (PST) Page 2

Parts

Hardware

Instructions –4089D

For Technical Support Call: 800-343-7486, Monday-Friday, 7AM - 4 PM (PST) Page 3

Hardware (Continued)

Instructions –4089D

For Technical Support Call: 800-343-7486, Monday-Friday, 7AM - 4 PM (PST) Page 4

DO NOT EXCEED MANUFACTURERS WEIGHT CAPACITY FOR ROOF

Transit Connect Installation

Locate the plugs on the roof of the

van in the locations shown.

Remove the plugs from the roof in

the FOUR desired mounting

locations to expose mounting slots.

ONLY REMOVE PLUGS FROM FOUR

INTENDED INSTALLATION

LOCATIONS.

Apply sealant around mounting slots in the roof.

Place the three-hole rubber pad on top of the van with the center hole over the mounting location. Be

sure the sealant is applied to prevent water from leaking into the cargo area.

Place the foot on top of the three-hole rubber pad with the cup of the foot facing outwards.

Using a M8 x 30mm hex head, 5/16” flat washer, bolt through bottom-center hole in foot, center of

three-hole pad, and then hole in top of roof. Inside roof, bolt through round rubber washer, 5/16” fender

washer, and M8 lock nut. The roof sandwiches between rubber pad and rubber washer.

Snug tighten, but allow movement.

Repeat for remaining three installation locations.

Mount rack to feet per instructions that came with rack.

ALL RACKS

8008A

8010A & 8012A

Use

M8 x 30mm

bolts here.

Instructions –4089D

For Technical Support Call: 800-343-7486, Monday-Friday, 7AM - 4 PM (PST) Page 5

ProMaster City Installation

Remove the plugs from the

roof in the FOUR mounting

locations shown to expose the

threaded inserts. ONLY

REMOVE PLUGS FROM FOUR

INTENDED INSTALLATION

LOCATIONS.

Rear and Front Mount Locations:

Apply sealant around the threaded inserts in the roof.

Place the three-hole rubber pad on top of the van with the TWO OUTER HOLES over the threaded inserts.

Be sure to apply sealant thoroughly to prevent water from leaking into the cargo area.

Bolt through the foot into the threaded inserts in the roof using M6 x 22mm hex heads, 1/4” lock

washers, and 1/4” flat washers, in the order shown.

Snug tighten, but allow movement.

Repeat for opposite side of vehicle.

8008A

8010A & 8012A

ALL RACKS

Use

M6 x 22mm

bolts here.

Instructions –4089D

For Technical Support Call: 800-343-7486, Monday-Friday, 7AM - 4 PM (PST) Page 6

ProMaster City Installation (Continued)

Mid Mount Location (8008A only):

Apply sealant around the threaded insert in the roof.

Place the RUBBER WASHER on top of the van CENTERED over the threaded insert. Be sure to apply

sealant thoroughly around threaded insert to prevent water from leaking into the cargo area.

Place the foot on top of the rubber washer with the cup of the foot facing outwards.

Using M6 x 22mm hex heads, 1/4” lock washers, and 1/4” flat washers, bolt through foot into the

threaded inserts in the roof, in the order shown.

Snug tighten, but allow movement.

Repeat for opposite side of vehicle.

Mount rack to feet per instructions that came with rack.

Use

M6 x 22mm

bolts here.

Instructions –4089D

For Technical Support Call: 800-343-7486, Monday-Friday, 7AM - 4 PM (PST) Page 7

NV200/City Express Installation

Remove the plugs from the

roof in the FOUR mounting

locations shown to expose the

threaded inserts. ONLY

REMOVE PLUGS FROM FOUR

INTENDED INSTALLATION

LOCATIONS.

Apply sealant around the threaded inserts in the roof. Be sure to apply sealant thoroughly to prevent

water from leaking into the cargo area.

Place the three-hole rubber pad on top of the van with the center hole over the threaded insert.

Place the foot on top of the three-hole rubber pad with the cup of the foot facing outwards.

Bolt through the foot into the threaded inserts using a M8 x 30mm hex head, 5/16” lock washer,

5/16” flat washer and a rubber pad in the order shown.

Repeat for remaining three locations.

Snug tighten, but allow movement.

Mount rack to feet per instructions that came with rack.

Use

M8 x 30mm

bolts here.

8008A

8010A & 8012A

ALL RACKS

Instructions –4089D

For Technical Support Call: 800-343-7486, Monday-Friday, 7AM - 4 PM (PST) Page 8

Camper Shell Installation

Find the desired ladder location on top of camper shell. Some caps will have reinforced mounting

locations built into the cap. THIS STEP MAY BE EASIER IF THE FEET ARE INSTALLED ON THE RACK.

Place the feet on top of the camper shell in the desired location.

Mark through the slots in the feet onto the top of the camper shell. Be sure the marked location is safe

to drill.

Drill the center of each slot using a 5/16” drill.

APPLY SEALANT around the exposed holes in the cap to help prevent water from leaking into the cargo

area.

Place a three-hole rubber pad on top of the holes in the cap.

Place the foot on top of the rubber pad.

Bolt through the foot, the rubber pad and the camper shell using two M8 x 40mm hex heads and two

5/16” flat washers.

From the inside of the camper shell, LOOSELY attach a rubber washer, a 5/16” fender washer and M8 lock

nut onto bolts.

Thoroughly APPLY SEALANT around the holes in the foot and rubber pad.

Snug tighten, but allow movement.

Repeat at remaining three locations.

Mount rack to feet per instructions that came with rack.

Use

M8 x 40mm

bolts here.

Inhaltsverzeichnis

Andere Kargo Master Rack & Stand Handbücher

Kargo Master

Kargo Master 406SL Bedienungsanleitung

Kargo Master

Kargo Master 40960 Handbuch

Kargo Master

Kargo Master 40240 Bedienungsanleitung

Kargo Master

Kargo Master 40370 Bedienungsanleitung

Kargo Master

Kargo Master 40280 Bedienungsanleitung

Kargo Master

Kargo Master 4A95M Bedienungsanleitung

Kargo Master

Kargo Master 4080L Handbuch

Kargo Master

Kargo Master 4A96L Handbuch

Kargo Master

Kargo Master 40641 Bedienungsanleitung

Kargo Master

Kargo Master 42000 Handbuch

Kargo Master

Kargo Master 4826L Bedienungsanleitung

Kargo Master

Kargo Master 4A83L Handbuch

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Kargo Master

Kargo Master 4A934 Handbuch

Kargo Master

Kargo Master 4064M Bedienungsanleitung

Kargo Master

Kargo Master 40390 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung

Vivo

Vivo MOUNT-HP23XW Bedienungsanleitung