Key Digital KD-X222PO Bedienungsanleitung

4K HDMI over CAT5e/6 HDBaseT Extender Tx + Rx Kit.

10.2Gbps Bandwidth. IR Emitter and Sensor Included.

The Experts in Digital Video Technology and Solutions™

Operating Instructions

KD-X222PO

Table of Contents

Key Features ..................................................................1

Quick Setup Guide ..............................................................2

Installation and Operation .........................................................2

Application Example .............................................................3

Connections ...................................................................4

Extending IR or RS-232 Control .....................................................5

Settings ......................................................................8

LED Indicator Lights ............................................................10

RS-232 Commands ............................................................10

Speciﬁcations .................................................................12

Always follow the instructions provided in this Operating Manual.

Please visit www.keydigital.com for the latest product documentation and software

downloads. Product features and speciﬁcations are subject to change without notice.

Introduction

Key Digital®KD-X222PO HDBaseT/HDMI (Tx + Rx) Extenders are an HDCP 2.2 compliant product that

extend 4K/UHD 24/25/30 (4:4:4) and 4K/UHD 60 (4:2:0) signals up to 150 ft. using CAT6A cable, or

up to 125 ft. using a CAT5e/6 cable. 1080p/60, 1920x1200, 3D signals are extended up to 250 ft.

via CAT6A cable, or up to 230 ft. using a CAT5e/6 cable. In addition to HDMI video and audio signals,

KD-X222PO carries IR or RS-232 for controlling remotely located equipment or the RS-232 port can

be used to control the KD-X222PO.

Key Features

›HDBaseT via Single CAT5e/6 UTP/STP Extension: With fully automatic adjustment of feedback,

equalization, and ampliﬁcation depending on cabling length

›Power over HDBaseT: Tx unit powers Rx unit. Only one power connection needed.

›Signal Extension:

»Up to 150 ft. @ 4K 24/25/30(4:4:4)/60(4:2:0) using CAT6A cabling

»Up to 125 ft. @ 4K 24/25/30(4:4:4)/60(4:2:0) using CAT5e/6 UTP/STP cabling

»Up to 250 ft. @ 1080p / 1920x1200 using CAT6A cabling

»Up to 230 ft. @ 1080p / 1920x1200 using third-party CAT5e/6 UTP/STP cabling

›HDCP 2.2: Compliancy up to HDCP 2.2 and backward compliant

›HDR (High Dynamic Range): HDR is achieved with AppleTV source at 4K/30 [4:2:2] 12bit deep

color, enabling more life-like images through a greater range of luminance levels.

›4K/Ultra HD Resolution: Supports signals up to 4096x2160 60Hz [4:2:0] 8bit, 4096x2160 30Hz

[4:2:2] 12bit, and 4096x2160 30Hz [4:4:4] 8bit

›Deep Color Support: Up to UHD/4K 30Hz 4:2:2/12 bits or 60Hz 4:2:0/8 bit

›Low Proﬁle: Super slim chassis design

›HDMI®and HDCP Licensing: Fully licensed and compatible with HDCP 2.2 and HDMI latest

technology such as 4K/UHD 4:2:0/8bit at 60f/s

›EDID Control: Internal library features 15 default EDID conﬁgurations and native EDID data from

Output/Display devices connected via Rx

›Hot Plug Detection Control: Enables integrator to choose if active signal voltage is forced to

connected input devices

›Full Buffer System™:Manages TMDS re-clocking / signal re-generation, HDCP authentication

with source & display, EDID Control handshake, and Hot Plug control

›IR Sensor: Sensor powering via +5V on Rx unit’s IR In port collects line-of-sight IR from remote(s)

without external IR connecting block

›Up/Down IR: Two channels of IR enable control to/from devices connected to Tx and Rx units

›RS-232: Bi-Directional control to/from Tx and Rx unit on Phoenix connector

›Rotary Switch RS-232 Control Mode: Provides control of Tx unit as well as connectivity status

›3D: Support for standard 3D stereoscopic signal formats

›Surround Sound Audio: Supports Dolby®TrueHD, Dolby®Digital Plus, Dolby Atmos®, and DTS-HD

Master Audio™multi-channel audio formats

›CEC Support: For inter-device control between input and output HDMI channel

›I2C Communication: EDID and HDCP authentication to Display and Source

›Control System Support: Fully controllable by all RS-232 supported control systems via open API:

Compass Control®, AMX®, Crestron®, KNX®, RTI®, Savant, URC®, Leviton®etc.

Accessories

›(1) 12V 2A DC Power Supply (Screw-In Type), model KD-PS12V2ASC, (2) Mounting Brackets,

(1) IR Emitter, (1) IR Sensor

›KD-X222PO only requires power on the Tx unit, which extends power to the Rx unit

Quick Setup Guide

Step 1: Find a safe and convenient location to mount or place your KD-X222PO units

Step 2: Begin with the KD-X222PO Tx/Rx units and all input/output devices turned off with power

cables removed

Step 3: Connect your HDMI source to the input port of your KD-X222PO Tx unit

Step 4: Connect your HDMI displays to the output port of your KD-X222PO Rx unit

Step 5: Connect KD-X222PO Rx unit to KD-X222PO Tx with CAT5e/6 cable using 568-B termination.

