Keller LEX 1 Bedienungsanleitung
LEX 1
LEX 1
Actual Value
Max.- / Min.-Value
ENTER
Max. / Min.
SELECT
G 1/4”
Highly Precise Digital Manometer
KELLER AG St. Gallerstrasse 119 CH-8404 Winterthur Tel. ++41 (0)52 235 25 25
KELLER GmbH Schwarzwaldstrasse 17 D-79798 Jestetten Tel. ++49 (0)7745 9214 0
www.keller-druck.com
LEX 1 has two operating keys. The left key (SELECT) serves to select
the functions and the pressure units. The right key (ENTER) activates
the selected function or pressure unit. The right key is also used to
switch between the Max.- and Min.-value.
Turn-on: Pressing the SELECT key turns the instrument on. The
instrument first displays the software version (year/week) and the full-
scale pressure range. The instrument is then ready for use and indi-
cates the actual pressure (top display) and the last measured Max.-
value (bottom display).
The instrument has the following functions:
RESET: Max.-/Min.-value are set to the actual pressure
OFF: Turns off the instrument
MANO: Releases the following functions:
ZERO SEt: Sets a new Zero reference
ZERO rES: Sets the Zero to factory setting
CONT on: Deactivates the automatic turn-off function
CONT off: Activates the automatic turn-off function (the instrument
turns off 15 minutes after the last key function)
followed by the unit selection: bar, mbar, hPa, kPa, MPa, PSI,
kp/cm2, cmH2O, mH2O, inH2O, ftH2O, mmHg, inHg
Example: Setting a new pressure unit (mbar):
--> Turn on the instrument by shortly pressing the SELECT-key.
--> Wait for the instrument’s measuring mode (approx. 3 seconds).
--> Press the SELECT-key 3 times: MANO appears.
--> Press ENTER: ZERO SEt appears.
--> Press SELECT: ZERO rES appears.
--> Press SELECT: CONT on or CONT off appears.
--> Press SELECT: bar appears.
--> Press SELECT: mbar appears.
--> Press ENTER: The new pressure unit (mbar) is set.
The instrument returns to the measuring mode.
2
Display of the minimum pressure value
When in the measuring mode (Display: Actual Pressure and Max.-
value), you may display the Min.-value for 5 seconds by shortly pres-
sing the ENTER-key.
Notes
• The functions and units can also be called up by keeping the
SELECT-key depressed. Releasing the key enables the displayed
function or unit to be activated with the ENTER-key.
• If the selected function or unit is not activated within 5 seconds
with the ENTER-key, LEX 1 returns to the measuring mode with-
out changing any settings.
• Turning LEX 1 on and off does not influence any of the previous
settings.
• If the CONT on function is activated, it is indicated with a flashing
sign (cont) on the display.
• If a pressure can not be represented on the display, OFL (over-
flow) or UFL (underflow) appears on the display.
• If the actual pressure goes beyond the measuring range, the last
valid pressure value starts flashing on the display.
Installation
Screw the G1/4 male port of LEX 1 into the female
pressure port and tighten using the lower
hexagon of the transducer. Loosen the
upper hexagon and rotate the LEX 1
to the desired position. Retighten.
3
The face of LEX 1 can be
rotated through 355°. This feature allows the LEX 1
to be mounted in all possible positions; vertical,
horizontal or upside down.
KELLER
S
E
L
E
C
T
E
N
T
E
R
w
w
w
.
k
e
l
l
e
r
-
d
ru
c
k
.
c
h
s
w
i
s
s
m
a
d
e
M
a
x
.
/
M
i
n
.
KELLER
S
E
L
E
C
T
E
N
T
E
R
w
w
w
.
k
e
l
l
e
r
-
d
ru
c
k
.
c
h
s
w
i
s
s
m
a
d
e
M
a
x
.
/
M
i
n
.
Battery Change / Battery Life
When the battery starts weakening, a low battery warning will appear
(BAT LOW).
Battery change (turn off the instrument before changing the battery!):
Open the battery compartment and change the battery (type CR
2430). Make sure that the O-ring remains embedded in the cover.
The battery life is 2000 hours in normal measuring mode.
Ranges / Calibration
The factory setting of the Zero for the ranges ≤31 bar is at 0 bar abso-
lute. For sealed gauge pressure measurements, activate “ZERO SEt”
at ambient pressure. Instruments with ranges >31 bar are calibrated
in a sealed gauge mode at ambient pressure.
Interface (RS485)
The interface converter K103A (RS232) or K104A (USB) can be
connected at the back of the manometer, allowing the data transfer to
the PC. The corresponding software can be found on our web site.
01 / 2005www.keller-druck.com
4
Inhaltsverzeichnis
Andere Keller Messgerät Handbücher
Keller
Keller LEX 1 Ei Bedienungsanleitung
Keller
Keller dV-2 Cool Bedienungsanleitung
Keller
Keller LEX 1 Bedienungsanleitung
Keller
Keller ECO 2 Bedienungsanleitung
Keller
Keller LEO2-Ei Bedienungsanleitung
Keller
Keller LEO 1 Ei Bedienungsanleitung
Keller
Keller CellaTemp PA 4 Series Bedienungsanleitung
Keller
Keller LEO-Record-Ei Bedienungsanleitung
Keller
Keller CellaTemp PX1 Series Bedienungsanleitung
Keller
Keller LEO 5 Bedienungsanleitung
Keller
Keller CellaTemp PA 1 Series Bedienungsanleitung
Keller
Keller LEO 1 Bedienungsanleitung
Keller
Keller CellaTemp PK Series Bedienungsanleitung
Keller
Keller CellaCast PA8 Series Bedienungsanleitung
Keller
Keller LEO 5 Bedienungsanleitung
Keller
Keller dv-2 Bedienungsanleitung
Keller
Keller CellaTemp PR11 Bedienungsanleitung
Keller
Keller LEO 5 Bedienungsanleitung
Keller
Keller LEO1-Ei Bedienungsanleitung
Keller
Keller EV-97 Bedienungsanleitung
