KERN DLB A01N Bedienungsanleitung
KERN & Sohn GmbH
Ziegelei 1
D-72336 Balingen
E-Mail: info@kern-sohn.com
Phone: +49-[0]7433- 9933-0
Fax: +49-[0]7433-9933-149
Internet: www.kern-sohn.com
Operating instructions
Temperature Calibrating set
KERN DLB_A01N
Version 1.1
2020-12
GB
DLB_A01N-BA-e-2011
2 DLB_A01N-BA-e-2011
GB
KERN DLB_A01N
Version 1.12020-12
Operating manual
Temperature Calibrating set
Contents
1Preparation ......................................................................................................... 3
2TDLG 160-3-A ..................................................................................................... 4
2.1 Calibration of temperature value ...................................................................... 4
2.2 Adjustment of temperature value ..................................................................... 5
3DLB 160-3 ........................................................................................................... 7
3.1 C alibration of temperature value ...................................................................... 8
3.2 Adjustment of temperature value ..................................................................... 9
DLB_A01N-BA-e-2011 3
1 Preparation
We recommend sometimes to check the temperature value of the models using the
optional temperature calibrating set DLB-A01N.
Before you do this, allow the device to
cool down for at least 30 minutes after the last heating phase.
Install the temperature-calibration set acc. to illustration.
1.
Switch-on the moisture analyzer.
Close heating cover.
For further information on how to operate the moisture meter please refer to the
operating instructions enclosed with each model.
4 DLB_A01N-BA-e-2011
2 TDLG 160-3-A
2.1 Calibration of temperature value
During temperature calibration only a check is carried out, i.e. no values are changed.
1. In the start display press the F1-key, the main menu will appear.
2. Press to select the menu item <6 - Temperature Test> .
3. Acknowledge by .
Press to acknowledge the following instruction how to use a temperature
calibration set DLB-A01N. The current setting is displayed
4. Select desired test temperature with and acknowledge by .
The device heats up the set temperature.
5. After 15 minutes the test is finished, an acoustic signal sounds. Compare the test
temperature with the displayed temperature of the DLB-A01N. If the two values
do not match, we recommend a temperature adjustment, see chap. 2.2
6. Press to cancel the calibration.
DLB_A01N-BA-e-2011 5
2.2 Adjustment of temperature value
If in temperature calibration the admitted divergence is exceed or not reached, the
temperature of the instrument can be adjusted as described below.
1. In the start display press the F1-key, the main menu will appear.
2. Press to select the menu item <7 – Heater Calibration> and confirm by
.
3. Confirm the inquiries <Are you sure> and the following instruction how to use a
temperature calibration set DLB-A01N by .
The current settings of the both temperature points T-lo / T-hi are displayed.
4. Press to select the desired test temperature and press to
select between <T-lo> and <T-hi>. Acknowledge with .
5. Press , the first heating phase is started.
6 DLB_A01N-BA-e-2011
6. Temperature calibration for the first point takes 15 min. Compare the temperature
displayed on the DLB-A01N with that of the moisture analyzer.
If the two values do not match, read off the value at the temperature calibration
set and enter with the help of .
7. Confirm by , the second heating phase is started.
8. Temperature calibration for the second point takes 15 min. Compare the
temperature displayed on the DLB-A01N with that of the moisture analyzer.
If the two values do not match, read off the value at the temperature calibration
set and enter with the help of and confirm by .
9. When an optional printer is connected, an adjustment log can be edited.
10.Press to return into menu / start display.
DLB_A01N-BA-e-2011 7
3 DLB 160-3
Invoke service function:
In weighing mode press the MENU button and keep it pressed until the acoustic
signal gets mute. Release the button and the menu item “units“ will appear.
Press repeatedly the MENU button until „Service“ will be displayed.
Confirm by pressing the PRINT button. Select the required settings by pressing
the MENU button
Calibration of temperature, see chap. 3.1
Adjustment of temperature, see chap. 3.2
Settings of lamp
8 DLB_A01N-BA-e-2011
3.1 Calibration of temperature value
During temperature calibration only a check is carried out, i.e. no values are changed.
Invoke service function „Tmp test“, see chap. 3
Confirm by pressing the PRINT button. The current setting will be displayed. Use
the navigation buttons to select the temperature during the check, available
35- 160°C, e.g. 120°C.
Confirm using the PRINT button, the appliance heats up to the set temperature.
After approx. 15 minutes compare the test temperature with the displayed
temperature of the DLB-A01N. If the two values do not match, we recommend a
temperature adjustment, see chap. 3.2
Use the ON/OFF button to finish the calibration.
Use the ON/OFF button to return into weighing mode.
DLB_A01N-BA-e-2011 9
3.2 Adjustment of temperature value
The temperature is measured at two selectable points and it is possible to correct it
there.
Invoke service function „Tmp Adj“, see chap. 3
Confirm by pressing the PRINT button. The current setting for the first
temperature point is displayed. Or leave it on factory setting 80°C or select a
desired temperature with the help of the navigation buttons (available 50-
130°C).
Confirm with the PRINT button, the first heat-up phase is started. The remaining
time is displayed.
Temperature calibration for the first point takes 15 min. Compare the temperature
displayed on the DLB-A01N with that of the moisture analyzer. If the two values
do not match, correct them using the navigation buttons and confirm with the
PRINT button
.
The current setting for the second temperature point is displayed. Or leave it on
factory setting 150°C or select the desired temperature with the help of the
navigation buttons . The second temperature point has to be at least 30°C
over the first one, max. 160°C.
Confirm with the PRINT button, the second heat-up phase is started. The
remaining time is displayed.
Temperature calibration for the second point takes 15 min. Compare the
temperature displayed on the DLB-A01N with that of the moisture analyzer. If the
two values do not match, correct with the help of the navigation buttons .
Confirm by pressing the PRINT button. The adjustment is completed, the
appliance returns into the menu. Use the ON/OFF button to return into weighing
mode.
Inhaltsverzeichnis
Andere KERN Messgerät Handbücher
KERN
KERN DBS 60-3 Bedienungsanleitung
KERN
KERN MSF 200N Bedienungsanleitung
KERN
KERN MLB-A03 Bedienungsanleitung
KERN
KERN YDB-02 Bedienungsanleitung
KERN
KERN ORA 10 BB Bedienungsanleitung
KERN
KERN KIB-A12 Bedienungsanleitung
KERN
KERN ORA 3AA/AB Beer Bedienungsanleitung
KERN
KERN KFE-TM Bedienungsanleitung
KERN
KERN ORA 20 BA Bedienungsanleitung
KERN
KERN mlb-c Bedienungsanleitung
KERN
KERN MLS 50-3IR160 Bedienungsanleitung
KERN
KERN ORA 1UA Bedienungsanleitung
KERN
KERN ORA 10 BA Bedienungsanleitung
KERN
KERN KFB-TM Bedienungsanleitung
KERN
KERN DLT-N Bedienungsanleitung
KERN
KERN ORD 45BM Bedienungsanleitung
KERN
KERN DLB 160-3A Bedienungsanleitung
KERN
KERN DAB-SH-e-1610 Bedienungsanleitung
KERN
KERN TMBA-A01-A Bedienungsanleitung
KERN
KERN MBC-A01 Bedienungsanleitung