Step 6: Connect additional IR/RS-232 control connections and IR sensors

Step 7: Set the EDID rotary to position A for 4K resolution with 2ch audio. For 1080p with 2ch audio,

use position 7. Refer to the SETTINGS section for more information

Step 8:

BEFORE

connecting power supply to power outlet, screw-in the power supply to the

KD-X222PO Tx unit

Step 9:

AFTER all connections are made, plug-in power supplies to power outlets

Step 10: Power on input/output devices

Installation and Operation

Before permanently securing the unit for ﬁnal installation, test for proper operation of the unit and cables

in your system. It is recommended that you leave enough ventilation space to provide sufﬁcient airﬂow

and cooling.

You MUST use the Power Supply PROVIDED with your unit or you VOID the Key Digital®

Warranty and risk damage to your unit and associated equipment.

Application Example

Up to 150 ft.@ 4K

WiFi

RS-232

HDMI

CAT5e/6

WiFi Router

Master Controller

KD-MC1000

KD-X222PO

RS-232

Cable / Satellite

Technical Support:

email: [email protected]

phone: 914.667.9700 ext 3

www.keydigital.com/compass

Compass Control®Pro Site

521 East 3rd Street • Mount Vernon • NY 10553

phone: 914.667.9700 • fax: 914.668.8666

Enterprise Software License

for Compass Control®Pro

Supports iOS & Android

KD-ProCL8

KD-ProCL6

KD-ProCL4

KD-ProCL1

IR Out

Connections

Before making any connections, power off your source and display devices.

Tx Unit:

›Using a short HDMI cable, connect your source device to the HDMI port labeled “HDMI Input”.

For DVI-D/DVI-I sources, use appropriate adapters. For Display Port, use active converters.

›Connect the CAT5e/6 UTP or STP cable that connects to the Rx Unit at the port labeled

“CAT5e/6 Output”. Use 568-B Termination.

›Make IR In and Out connections to receive (IR In port) or send (IR Out port) control signals.

Refer to the “Extending IR & RS-232 Control” for more information.

›Connect a stripped wire to DB9 adapter cable for bi-directional RS-232 control.

Refer to the “Extending IR or RS-232 Control” and the “RS-232 Commands” section for more

information.

Rx Unit:

›Using a short HDMI cable, connect your output / display device to the HDMI port labeled

“HDMI Output”.

›Connect the CAT5e/6 cable at the port labeled “CAT5e/6 Input”. Use 568-B Termination.

›If you are sending or receiving IR, connect included IR Sensor and/or IR Emitter.

›If you are transmitting or receiving RS-232, connect to the IR out (RS-232) port.

›After all the connections are made, connect power using the included power supply and then

power up your source and display equipment.

Extending IR or RS-232 Control

RS-232:

Bi-directional RS-232 is achieved utilizing the IR Out (RS-232) port on the Tx and Rx units. The

connector is 3-pin phoenix and the pinout is the same on the Tx and Rx unit. RS-232 can not be used

at the same time as IR.

›RS-232 Pass-through Mode

»Send and receive (bi-directional) RS-232 commands for controlling remote equipment. Supports

baud rate up to 115,200bps.

›Control Mode

»Provides control of Tx units as well as connectivity status

»See RS-232 Commands section for more information

›Firmware Upgrade Mode

»Two different types of ﬁrmware may be updated: MCU (KD-X222PO units), and HDBaseT

(extension over CAT5e/6)

RS-232 Cabling

RS-232 cables are available through Key Digital and other wire suppliers, and can also be fabricated by

skilled technicians.

Key Digital RS-232 Cable Pinout Charts

Model Wire DB9 Pin Signal

KD-3.5FDB96

3.5mm Stereo to Female DB9 (sold separately)

Red 2 TxD

White 3 RxD

Black 5 Ground

Green N/C NA

KD-3.5FDB96 with 3.5mm TRS Connector KD-3.5FDB96 after stripping wire

Model Wire DB9 Pin Signal

KD-3.5MDB96

3.5mm Stereo to Male DB9 (sold separately)

Red 2 TxD

Black 3 RxD

Shield 5 Ground

KD-3.5MDB96 with 3.5mm TRS Connector KD-3.5MDB96 after stripping wire

Bi-directional IR control extension is supported. IR can not be used at the same time as RS-232.

»“IR In” port on the Tx unit extends to the “IR Out” port of the Rx unit

»“IR In” port on the Rx unit extends to the “IR Out” port of the Tx unit

›IR In:

The IR In port is different for the Tx and Rx units. The Tx unit’s IR In port supports a Serial IR

(hardwired) connection. The Rx unit’s IR In port supports an IR Sensor.

»Tx Unit / Serial IR:

»A ﬁxed 5V input signal on 2 phoenix pins

»Signal and ground are required

»Typically fed from a dedicated control system or an IR distribution block

»Rx Unit / IR Sensor:

»IR Sensors can be connected directly into the Rx unit’s IR In port, without the need for an

external IR distribution block

»IR signal on the Tip, with 5V powering of the IR sensor on the power wire.

IR Sensor / IN Pinout Wire Signal

Red 5V Power

White IR Signal

Black Ground

›IR Out:

»Pass-through from signal of corresponding IR In port or bi-directional RS-232, as determined by

the position of the Control Rotary

»Driving power: 5V with 32mA minimum current

»Typically connected with an IR emitter

IR Emitter / OUT Pinout Wire Signal

Dashed/Marked IR Signal

Solid/Black Ground

IR Cabling

Your KD-X222PO includes an IR Sensor and an IR Emitter.

Signal acceptance: The IR Sensor receives signals from a 90° angle at up to 30 ft. away. It accepts a

maximum IR burst frequency of 55kHz.

Only the included IR sensors are compatible with the KD-X222PO. Third-party IR Sensors may not be

compatible.

The included IR Sensor.

Connects to the IR In port on the Rx unit.

The included blinking-type IR Emitter.

Connects to the IR Out port.

Settings

EDID Control

EDID authentication is provided from the KD-X222/ KD-X222PO Tx unit to the connected input / source

device. The EDID ﬁle (AKA “handshake”) is selected using the EDID Control rotary on the Tx unit and

provides a list of compatible video and audio formats as well as digital data, informing the source device

what it should output. Most sources will comply with a new EDID ﬁle without a power-cycle, but each

source may behave differently.

Default EDID Control Table, selected via EDID Control rotary

Position EDID Description EDID Control Rotary

0Copy EDID from CAT5e/6 Output

IMPORTANT! Please apply

light pressure to the Control

rotary when making your

selection

11080i, 2CH AUDIO

21080i, DOLBY/DTS 5.1

31080i, HD AUDIO

41080p, 2CH AUDIO

51080p, DOLBY/DTS 5.1

61080p, HD AUDIO

74Kx2K@30, 2CH AUDIO

84Kx2K@30, DOLBY/DTS 5.1

94Kx2K@30, HD AUDIO

A4Kx2K@60, 2CH AUDIO

B4Kx2K@60, DOLBY/DTS 5.1

C4Kx2K@60, HD AUDIO

D1280x720p@60 DVI (no audio)

E1920x1080@30 DVI (no audio)

F3840x2160p@30 DVI (no audio)

Control Rotary

The Control rotary enables the integrator to choose the desired setting for IR Out

(RS-232) ports, RS-232 Mode, and Hot Plug Detection control.

The Control Rotary is located on the Tx unit.

›IMPORTANT! Please apply light pressure to the Control rotary when making

your selection

Inhaltsverzeichnis

Andere Key Digital Extender Handbücher

Key Digital

Key Digital KD-X222 Bedienungsanleitung

Key Digital

Key Digital KD-EX18G Bedienungsanleitung

Key Digital

Key Digital KD-FIX418 Bedienungsanleitung

Key Digital

Key Digital Black Bull KD-CATDRV Tx Bedienungsanleitung

Key Digital

Key Digital KD-CAT5XCAT5 Bedienungsanleitung

Key Digital

Key Digital Phantom KD-HDDA1X1 Bedienungsanleitung

Key Digital

Key Digital FatCAT KD-CATHD Tx Bedienungsanleitung

Key Digital

Key Digital KD-X444LP Bedienungsanleitung

Key Digital

Key Digital KD-X422POA Bedienungsanleitung

Key Digital

Key Digital KD-IP120TX Bedienungsanleitung

Key Digital

Key Digital KD-PS22UTx Bedienungsanleitung

Key Digital

Key Digital KD-X444SP Bedienungsanleitung

Key Digital

Key Digital KD-HDMIXCAT5 Bedienungsanleitung

Key Digital

Key Digital KD-X400POHK Bedienungsanleitung

Key Digital

Key Digital KD-CATHD500Pro Bedienungsanleitung

Key Digital

Key Digital KD-HDB150 Bedienungsanleitung

Key Digital

Key Digital KD-CAT5XHDMI Bedienungsanleitung

Key Digital

Key Digital KD-CAT5XCAT5 Bedienungsanleitung

Key Digital

Key Digital KD-X444S Bedienungsanleitung

Key Digital

Key Digital KD-4KWHCEX Bedienungsanleitung

Key Digital

Key Digital KD-X411ProK Bedienungsanleitung

Key Digital

Key Digital Smart Baluns KD-BBRX Bedienungsanleitung

Key Digital

Key Digital KD-X600ProK Bedienungsanleitung

Key Digital

Key Digital KD-XUSB2 Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung

SECO-LARM

SECO-LARM ENFORCER EVT-PB1-V1TGQ Bedienungsanleitung